Sebart Mini Avanti 1.4m ARF User manual

SebArt professional line
Mini Avanti 1.4m ARF
EDF or P20 micro-turbine
ASSEMBLY MANUAL
The all new Mini Avanti Jet 1.4m ARF was designed b Ital
aerobatic pilot Sebastiano Silvestri. This sport ARF jet-model
design is based on Hawk real aircraft design and modifided adding
the ultimate aerod namicall ideas of the modernst pattern models
and using the 15 ears experience in fl ing jets of Seba.... the
result is surprising!
This innovative design combined with the lightweight structure,
the fiberglass fuselage and all wood airframe wings and stabs, give
the Mini Avanti Jet 1.4m ARF an impressive precision and
smoothness at an airspeed and flight condition. Thanks of his low
wingload and the powerfull 90mm 12 blades EDF or the P20
micro-turbine, it can be a fantastic aerobatic jet-trainer… let ou
surprise from our new Mini Avanti Jet ARF !
.....t e only aerobatic-fun limit is your fantasy!
Specifications:
Wing span: ……………..1360 mm
Length:………………… 1420 mm
Wing area:…………….. 38 sq. dm
Radio:….. 6+ ch. + 7 MG sub-micro servos
(3 servos for doors and steering are included with the kit and factor installed)

Weig t wit recommended power set up:
EDF:
Weight (less batter ): 2.900g
Weight RTF (with 5800-6S): 3.800g
90mm 12 blades aluminum EDF unit, 1750 Kw motor, 130A ESC with 8A bec 5V
Micro-turbine P20:
Weight (empt , less RX and Turbine batter ): 3.050g
Weight RTF (with 800-2S RX batt. and turbine batt. + 650cc tank full): 3.700g
conversion turbine set (include tank, trust tube and other accessories) is available as
optional (item # A140-17)
Required radio system:
• Minimum 6-channel radio s stem (better 9ch)
• 7 micro servos 17g. for elevators, ailerons, flaps and rudder
• 3 servos 12g. for doors and steering are factor installed
• full extension set are included in the optional servo set (item # A140-12 set)
Recommended Li-Po batter pack for best performance with EDF:
• 5000-6S or 5800-6S High C-rate
Additional required tools:
• Drill
• Drill bits: 1,5mm
• Phillips screwdriver
• Hobb knife
• Sanding paper
• Masking tape
• Soldering iron
Additional required ad esives:
• thin CA
• medium CA
• epox 5minutes
• epox 20 minutes
• silicon

Warning
This RC aircraft is not a toy!
If misused it can cause serius bodily harm and damage to property. Fly only in
open areas preferably in official flying sites following all instructions included
with your radio and motor.
Before starting assembly
Before starting the assembl , remove each part from its bag and protection for a prior
inspection. Closel inspect the fuselage, wing panels, rudder, and stabilizer for
damage. If ou find an damage or missing parts, contact the place of purchase.
If ou find an wrinkles in the covering, use a heat gun or covering iron to remove
them. Use caution while working around areas where the covering material overlap to
prevent separating the covers.
Warranty information
SebArt garantees this kit to be free from defects in both material and workmanship at
the date of purchase.
This warrant does not cover an parts damage b use or modification, and in no case
shall SebArt’s liabilit exceed the original cost of the purchased kit.
Further, SebArt reserve the right to change or modif this warrant without notice. In
that SebArt has no control over the final assembl or material used for the final
assembl , no liabilit shall be assumed or accepted for an damage of the final user-
assembled product. B the act of using the product, the user accepts all resulting
liabilit .
If the buyer is not prepared to accept the liability associated with the use of this
product the buyer is advised to return this kit immediately in new and unused
condition to the place of purchase.
RADIO SET UP
For a more realistic jet f ing, more stable and eas in the wind, we recommend to
install the SebArt 3 axis gyro system stabilizer for EDF installation or in case of use
the P20 turbine is necessar the installation of the I-GIRO Power Box.

Flaps:
We recommend to use flaps down for starts and landings to make them shorter and
easier.
Activate the FLAP function in our radio.
For start use approx. 20° flaps down and mix 8% elevator down
For landing use approx. 50° full flap down and mix 20% elevator down
Control t rows:
For the AILERON we recommend the following throws:
Use approx. 10% aileron differential (more up) for normal flight.
High rate: 30° left & right
Normal flight: D/R: 60% Expo: 10%
Snap, spin: D/R: 100% Expo: 40%
Start & landing: D/R: 100% Expo: 40%
For the ELEVATOR we recommend the following throws:
High rate: 35° up & down
Normal flight: D/R: 50% Expo: 40%
Snap, spin: D/R: 100% Expo: 80%
Start & landing: D/R: 100% Expo: 80%
For the RUDDER we recommend the following throws:
High rate: 35° left & right
Normal flight: D/R: 80% Expo: 20%
Snap, spin: D/R: 100% Expo: 60%
Start & landing: D/R: 100% Expo: 60%
Note: the Expo is (+) for JR s stems, and (–) for Futaba s stems.
Mixing:
We recommend the following mix (if ou have a programmable computer radio):
Rudder →Elevator DOWN
full rudder to the right, the elevator have to go down (negative) approx. 4%
full rudder to the left, the elevator have to go down (negative) approx. 4%
Rudder →Ailerons
full rudder to the right, the ailerons have to go left approx. 7%
full rudder to the left, the ailerons have to go right approx. 7%

Recommended Center of Gravity
The recommended CG is 145mm behind the leading edge of wing.
Pre-flig t
Never attempt to make full throttle dives! This model have to be flown like a full-
scale airplane. If the airframe goes too fast, such as in a high throttle dive, it ma fail.
Throttle management is absolutel necessar .
Range test your radio
Before fl , be sure to range check our radio as manufacturer’s instruction
manual of ou radio-s stem recommend.
Double-check all controls (aileron, flaps, elevator, rudder and throttle)
move in the correct direction.
Be sure that our motor batter pack is full charged, as per the
instructions included with our batteries and that our radio is full
charged as per its instructions.
Finally... ave nice flig ts!
SEBART International S.r.l.
Via L. Tabellione, 1
47891 Rovereta - Repubblica di San Marino (RSM)
www.sebart.it