Seconique Corona User manual

ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped o ffimmediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
CARE AND MAINTENANCE
Page 01
CORONA BAR CHAIR
FOR DOMESTIC USE ONLY
SEC/SH/07/21/KK1

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
01
02
03
04
05
06
S400-404-007-KK1-01 Back Right Upright 11/1
Back Le Upright
Front Right Leg
Front Le Leg
Back Support Rail
Side Seat Rail(260mm)
S400-404-007-KK1-02
S400-404-007-KK1-03
S400-404-007-KK1-04
S400-404-007-KK1-05
S400-404-007-KK1-06
1
1
1
2
2
1/1
1/1
1/1
1/1
1/1
Page 02
SEC/SH/07/21/KK1
FOR YOUR FUTURE
REFERENCE
ORDER NUMBER
SHOULD BE HERE
07 Stretcher(260mm)
S400-404-007-KK1-07 31/1
08
09
10
Front Seat Rail(260mm)
Back Seat Rail(270mm)
Back Stretcher(270mm)
S400-404-007-KK1-08
S400-404-007-KK1-09
S400-404-007-KK1-10
1
1
1
1/1
1/1
1/1
11 Seat Pad
S400-404-007-KK1-11 11/1
11
05
05
02
01
09
06
06
08 03
04
10 07
07 07

Ø 7 x 90
FITTINGS
TOOLS REQUIRED
Page 03
SEC/SH/07/21/KK1
16
08
12
01
01
04
D
E
F
A
B
C
Ø 7 x 60
GLUE
8,0 x 30
3,5 x 35

A04
Ø 7 x 90
STEP 1
STEP 2
SEC/SH/07/21/KK1
Page 04
06 - x2
SIDE SEAT RAIL(260MM)
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
C16
02 - x1
BACK LEFT UPRIGHT
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
C
Glue must be added to
the dowel holes on
parts 06 and 07.
04 - x1
FRONT LEFT LEG
06 - x1
SIDE SEAT RAIL(260MM)
8,0 x 30
E01
GLUE
E
C
07 - x3
STRETCHER(260MM)
Ø 7 x 60
Ø 7 x 90
A
F
A
A
A
260mm
260mm
E02
06
04
07
07 - x1
STRETCHER(260MM)
Glue must be added to
the dowel holes on
part 02 and 04.
10 - x1
BACK STRETCHER(270MM)
05 - x2
BACK SUPPORT RAIL
C
07
10
06
C
C
C
C
C
C
C
05
x3
x2
x2

Ø7 x 60
B04
STEP 3
STEP 4
SEC/SH/07/21/KK1
Page 05
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
05 - x2
BACK SUPPORT RAIL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A04
Ø 7 x 90
A
F
A
A
A
E
260mm
260mm
03
01
07
06
Ø 7 x 60
Ø 7 x 90
01 - x1
BACK RIGHT UPRIGHT
03 - x1
FRONT RIGHT LEG
06 - x1
SIDE SEAT RAIL(260MM)
07 - x1
STRETCHER(260MM)
Glue must be added to
the dowel holes on
part 02.
B
B
B
B
F
270mm
270mm
Ø 7 x 60
Ø 7 x 90
E
05
05
09
10
09 - x1
BACK SEAT RAIL(270MM)
10 - x1
BACK STRETCHER(270MM)
02
Glue must be added to
the dowel holes on
part 01 and 03.

B
A02
Ø 7 x 90
STEP 5
STEP 6
SEC/SH/07/21/KK1
Page 06
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
Please assemble on
a clean soft surface
to avoid damage.
A02
Ø 7 x 90
A
07 - x1
STRETCHER(260MM)
08 - x1
FRONT SEAT RAIL(260MM)
Ø 7 x 60
Ø 7 x 90
08
07
01
Ø7 x 60
B04
Ø 7 x 60
Ø 7 x 90
B
B
A
B
B
F
260mm
260mm
E
A
F
Glue must be added to
the dowel holes on
part 01.
E
A
F
Glue must be added to
the dowel holes on
part 02.

STEP 7
STEP 8
SEC/SH/07/21/KK1
Page 07
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
D04
11 - x1
SEAT PAD
D
D
D
D
D
(View from underneath)
11
3,5 x 35