Sealey BS102 User manual

WORKSHOP BICYCLE STAND
MODEL NO: BS102
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited
1. SAFETY
9Maintain the stand in good condition, Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be
9dangerous and will invalidate the warranty.
9Before use ensure that all stand nuts and bolts are tight and that moveable and clamping parts are in good working order.
9Place stand on a sound level surface offering adequate working clearance for its function. Keep area clean, tidy and free from
unrelated materials. Ensure there is adequate lighting.
9When mounted ensure the bicycle centre of gravity is between the stand legs.
9 Removeillttingclothing.Removeties,watches,rings,andotherloosejewellery,andcontainlonghair.
9 Maintaincorrectbalanceandfooting.Ensuretheoorisnotslipperyandwearnonslipshoes.
9  Keep children and unauthorised persons away from the working area.
8DO NOT use the stand for any purpose other than for which it is designed.
8DO NOT get the stand wet or use in damp or wet locations or areas where there is condensation.
9When not in use store the stand in a safe, dry, child proof area.
8DO NOT exceed maximum load of 30kg.
2. INTRODUCTION
Manufactured with steel tubes with rubber coated frame clamp which helps prevent damage to
paintwork. Features large rubber feet for added stability and multi-position tool tray to ensure tools
arealwaysclosetohand.Adjustableworkheightfrom1050mmto1750mm.
3. SPECIFICATION
Model no ..................................................................... BS102
Max. height .............................................................. 1750mm
Min. height ............................................................... 1050mm
Max. load ....................................................................... 30kg
Min. cycle frame size.................................................... 25mm
Max. cycle frame size................................................... 40mm
Frame tube diameter.......................... innerpipe:Ø35x1.5mm
......................................................outerpipe:Ø38x1.2mmGS
4. ASSEMBLY
4.1. Assemblebaseinserting2radiallegsandslidingrearlegthroughbasemounting 
andclampingitatitsmid-point(g.1.Aandg.2).Securebytighteningthehexbolts
withthe5mmhexkeysupplied.
4.2. Ensure that the base is placed on a solid, level surface. Fit rubber feet and ensure that they
allhavetheiratsurfacedownwards.
4.3. Inserttheuprighttube(g.1.B)inbaseandsecure.
4.4. Clampmountinghead(g.1.G.)ontoslidingtube(g.1.C.)
4.5. Fix holding clamp (g.1.G.)toshorttube(g.1.F.andg.4).Slidetubeintomountingheadandtightenlockingscrew.
4.6. Attachthetooltray(g.1.E)totheuprighttubeandsettoaconvenientheight.Thetooltraycontainsamagnettoretaintoolsandparts.
BS102Issue:2(H,F)04/06/20
fig.2
fig.1
fig.3
fig.4

Original Language Version
© Jack Sealey Limited
5. USING THE STAND
5.1. Ensure that all hex bolts are tight before using the stand.
8DO NOTexceedthemaximumextensionofthecyclemountingtubes(g.1C&F).Thereisamarkoneachtubetoshowthislimit.
5.2. Only use the stand with cycle suspended over the legs.
5.3. Select a point on the cycle frame which will allow it to be clamped in a balanced position to avoid straining the clamps
or tipping the stand.
5.4.  Adjusttheanglesoftheclamps(fig.4)beforeinstallingcycle.
5.5. Thepressureexertedbytheclampmaybeadjustedbytighteningorlooseningthewingnutunderneath.(fig.4)
5.6. Ifanyadjustmentisrequiredwiththecycleinsitu,itisrecommendedthat2peopleareused.
8DO NOT nip any cables or wires in the clamp to avoid damage.
8DO NOT over tighten clamp on carbon fibre or thin aluminium frames; the clamp can exert considerable force.
5.7.
5.8.
.
BS102Issue:2(H,F)04/06/20
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceableandrequiresdisposal,drainanyfluids(ifapplicable)intoapprovedcontainersanddisposeoftheproductandfluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
Partssupportisavailableforthisproduct.Pleaseemail[e-mail]ortelephone01284757500