Securitytronix ST-D1000P-W User manual

INSTALLATION MANUAL
ST-D1000P-W
Infrared Dome Camera
v1.0 8/4/14 1

PACKAGE CONTENTS
This package contains:
One ST-D1000P-W infrared dome color camera
Mounting Hardware
One installation manual
Note: The ST-D1000P-W requires a minimum 12VDC 200mA power supply such as the
ST-PS12VDC1A or ST-PS12VDC2A.
PRODUCT DESCRIPTION
The ST-D1000P-W is an infrared color dome camera. The camera uses a 1/3” Color CCD sensor
providing 1000TV lines of resolution. The ST-D1000P-W has a 3.6mm lens for optimal viewing. The 3-
axis mount makes this camera very easy to install and position. The 4 infrared LEDs support low light
illumination down to 0 Lux.
SPECIFICATIONS
ST-D1000P-W
Specifications (Typical)
1.
Image Sensor
1/3” CCD
2.
Scanning System
NTSC
3.
Horizontal Resolution
1000TV Lines
4.
Synchronization
Internal, Negative Sync
5.
Minimum Illumination
0 lux B&W
6.
Auto Electronic Shutter
1/60s~1/100,000s
7.
Lens
3.6mm
8.
S/N Ratio
>50dB
9.
IR LED
4 pcs
10.
IR Distance
80ft
11.
IR Power On
CDS Auto Control
12.
Video Output
1.0Vp-p @ 75
13.
Operating Temperature
14F- 113F
14.
Operating Humidity
<95%
15.
Power Requirements
200mA @ 12VDC
16.
Dimensions
4.4”x3”
17. Weight
14.1 oz
v1.0 8/4/14 2

INSTALLATION AND OPERATION
This symbol is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions.
This symbol is intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electrical shock.
CAUTION: To reduce the risk of electrical shock do not remove the cover or back of
this unit. No user serviceable parts are inside.
CAUTION: To prevent electric shocks and risk of fire hazards, do not use other
than specified power source.
1. UNPACKING and HANDLING
Each unit is shipped assembled and factory tested.
Ensure that all accessories are removed from the container before discarding packing material
2. MECHANICAL INSPECTION
Inspect the front and rear of the equipment for shipping damage. Make sure the equipment is
clean, and no connectors are broken, damaged, or loose. If equipment appears to be damaged or
defective please contact your distributor or SecurityTronix at 1-610-429-1511 for assistance.
3. SPECIAL ATTENTION
a. The installer must comply with electrical safety standards. There must be sufficient
space between the camera’s power supply and video line and any high voltage
equipment and/or cables.
b. To help ensure the camera’s life and proper operation do not point the camera
towards the sun or strong light.
c. Do not install the camera in an environment where the temperature is above 113F.
d. Do not install the camera near a magnetic field or a high-power motor.
e. Do not mount the camera near a radiator or heater.
f. Only use a dry cloth to clean the camera. If there is dirt that is difficult to remove wipe
gently with a mild detergent. Never use strong or abrasive detergents.
g. This camera requires a 12VDC 200mA power supply. Using AC power or a power
supply other than specified will damage the camera.
h. Only qualified installers are allowed to install, test and disassemble the camera.
i. The camera is a low voltage product.
v1.0 8/4/14 3

4. WIRING CONNECTIONS
a. Connect the power supply’s DC plug to the camera’s power port.
b. Connect the camera to the monitor with a 75coaxial video cable.
c. Connect power supply’s AC plug to a suitable AC power outlet.
d. Adjust the lens direction according to the required surveillance area and environment.
v1.0 8/4/14 4

5. TROUBLESHOOTING
a. No picture after applying power –(i) check all plugs and cables are securely
connected to the proper connectors; (ii) ensure your power supply is providing the
correct voltage and current.
b. The picture has ripples –(i) check to see if the power supply is experiencing AC ripple, if
so a filter may be required; (ii) determine if the monitor is faulty; (iii) determine if other
peripheral equipment is causing ripple and if so make the necessary adjustments.
c. The picture background continuously changes color –a fluorescent lamp’s magnetic
field may cause color roll, therefore, reduce the number of fluorescent lamps or
increase the distance between the camera and the lamps.
d. The picture appears smeared –(i) the power supply voltage level may be unstable,
therefore, try another power supply; (ii) ensure the cables are correctly connected
and/or the cables are of the correct impedance.
e. Other interference may require a Securitytronix ground loop isolation filter.
f. Additional troubleshooting assistance can be found on-line at www.securitytronix.com in
addition to support from Securitytronix technicians at 1-800-688-9282, option 3, then
option 2.
v1.0 8/4/14 5