ENFORCER PASSIVE AUDIO BALUN
4SECO-LARM U.S.A., Inc.
Standard Baluns Snap-in Baluns
MAE-P115-01Q MAE-P215-01Q MAE-P127-02Q
Max. range 5,900 (1800m) 590’ (180m) 4,920’ (1500m)
Bandwidth 20Hz to 20Khz DC to 25Mhz 60Hz to 20KHz
Insertion loss 0.6 dB 0.3 dB 1.0 dB
Return loss 6.0 dB 25.0 dB -15.0
Common mode
rejection 94.0 dB at 1Khz 42.0 dB at 1Khz 50.0 dB at 1Khz 60.0 dB at 1Khz
Power No power required for audio
Connections
Wire type UTP (unshielded twisted pair)
Wire category 20 - 24 AWG @ screwless terminal blocks
Cat2 or better, Cat5 ideal, Cat6 improves range
Connectors In Gold-plated RCA
Out Terminal block RJ-45 Connector (pin 7-, pin 8+)
Other
Dimensions 2
1
/
4
” x
5
/
8
” x
9
/
16
” (57 x 16 x 14 mm) 2” x
7
/
8
” x
3
/
4
” (51 x 22 x 19 mm)
Temperature Range 32° ~ 131° F (0° ~ 55° C)
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only,
at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE: The information and specifications printed in this manual are current at the time of publication. However, the
SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in
whole or in part, without the written permission of SECO-LARM.
SECO-LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
E-mail: sales
@
seco-larm.com
mi-EVT-PH4-V2WOQ.docx
PITLW2
Specifications:
Troubleshooting:
No sound •Check to make sure polarity is correct
•Make sure the maximum distance of the UTP does not exceed the
maximum range of the balun
•Make sure all connections are snugly in place
•Make sure the RJ-45 connector is wired according to T568B wiring
standards
PITSW4
MANUAL
MAE-P115-01Q
Passive Digital and Analog Audio Baluns
The ENFORCER Passive Audio Baluns are the quick, low-cost way to connect audio devices at
greater distances than traditional audio cabling methods. The audio baluns work in pairs to allow
digital and analog audio signals to be transmitted over low-cost Cat5e/6 unshielded twisted pair
(UTP) cable instead of costly coax cable.
Passive operation – No external power
required
•Uses low-cost Cat5e/6 cable instead of costly
coax cables
•Small size for easy installation
High immunity from interference – Built-in
impedance coupled device and noise filter
•Gold-plated connector for lon
reliability
•Limited lifetime warranty
NOTE: Products with a model number that ends with “Q” or have a round green “Q” sticker represent RoHs compliant products.
MAE-P215-01Q
MAE-P127-02Q
MAE-P227-02Q
Digital Audio Balun (standard)
Digital Audio Balun (snap-in)
Analog Audio Balun (standard) Analog Audio Balun (snap-in)
