Sealey MES03 User manual

100KG ENGINE REBUILD STAND - MULTICYLINDER
MODEL NO: MES03
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure all Health and Safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
8DO NOT use unit if damaged.
9Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9Keep the stand clean for best and safest performance.
9Locate the stand in a suitable work area. Keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
9Use on a firm, level surface capable of sustaining the stand and the load.
9Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9Ensure all non-essential persons keep a safe distance whilst the stand is in use.
9Lock ratchet in position with locking pin before fixing a load and ensure the engine is centred and securely mounted.
9Ensure the stand and load are stable.
9DO NOT allow untrained persons to use the stand.
8DO NOT exceed the rated capacity.
8DO NOT use the stand for purposes other than those for which it is designed.
9When not in use store stand in a safe, dry, childproof area.
2. INTRODUCTION
Suitable for supporting large multi-cylinder engines (maximum weight 100kg). The supports can rotate for accessibility to all parts of the engine.
Width and length adjustable. Engine stand’s frame elongates to allow adjustment for length between mounting points.
3. SPECIFICATION
Model no: .................................................................. MES03
Maximum capacity: ...................................................... 100kg
Height: ....................................................................... 480mm
Length:....................................................................... 970mm
4. ASSEMBLY
4.1. Assemble as Parts Diagram overleaf and ensure
 xingsaresecure.
5. OPERATION
Numbers refer to Parts list overleaf.
5.1. Adjust width of frame to suit engine and tighten locking
bolts (17).
5.2. Use original engine mounting bolts or studding,
washers and nuts of appropriate size to secure the
engine to the stand, using supporting frames (11).
5.3.  Ensureallxingsandscrews(9)thatsecuresupporting
frames (11) and locking bolts (17) are tight before
rotating engine.
5.4. Be aware of centre of gravity shifting as an engine is rotated.
5.5. Take the weight of the engine (the help of a second person may be needed) before releasing the ratchet bolt (1).
6. MAINTENANCE
6.1.  Periodicallychecktightnessofallxings.
6.2. Keep frame clean (do not use solvents).
Y
MES03| Issue 1 19/12/19
Original Language Version
© Jack Sealey Limited
Refer to
Instruction
Manual

Original Language Version
© Jack Sealey Limited MES03| Issue 1 19/12/19
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.