SECO-LARM ENFORCER VI-B1003-SBQ User manual

ENFORCER IR Illuminator Manual ENFORCER IR Illuminator Manual
IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LARM will not be held responsible for the use of this product in violation of any current laws or statutes.
WARNING Stop using the illuminator if you see a malfunction like smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
MANUAL
ENFORCER
VI-B1003-SBQ
24-LED IR Illuminator
SECO-LARMSECO-LARM
SECO-LARMSECO-LARM
SECO-LARM®®
®®
®
VIDEO
®
MiIR_Illluminator.PMD
PITNW1
®
Weatherproof
Additional Optional CCTV Connectors
CA-1526-1FQ Single DC jack to double DC plug, 1' wire.
CA-1536-1FQ Single DC jack to triple DC plug, 1' wire.
EVA-F5521-3 Female DC pigtail connector.
EVA-M5521-3 Male DC pigtail connector.
EVA-F5521-T Similar to EVA-F5521-3, but with screw terminal connector.
CA-1616-Q DC plug-to-plug adapter.
CA-1515-Q DC jack-to-jack adapter.
CA-1615-06LQ DC jack to DC plug with LED and 6" wire.
CA-1510-3FLQ Male DC Jack with LED and 3' wire.
CA-1610-3FLQ Female DC plug with LED and 3' wire.
CA-151T-02SQ Male DC jack to terminal block, snap-in, 2.5" wire.
CA-161T-02SQ Female DC plug to terminal block, snap-in, 2.5" wire.
CA-151T-02SLQ Male DC jack to terminal block, snap-in, 2.5" wire, LED.
CA-161T-02SLQ Female DC plug to terminal block, snap-in, 2.5" wire, LED.
CA-171T-02Q RJ45 male to terminal block with 2" cable.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARM®U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: [phone] Fax: [phone]
Website: www.seco-larm.com
E-mail: sales @ seco-larm.com
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.

ENFORCER IR Illuminator Manual ENFORCER IR Illuminator Manual
Dimensions:
Typical
Installation:
A. 1 EV-1323C12DW (or most other IR Cameras) (sold separately)
B. 2 VI-B1003-SBQ IR Illuminator (additional unit sold separately)
C. 1 VB-CF1Q Bracket (sold separately)
D. 1 CA-1536-1FQ (1 DC Jack to 3 DC Plugs.) (sold separately) • Check that the correct power supply is in use.
• Check that the correct power supply is in use.
The illuminator case is hot
IR LEDs do not turn on
TROUBLE SHOOTING
Parts List
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the illuminator within given temperature and electricity limits.
3. Do not aim the LED light directly at the eyes when the LEDs are on.
4. Do not mount the illuminator in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
INSTALLATION
1 . Run a 12VDC power supply wire through the wall to where
the illuminator is to be mounted (if necessary).
2. Assemble the mounting bracket; then screw it into the back of
the illuminator.
3. Hold the illuminator bracket against the wall by hand where it
is to be mounted. Use a pencil to mark the location of the
three screw holes in the bracket.
4. Mount the bracket to the wall using the three included
mounting screws. If the wall is made of dry wall, brick, or
similar material, it may be necessary to use the three
included screw anchors.
5. Do not open or disassemble the illuminator. There are no user-
serviceable parts inside.
6. Do not drop the illuminator or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the CRT, especially when the monitor is turned on
or during de-Gaussing, which occurs automatically with many
monitors when the monitor is turned on.
5. Connect the 12VDC power supply.
6. Adjust the illuminator angle. Loosen and tighten the bracket’s
thumb screw to turn the illuminator and change its angle
relative to the bracket. This ensures the illuminator is pointing
in the right direction.
7. Tighten the bracket’s thumb screw so that the illuminator
does not move, but not so tight that it cracks the case or
bracket.
8. Do a final test of the illuminator.
Type
Enclosure
# of infrared LEDs
Max. LED range
Illumination angle
Power source
Power consumption
Operating temperature
Dimensions
Weight
VI-B1003-SBQ
IR Illuminator
IP67 weatherproof
24
Up to 80 ft.
35°
12VDC±10%
0.05mA (IR off), 210mA (IR on)
14°~131° F (-10°~55° C)
31/16”(L) x 21/4”(D) (78 x 57 mm) (without sunshield)
16 oz. (454g)
Specifications
21/4” (57mm)
211/16” (68mm)
113/16” (46mm)
9/16” (14.5mm)
31/16” (78mm)
29/16” (65mm)
A. 1 x IR Illuminator
B. 1 x Adjustable Sunshield
C. 1 x Mounting bracket
D. 36” cord
E. DC jack
F. Adjustment nut
®
Infrared
Day/Night
ENFORCER
ENFORCER
®
Infrared
Day/Night
C
A
B
E
Gx3
Important:
Do not cut DC jack.
Use SECO-LARM’s
EVA-F5521-3 Pigtail
Connector for easy
installation and
serviceability. D
H
F
G. Mounting holes
H. 1 x DC pigtail connector
3 x Mounting screws
3 x Screw anchors
1 x Manual
D
BBA
C