Sealey SM27ST.V2 User manual

FLOOR STAND FOR SM27.V2
MODEL NO: SM27ST.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
 WARNING! The lathe (not included) is heavy - it is recommended that two persons lift and lower the lathe onto the assembled stand.
9 Avoidtrappinghands/ngersbeneaththelathe,whenloweringontothestand.
9 Ensurethestandispositionedonrm,levelground(werecommendconcreteorasimilarhardsurface).
9 Ensurethesurroundingenvironmentisnotconducivetorust.Rustwilldamagethestand,renderingitstructurallyunsafe.
2. INTRODUCTION
Suitable for Model no. SM27 metal turning lathe an other similar lathes. Includes suds tray.
3. SPECIFICATION
Model no ............................................................. SM27ST.V2
Weight............................................................................ 50kg
4. CONTENTS
5. a ASSEMBLY
Note: Assemble with fixings left loose in order to align parts
then tighten before use.
5.1. Attach the three hole side of the angle brackets (4) to the
 cabinets(2&3)usingM5x12screws(9),Ø5atwashers(10),
5.2.  Ø5springwashers(11)andtheM5hexnuts(12).
5.3. Attach the kick plate (5) to the two hole side of the angle
 brackets(4)usingM5x12screws(9),Ø5atwashers(10),Ø5springwashers(11)andtheM5hexnuts(12),joiningthecabinets(2&
3) together.
5.4. Place the suds tray (1) on top of the cabinets (2 & 3) and align the screw holes.
5.5. Align the L/H and R/H shim blocks (6 & 7) over the screw holes in the suds tray (1) and the cabinets (2 & 3). Secure into place using
the M6x25 screws (8).
Refer to
instruction
manual
Wear
protective
gloves
SM27ST.V2|Issue:3(H,F)06/06/18
Original Language Version
© Jack Sealey Limited
ITEM DESCRIPTION QTY
1SUDS TRAY 1
2 R/H CABINET 1
3 L/H CABINET 1
4 ANGLE BRACKET 2
5 KICK PLATE 1
6 R/H SHIM BLOCK 150mm 2
7 L/H SHIM BLOCK 200mm 2
8 SCREW M6x25 8
9 SCREW M5x12 10
10 Ø5FLATWASHER 10
11 Ø5SPRINGWASHER 10
12 M5 HEX NUT 10
13 BOLT M10x100 4
14 Ø10FLATWASHER 4
15 Ø10SPRINGWASHER 4
16 M10 HEX NUT 4
fig.1

5.6.  Thelathe(notincluded)issecuredtothestandusingtheM10x100bolts(13),Ø10atwashers(14),Ø10springwashers(15)andthe
M10 hex nuts (16).
6. MAINTENANCE
6.1.  Verylittlemaintenanceisrequired,butregularchecksshouldbemadetoensurethestructuralintegrityofthestand.Thelatheisheavy
 andshouldthestandsustainstructuraldamage,itcouldcollapse/overbalanceifnotproperlyrepaired/replaced.
6.2. Periodically check the stand for rust.
6.3.  Occasionallyremovethelatheandcheckthenuts&screwswithinthestand.Ensuretheyareallpresent,intactandtightened.
6.4.  Regularlycheckthestandfordents,distortionandsignsofmisuse.
6.5.  Forinformationregardingrepairs/replacementcontactyourauthorisedSealeystockist.
6.6.
6.7.
6.8.
6.9.
.
Original Language Version
© Jack Sealey Limited SM27ST.V2|Issue:3(H,F)06/06/18
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycleunwantedmaterialsinsteadofdisposingofthemaswaste.Alltools,accessoriesandpackagingshouldbesorted,takento
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids
according to local regulations.
Note:Itisourpolicytocontinuallyimproveproductsandassuchwereservetherighttoalterdata,specificationsandcomponentpartswithoutprior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
Parts support is available for this product. Please email [e-mail] or telephone [phone]