SeaView SM-14-F User manual

INSTALLATION
INSTRUCTIONS
For Seaview Mast Mount:
SM-14-F
WWW.SEAVIEWGLOBAL.COM
Refer to website for most up to
date instructions and videos.

PARTS INCLUDED
x1
x1
x1
1
SMMBL-2
x1
SMMBR-2
x1
X2
X2
X3
X10
X12
X4
X14
X1
X1X1 X2
¼-20 x 1”
x4x8
5/16 x 1”

5/16” = 8mm 3/16” = 4.7mm
15/16” = 25mm
Tef-Gel or Equivalent
TOOLS NEEDED
Sudbury Elastomeric Marine Sealant
is recommended. To purchase call
800-655-7922 or visit
www.seaviewglobal.com
2

SM-AD-ISO
1A
1B
3
2SM-14-F Mast Mount foot assembly.
Stainless
steel washer
Nylon washer Long nylon
shoulder
washer
Long nylon
shoulder
washer

x8
Apply marine adhesive sealant to the eight shoulder washers, then
insert them into the mast mount as shown.
Once all shoulder washers are inserted attach the two mast mount
feet.
3
4
4
x2
x2
3/8-16 x 5”
3/8-16
Insert the two bolts along with the three washers, two nuts and
lanyard as shown below.
5

Once the feet are attached,
place the assembly onto the
mast.
Make sure the assembly is
level, then mark the top and
bottom bolt hole with a pen.
6
7
5
Once you’ve marked the four
holes use a 3/16” drill bit to
drill into the mast.
8

Using a 25mm hole saw, drill
into the center of the mast
to run our electronic cables.
9
10
6
Apply Tef-Gel to the
four holes you drilled
for the mast mount
feet. Again be sure not
to apply too much.
11
Apply marine adhesive
sealant in the hole you
just drilled. Be sure
not to apply too much.
Then insert the rubber
grommet.

Secure the mast
mount assembly to
the mast using the
supplied rivets.
Using a 3/16” drill bit
drill the remaining
eight holes in the mast
mount feet.
12
13
Apply Tef-Gel to the
eight holes you just
drilled.
14
7

Insert the rivets into
the remaining eight
holes.
Mark two holes for the
latch.
15
16
Using a 3/16” drill bit
drill the two spots you
just marked.
17
8

Apply Tef-Gel to the
two holes.
Secure the latch with
two rivets.
18
19
x8
5/16 x 1”
Use the eight 5/16 x 1” bolts to secure the adapter plate to the
body of the mast mount.
20
9

1/4-20
x4
Insert the four 1/4-20
nuts into the adapter
plate.
Place the drill template onto the adapter plate and mark the
appropriate holes for drilling. Refer to the last page to nd out
which holes you need to drill.
21
22
10
Drill the holes that you
just marked.
22

M6 x 16
M6
x6
Secure the thermal
camera to the adapter
plate with the six
M6x16 bolts and
washers.
23
11

Secure the assembly
with the four 1/4-20 x
1” bolts.
24
1/4-20 x 1”
x4
12

Drill Template Chart
1 ACR RCL75
2 GOLIGHT 2000 / 2020
3 GOLIGHT Striker
4 FLIR, Raymarine M-Series, T300, T400 Series
5 Garmin 2000 / 2020
6 ACR RCL100
7 FLIR, Raymarine MD Series, T200 Series
13

THIS PAGE INTENTIONALLY LEFT BLANK.
14

Tel: [phone]
www.seaviewglobal.com
EUROPEAN OFFICE
Tel: [phone]
www.seaviewprogress.com 4-010819