Sealey FSW80 User manual

INSTRUCTIONS FOR:
FLOOR SWEEPER 800MM
MODEL No. FSW80
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3.1 Lower Handle: Take the lower handle tube and place the slots in the
flattened ends over the threaded spigots on the handle brackets, see fig.1B.
Ensure that the open slots at each end of the lower handle are engaged with
the plain spigot on the mounting brackets. Retain the handle in place by
screwing a black plastic knob onto each threaded spigot.
3.2 Upper Handle: The upper handle has three alternative mounting holes in the
flattened portions of the handle. Align the chosen mounting holes with the
holes in the upper part of the lower handle and insert the supplied coach
bolts through both frames and retain with the black plastic knobs supplied as
shown in fig.1A.
3.3 Handle stowage: The handle can be folded down for storage purposes.
Loosen the lower mounting knobs and pull the handle upwards to disengage
the slotted ends from the plain spigots on the mounting brackets. Hinge the
handle forwards and allow it to rest on the body of the sweeper.
3.4 Circular brushes: Attach each brush to its hub using the 6 screws provided
(3 for each brush). Ensure each brush is correctly seated before tightening.
3.5 Use: Ensure the handle height is correctly adjusted for the convenience of
the operative. Make sure that the handle fixings are tight and the dirt
collection hopper is properly seated within the main body of the sweeper.
Work methodically up and down the area to be swept, ensuring that each
'pass' overlaps the previous one. To ensure the efficiency of the brushes,
push the sweeper at a good, even pace. To capture larger pieces of debris
the basic clearance of the sweeper can be raised a further 20mm by rotating
the height adjuster seen in fig.1 clockwise. Check the hopper regularly by
lifting it out. Empty it if required. Place it back into the sweeper as shown in
fig.2. Periodically, clean the exterior of the sweeper with a damp cloth.
3. ASSEMBLY & USE
Ensure that the sweeper is only used on hard/dry surfaces.
Ensure that the dirt collection hopper is present and properly
seated before commencing sweeping.
The sweeper is for indoor use only.
Do not leave the sweeper unattended, where it could become a
hazard to other people or traffic in the sweeping area. For
example, in a warehouse situation.
Do not allow anyone to ride on the sweeper.
Do not use the sweeper for any purpose other than that for
which it was designed.
Do not use the sweeper to clear up hazardous materials or any
material that may attack the plastic chassis of the sweeper.
Do not use the sweeper on wet surfaces.
Suitable for maintaining any hard floor and ideal for removing dirt,
dust and debris from large surface areas. Features 4-brush system
with two side brushes and two further brushes set underneath the unit
to easily lift debris into the hopper. Fitted with tubular handle and
adjustable castor wheel that raises the sweeper 20mm enabling
larger pieces of debris to be swept up.
Model No................................................................................. FSW80
Operating Width ....................................................................... 800mm
Hopper capacity ............................................................................ 40ltr
g.1
g.2

01284 757500
01284 703534 [e-mail]
www.sealey.co.uk
Web
email
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
PARTS FOR:
FLOOR SWEEPER 800mm
MODEL: FSW80
ITEM PART NO DESCRIPTION
1 FSW80.01 LOCK NUT (M6)
2 FSW80.02 WASHER
3 FSW80.03 SCREW (ST3.9x16)
4 FSW80.04 ROUND BRUSH
5 FSW80.05 PULLEY
6 FSW80.06 SCREW (3.9x18)
7 FSW80.07 BRUSH SUPPORT
8 FSW80.08 BEARING (608)
9 FSW80.09 BEARING COVER
10 FSW80.10 SPINDLE FOR ROUND BRUSH
11 FSW80.11 BEARING COVER
12 FSW80.12 SCREW (ST3.9x12)
13 FSW80.13 SCREW (M4x16)
14 FSW80.14 ROLLER CONNECTOR
15 FSW80.15 SCREW (ST3.9x25)
16 FSW80.16 ROLLER SUPPORT (RIGHT)
17 FSW80.17 PUNCH BEARING
18 FSW80.18 BELT PULLEY
19 FSW80.19 SPINDLE
20 FSW80.20 RUBBER BELT (6x525)
21 FSW80.21 WHEEL COVER
22 FSW80.22 WHEEL
23 FSW80.23 HEX SCREW (M10x65)
24 FSW80.24 SPRING WASHER
25 FSW80.25 WASHER
26 FSW80.26 STEEL COVER
ITEM PART NO DESCRIPTION
27 FSW80.27 INNER WHEEL
28 FSW80.28 SPINDLE
29 FSW80.29 WASHER
30 FSW80.30 RUBBER BELT (6x880)
31 FSW80.31 SCREW (M6x8)
32 FSW80.32 METAL FIXING (RIGHT)
33 FSW80.33 NUT (M10)
34 FSW80.34 CASTOR WHEEL
35 FSW80.35 WHEEL HOLDER
36 FSW80.36 ADJUDTMENT SPINDLE
37 FSW80.37 BODY
38 FSW80.38 BOLT (6x50)
39 FSW80.39 HEIGHT ADJUSTABLE SWITCH
40 FSW80.40 COLLECTION TRAY (UPPER)
41 FSW80.41 COLLECTION TRAY (LOWER)
42 FSW80.42 HANDLE FOR COLLECTION TRAY
43 FSW80.43 HANDLE, UPPER
44 FSW80.44 SCREW (M8x30)
45 FSW80.45 HANDLE FIX NUT
46 FSW80.46 HANDLE, LOWER
47 FSW80.47 ROLLER BRUSH COVER
48 FSW80.48 METAL FIXING (LEFT)
49 FSW80.49 RUBBER BELT (6x1120)
50 FSW80.50 ROLLER SPINDLE
51 FSW80.51 ROLLER SUPPORT (LEFT)
52 FSW80.52 ROLLER BRUSH
Issue: 1
Issue Date: 290911