Sealey BS103 User manual

WORKSHOP BICYCLE STAND
MODEL NO: BS103
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Maintain the stand in good condition, replace or repair damaged parts. Use recommended parts only. Non authorised parts may be
dangerous and will invalidate the warranty.
9Before use ensure that all stand nuts, bolts and clamps are tight and that moveable and clamping parts are in good working order.
9Place stand on a sound, level surface offering adequate working clearance for its function.
9Keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting.
9 Removeillttingclothing.Removeties,watches,rings,andotherloosejewellery,andcontainlonghair.
9  Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
9Keep children, pets and unauthorised persons away from the working area.
8 DO NOT use the stand for any purpose other than for which it is designed.
8 DO NOT get the stand wet or use in damp or wet locations or areas where there is condensation. 
9When not in use, store the stand in a safe, dry, child proof area.
9Avoid damage to the bicycle frame and cables etc. when tightening clamps.
8DO NOT exceed the maximum load of 30kg.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack
of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
2. INTRODUCTION
Adjustableworkheightandfittedwitharticulatedrubbercoatedframeclamppreventingdamagetopaintwork.Featuresfourfoldinglegswitha
1370mm span for added stability and multi-position tool tray to ensure tools are always close to hand.
3. SPECIFICATION
Model no: .................................................................... BS103
Minimum working height:.......................................... 1050mm
Maximum working height:......................................... 1750mm
Maximum load:............................................................... 30kg
Minimum cycle frame size............................................ 25mm
Maximum cycle frame size ........................................... 40mm
Frame tube diameter:......................... inner pipe:Ø35x1.5mm
...........................................................outer pipe:Ø38x1.2mm
4. OPERATION
4.1. Release the quick release clamp (1) hold the tube (A) and push down on the clamp
so that the legs spread out fully. Tighten the quick release clamp. The legs can be
spread out less wide, but this may compromise the stability of the stand, depending
on the position/weight of the cycle when mounted on the stand.
4.2.  Ensurethefourfeet(2)areplacedatontheoorsurface,whichshouldbestable
  andlevel.Thestandcanbepermanentlyxedtotheoorifrequired.
4.3. Insert the telescopic shaft (B) into tube (A) and lock into place.
4.4. Attach the bike support clamp head (C) onto the telescopic bar.
4.5. Attach the tool storage tray (D) to the tube (A) and tighten the two hex. bolts.
4.6.  Checkallxingsforstabilityandadjustand/orre-tightenthemifnecessary.
4.7. Lift a cycle onto the stand, making sure that it is mounted centrally for maximum
stability and to avoid straining the clamp.
4.8. Secure it on the stand by positioning the top frame tube into the clamp and
  tighteningitusingthequickreleaseclamp(g.2).
4.9.  Toadjusttheangleofthecycle,itisadvisabletoremovethecyclefromthestand
  andtomaketherequiredadjustments.Ifadjustingwiththecyclestillmountedon
the stand, it is recommended that two people are utilised.
4.10. Releasetheadjustmentclampjustenoughsothatthecyclecanbemovedtothe
required angle and then re-tighten the clamp.
BS103|Issue:3(2,F)04/06/20
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Fig.1

8DO NOT exceed the maximum extension height of shaft (B), there is a mark on the shaft.
4.11. Always ensure that after repositioning the cycle on the stand, that the stand/cycle are stable before carrying out any work.
4.12. After use, clean the stand, if required, with warm water and then dry with a clean cloth. Store the stand in a safe, dry, child proof
location.
Original Language Version
© Jack Sealey Limited
Fig.2
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
BS103|Issue:3(2,F)04/06/20