Seconique PANAMA LAMP TABLE User manual

Page 01
PANAMA LAMP TABLE
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
After unpacking this product please keep the original packaging in case it needs to be
returned for any reason.
• Please ensure all fittings and parts are present before commencing with assembly.
• We recommend that you lay a blanket or sheet on the floor to avoid damage to both your
floor and the product.
• We strongly recommend that you keep children away from your work area.
• Assemble this product as close to its final position as possible.
• Never drag or push products as this could cause damage to the joints making it inferior.
• Do not place this product next to a radiator or in direct sunlight.
• Wood is a natural product and may expand if subjected to damp and may shrink or crack
if subjected to heat. Therefore it is recommended that room temperature is maintained,
with no sudden temperature fluctuations.
• Make sure any spillage is wiped off immediately.
• Do not place hot or chilled items directly on to the surface, use a place mat or marking
will occur.
• For general cleaning use a duster, and do not use detergents of any kind. However, the
surface will need to be retreated from time to time. This can be done by using block wax
(unperfumed) and rubbing it over the whole item.
• From time to time it may be necessary to tighten fittings, regular inspections should be
carried out.
SEC/SW/02/21/PJ1
FOR DOMESTIC USE ONLY

* Please check contents and read the instructions before commencing assembly.
* Assemble this product following the enclosed instructions carefully.
* Please take care to avoid damaging panels during assembly.
* Use of power tools to assemble this product will invalidate
any claim and damage this product making it unsafe !!!
* Please assemble on a clean soft surface to avoid damage.
Page 02
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
S300-302-018-PJ1-01 Front Frame 21/1
Side Panel
Top Panel
Leg
S300-302-018-PJ1-02
S300-302-018-PJ1-03
S300-302-018-PJ1-04
2
1
4
1/1
1/1
1/1
TOOLS REQUIRED
FITTINGS
2
4
2
4
2
4
2
4
2
2
2
3
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
1
SEC/SW/02/21/PJ1

Page 03
1 - x2
FRONT FRAME
STEP 2
PARTS REQUIRED
HARDWARE REQUIRED
STEP 1
1 - x2
FRONT FRAME
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
A20
2 - x2
SIDE PANEL
Please assemble on
a clean soft surface
to avoid damage.
Ø 8 x 30mm
4 - x4
LEG
Please assemble on
a clean soft surface
to avoid damage.
A
A
A
AA
A
A
A
A
A
2x
2
1
2x
A
B
B
B
B
TOOLS REQUIRED
B08
Ø 3,5 x 35mm
2x
B
4
4
1
SEC/SW/02/21/PJ1

Page 04
STEP 4
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B04
STEP 3
2 - x2
SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
B04
Ø 3,5 x 30mm
Ø 3,5 x 30mm
Please assemble on
a clean soft surface
to avoid damage.
B
B
B
B
B
B
B
B
Please assemble on
a clean soft surface
to avoid damage.
2
2
SEC/SW/02/21/PJ1

STEP 6
STEP 5
TOOLS REQUIRED
HARDWARE REQUIRED
B08
Ø 3,5 x 30mm
Page 05
3
B
B
B
B
BB
3 - x1
TOP PANEL
PARTS REQUIRED
Please assemble on
a clean soft surface
to avoid damage.
B
SEC/SW/02/21/PJ1