Sealey API10 User manual

VICE MOUNTING PLATE FOR API SERIES
WORKBENCHES
MODEL NO’S: API10
Instructions not provided with product online only.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
I
MP
PO
R
RTA
A
NT
:
PLEA
S
E READ THE
S
E IN
S
TRU
C
TI
O
N
S
C
AREFULLY. N
O
TE THE
S
AFE
O
PERATI
O
NAL RE
Q
UIREMENT
S
, WARNIN
GS
&
C
AUTI
O
N
S
. U
S
E
TH
HE
P
PR
O
ODU
CT
COR
REC
TLY AND WITH
CA
RE
FOR
THE P
URP
OSE
FO
R W
HIC
H IT I
S I
NTENDED. FAI
LUR
E T
O D
O S
O M
AY
CAU
SE
DAM
AGE
AN
D/O
R
PE
ER
S
SON
N
AL IN
JU
RY AND WILL INVALIDATE THE WARRANTY. KEEP THE
S
E IN
S
TR
UC
TI
O
N
S
S
AFE F
O
R F
U
T
U
RE
US
E.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
workbench.
WARNING! Use workbench on level and solid ground, preferably concrete. Avoid tarmacadam since the workbench may sink into the
surface.
Locate workbench in a suitable working area.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep the workbench clean and tidy in accordance with good workshop practice.
Keep children and unauthorised persons away from the working area.
DO NOT use the workbench for any purpose other than that for which it is designed.
DO NOT undertake work on the workbench without the workpiece being adequately secured. Use clamps or a vice (not included) to secure
the workpiece. Available from your Sealey stockist.
DO NOT use the workbench out of doors.
DO NOT get the workbench wet or use in damp or wet locations or areas where there is condensation.
DO NOT clean the workbench with any solvents which may damage the work surface or the painted surfaces.
Note! The assembly of this product will require assistance.
2. INTRODUCTION
Mounts onto any of the three workbenches in this range and allows vice to be stored out of the way when not in use, leaving a full free work
surface. Compatible with Model No’s API1500, API1800 and API2100. Vice not included.
3. SPECIFICATION
Model no .................................................................. API1500
Size (W x D x H) ...................................1500 x 750 x 850mm
Weight......................................................................... 56.9kg
Model no .................................................................. API1800
Size (W x D x H) ...................................1800 x 750 x 850mm
Weight....................................................................... 66.68kg
Model no .................................................................. API2100
Size (W x D x H) ...................................2100 x 750 x 850mm
Weight......................................................................... 80.2kg
4. CONTENTS
4.1. Refer to fig.1
Refer to
instruction
manual
Original Language Version
© Jack Sealey Limited
fig.1
API10 Issue 1 28/04/21

Original Language Version
© Jack Sealey Limited
5. WORKBENCH ASSEMBLY
5.1. Refer to fig.2
Join the two leg frames (2) together using one of the upper beams (3) and four short screws (5). Ensure that the open sections on all
components are facing inwards. Fix the second upper beam (3) in place using four short screws (5). Align the fixing holes in the lower
beam (4) with the holes in the two leg frames and fix in place using four short screws (5).
5.2. Refer to fig.3
5.2.1. Lay the bench top (1) face down on a smooth clean surface. Invert the assembled frame and place it centrally onto the bench top. Align
the holes in the upper beams with the holes in the underside of the bench top and fix the frame onto the bench top using six short screws
(5).
5.2.2. Turn the assembled bench onto its feet.
5.2.3. Site the bench in the workplace observing the advice given in section 1.
5.2.4. Adjust the feet to compensate for uneven surfaces and lock each foot using the locking nut shown in fig.2.A.
6. BACK PANEL ASSEMBLY
6.1. Refer to fig.4
Back panel kits are available for all three sizes of bench and are
an optional extra to be purchased separately.
APIBP1500: Back panel assembly for API1500
APIBP1800: Back panel assembly for API1800
APIBP2100: Back panel assembly for API2100
6.2. Take the three back panel supports and clamp them to the back edge of the
bench ensuring that a clamping plate is inserted between the clamping knob
spindle and the underside of the bench top as shown in fig.5. Adjust the
positions of the uprights until the tool panels can be slotted into position
followed by the bin panels above them as shown in fig.4 . On the outer
uprights the back panels should occupy the inner line of slots leaving one
row of slots visible.
7. SHELF ASSEMBLY
7.1. Refer to fig.6
Three widths of shelf unit can be purchased as an optional
extra to match the three back panel kits. The shelves hook
into the outer uprights as shown in fig. 5 and stand away from
the panels slightly allowing them to be put at any height.
API11: Shelf for APIBP1500
API12: Shelf for APIBP1800
API13: Shelf for APIBP2100
fig.2
fig.3
fig.2A
fig.4
fig.5
fig.6
API10 Issue 1 28/04/21

8. VICE MOUNTING CLAMP ASS’Y
8.1. A Vice Mounting Clamp API10 can be purchased as an optional extra to provide a base plate to which a vice can be mounted. The
mounting clamp also allows the vice to be stored out of the way, below the bench, when a full free work surface is required.
8.2. Fig.7 below shows the clamp in the stowed away orientation. The mounting bars have to be removed from the clamp and positioned
under the bench as shown in fig.8-V. Place each bar in a diagonal orientation under the bench top then turn it so that the ends
are over the upper beams. Allow the slots in the ends of the mounting bars to rest over the upturned edges of the beams.
8.3. The main clamp is attached to a tube which is a sliding fit inside
the main mounting tube. Withdraw the clamp from the mounting
tube and fix the mounting tube to the two bars ‘V’, under the
work top using four short bolts as shown in fig.9.
8.4. Insert the clamp tube into the mounting tube as shown in fig.10-Y and rotate the clamp so that it is uppermost. Push the clamp tube into
the mounting tube until the clamp comes up against the edge of the bench and laps over the top of it as shown in fig.11.
8.5. Loosen and remove the four bolts on the front of the clamp and lift the top plate away. Bolt the chosen vice to the top plate ensuring that
the fixings are within the depth of the plate. Place the vice and plate back onto the top of the bench over the lower part of the clamp and
bolt the two parts back together again. Tighten the clamping knob on the underside of the clamp assembly. See fig.10-Z.
8.6. To stow the vice under the bench loosen the clamping knob
on the underside of the clamp assembly. See fig.10-Z. Keeping
a firm hold on the assembly pull the vice and top plate forwards
until they are clear of the bench edge. Allow the assembly to
slowly rotate through 180º until it is hanging downwards.
Push the assembly under the front edge of the bench until it is
in the orientation shown in fig.7.
fig.7
fig.8
fig.9
fig.10
fig.11
Original Language Version
© Jack Sealey Limited API10 Issue 1 28/04/21

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
9. DRAWER OPTIONS
9.1. Drawer units can be purchased as an optional extra. Single and double drawer units can be suspended from the underside
of the bench using two draw support bars as shown in fig.12 Larger drawer units will be free standing under the bench. See below for
other drawer options.
fig.12
API8 Single draw unit (bench mounted).
API9 double drawer unit (bench mounted).
API5655A Five drawer unit(Free standing) (Free standing) API5655B Five drawer unit
Original Language Version
© Jack Sealey Limited
(Free standing) (Free standing)
API5656 Six drawer unit API7238 Eight drawer unit
API10 Issue 1 28/04/21