Securitytronix ST-IP4VFD-MZL User manual

ST-IP4VFD-MZL
QUICK START GUIDE
www.securitytronix.comwww.nacebrands.com

ST-IP4VFD-MZL QUICK START GUIDE
1
1
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
About This Document
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We will
readily improve or update the products or procedures described in
the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of this
product. UL has only tested for fire, shock or casualty hazards as
outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification
does not cover the performance or reliability of the security or
signaling aspects of this product. UL MAKES NO REPRESENTATIONS,
WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING
RELATED FUNCTIONS OF THIS PRODUCT.

ST-IP4VFD-MZL QUICK START GUIDE
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at their
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the Low Voltage Directive 2006/95/EC, the
EMC Directive 2004/108/EC, the RoHS Directive 2011/65/EU.

ST-IP4VFD-MZL QUICK START GUIDE
3
3
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment,
or dispose of it at designated collection points. For more information
see: www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this symbol,
which may include lettering to indicate cadmium (Cd), lead (Pb), or
mercury (Hg). For proper recycling, return the battery to your
supplier or to a designated collection point. For more information
see: www.recyclethis.info

ST-IP4VFD-MZL QUICK START GUIDE
4
4
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings
are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
● While using this product, you must be in strict compliance with
the electrical safety regulations of the nation and region. Please
refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low
Voltage) and the Limited Power Source with 24 VAC or 12 VDC
according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

ST-IP4VFD-MZL QUICK START GUIDE
5
5
● Do not connect several devices to one power adapter as adapter
overload may cause over-heating or a fire hazard.
● Please make sure that the plug is firmly connected to the power
socket. When the product is mounted on wall or ceiling, the
device shall be firmly fixed.
● If smoke, odor or noise rise from the device, turn off the power
at once and unplug the power cable, and then please contact
the technical support.
Cautions
● Make sure the power supply voltage is correct before using the
camera.
● Do not drop the camera or subject it to physical shock.
● Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period,
please replace the lens cap to protect the sensor from dirt.
● Do not aim the camera at the sun or extra bright places.
Blooming or smearing may occur otherwise (which is not a
malfunction), and affect the endurance of sensor at the same
time.
● The sensor may be burned out by a laser beam, so when any
laser equipment is in use, make sure that the surface of sensor
will not be exposed to the laser beam.

ST-IP4VFD-MZL QUICK START GUIDE
6
6
● Do not place the camera in extremely hot, cold (the operating
temperature shall be-22F~+140F,or -40°F ~ 140°F if the camera
model has an “H” in its suffix), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
● To avoid heat accumulation, good ventilation is required for
optimal operation.
● Keep the camera away from liquid while in use.
● While in delivery, the camera shall be packed in its original
packing, or packing of the same texture.
● Regular part replacement: a few parts (e.g. electrolytic
capacitor) of the equipment shall be replaced regularly
according to their average life span. The average time varies
because of differences between operating environment and
usage.
● Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.
● If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (Securitytronix shall not
assume any responsibility for problems caused by unauthorized
repair or maintenance.)

ST-IP4VFD-MZL QUICK START GUIDE
7
7
Table of Contents
1 Appearance Description ................................................................. 8
2 Installation .................................................................................... 11
2.1 Disassembling ............................................................... 12
2.2 Mounting ...................................................................... 13
2.2.1 Ceiling Mounting ................................................ 13
2.2.2 Ceiling Mounting with Gang Box ........................ 17
2.2.3 Wall Mounting .................................................... 20
2.3 Image and Focus Adjusting ............................................ 23
3 Setting the Network Camera over the LAN .................................. 26
4 Accessing via Web Browser .......................................................... 31

ST-IP4VFD-MZL QUICK START GUIDE
8
8
1Appearance Description
The overview of the network dome camera is shown below.
Figure 1-1 Overview
4
23
1
910
5
6711
8

ST-IP4VFD-MZL QUICK START GUIDE
9
9
Table 1-1 Description
No.
Description
1
Bubble
2
Black Liner
3
Lens
4
Mounting Base
5
Reset
6
Auxiliary Video Output
7
Serial Port
8
Micro SD Card Slot
9
Network Cable
10
Power Cable
11
Audio/Alarm Interface
Press RESET about 10s when the camera is powering on or
rebooting to restore the default settings, including the user name,
password, IP address, and port No., etc.
Some of the models support audio and alarm functions. The
interfaces are shown as follows.

ST-IP4VFD-MZL QUICK START GUIDE
10
10
Figure 1-2 Audio and Alarm Interfaces
Alarm/Audio Cable Interface

ST-IP4VFD-MZL QUICK START GUIDE
11
11
2Installation
Before you start:
Make sure the device in the package is in good condition and all
the assembly parts are included.
Make sure all the related equipment is powered off during the
installation.
Check the specification of the products for the installation
environment.
Make sure the power supply is matched with your required
voltage to avoid damage.
If the product does not function properly, please contact your
dealer or technical support. Do not disassemble the camera for
repair or maintenance by yourself.
Make sure that the wall is strong enough to withstand three
times the weight of the camera.
For the cameras that supports IR, you are required to pay attention
to the following precautions to prevent IR reflection:
● Dust or grease on the dome cover will cause IR reflection.
Please do not remove the dome cover film until the installation
is completed. If there is dust or grease on the dome cover,
clean the dome cover with clean soft cloth and isopropyl
alcohol.

ST-IP4VFD-MZL QUICK START GUIDE
12
12
● Make sure that there is no reflective surface too close to the
camera lens. The IR light from the camera may reflect back into
the lens causing poor image quality.
● The foam ring around the lens must be seated flush against the
inner surface of the bubble to isolate the lens from the IR LEDS.
Fasten the dome cover to camera body so that the foam ring
and the dome cover are attached seamlessly.
2.1 Disassembling
Steps:
1. Loosen the three screws on the edge of the bubble with the screw
driver.
2. Open the bubble and remove the inner black liner as shown in
Figure 2-1.
Figure 2-1 Remove the Bubble and Black Liner
Black Liner
Bubble
Screw Hole

ST-IP4VFD-MZL QUICK START GUIDE
13
13
2.2 Mounting
Ceiling Mounting
Steps:
1. Disassemble the camera. Refer to the section 2.1.
2. Attach the drill template (supplied) to the place where you want
to fix the camera.
3. According to the drill template as shown in Figure 2-2, drill three
screw holes in the ceiling.
Figure 2-2 The Drill Template
4. If you want to route the cables inside the ceiling, drill a cable hole
in the ceiling according to the drill template. Skip this step if you
Cable Outlet
Screw Hole
Drilling Template for Outdoor
Day/Night Vandal-proof Dome Camera
Side Cable Outlet

ST-IP4VFD-MZL QUICK START GUIDE
14
14
want to route the cables on the surface of the ceiling. Refer to
Conduit Installation on the Side for side cable routing.
5. Attach the camera to the ceiling by aligning the holes of the back
box with the holes on the ceiling.
6. Secure the camera with the supplied screws as shown in Figure
2-3.
Figure 2-3 Secure the Camera
7. Route the cables through the cable hole.
8. Connect the video output connector to the monitor. Connect the
power connector to the power supply.
9. Adjust the image and focus. Please refer to the section 2.3 for
more detailed information.
10. Install the inner black liner back to the camera.
11. Install the bubble back to the camera and secure it with screws
as shown in Figure 2-4.
Screw
Back Box

ST-IP4VFD-MZL QUICK START GUIDE
15
15
Figure 2-4 Secure Black Liner and Bubble
Conduit Installation on the Side
If you want to route the cables from side of the camera, you need to
follow the steps below to install a conduit for cable routing.
Steps:
1. Rotate the water-proof plug counterclockwise to remove it from
the camera.

ST-IP4VFD-MZL QUICK START GUIDE
16
16
Figure 2-5 Remove the water-proof plug
2. Route the power cable and network cable through the side outlet
to the conduit.
3. Align and rotate clockwise the conduit to the side outlet tightly.
Figure 2-6 Install the Conduit to the Camera
Water-proof Plug
Side Cable Outlet
Conduit

ST-IP4VFD-MZL QUICK START GUIDE
17
17
For wall mounting, position the side outlet directly downward for
water-proof.
Figure 2-7 Side Outlet Direction
2.2.2 Ceiling Mounting with Gang Box
Steps:
1. Disassemble the camera. Refer to the section 2.1.
2. Install the gang box in the ceiling.
3. Attach the mounting base to the gang box with two screws.
Downward

ST-IP4VFD-MZL QUICK START GUIDE
18
18
Figure 2-8 In-ceiling Mount
4. Route the cables through the hole in the center of the mounting
base.
5. Align the camera with the mounting base.
6. Tighten the screws to secure the camera with the mounting base.
7. Connect the video output connector to the monitor. Connect the
power connector to the power supply.
8. Adjust the image and focus. Please refer to the section 2.3 for
more detailed information.
Mounting Base

ST-IP4VFD-MZL QUICK START GUIDE
19
19
Figure 2-9 Secure Camera
9. Install the inner black liner back to the camera.
10. Align the bubble with the camera.
11. Tighten the screws to secure the bubble with the camera as
shown in Figure 2-10.
Ceiling