SEDONA Sedona Island User manual

SEDONA Island Assembly
Instructions
SEDONA Island Assembly Instructions Part #34269
Rev. A

2
Important Safeguards:
WARNING: Two to three people are needed to set up the island. Failure
to do so may result in injury.
To prevent electrical shock use only a three pronged power estension cord, do not remove the
grounding prong, do not use an adapter. Use an extension cord rated for outdoor service such
as SJTW
To reduce the risk of fire, electrical shock or personal injury follow the instruction contained in
this guide carefully. Do not omit any steps.
WARNING: Do not store or use gasoline or other flammable liquids or vapors in the
vicinity of this or any other appliance.
Plan your island location prior to beginning any set up. The island must be installed and leveled
in its final location. Moving the island once complete is not advised as damage will occur.
Never attempt to lift the island by the counter top as serious damage may occur.
A Level, a Philips and a Slotted Head screwdriver, and an Adjustable Wrench. An Electric drill with a
Philips head fitting is useful for uncrating the panels. A hole drill is needed of you would like to provide an
alternate extension cord or drainage port.
Recommended Tools:

3
Congratulations on your purchase of the SEDONA by LYNXTM island package cooking center.
The fully featured premium outdoor kitchen can be created in no time at all. The Mom Friendly, Dad Ready TM
cooking products are designed with the family in mind. Crafted by the Lynx Grill Specialists at our factory in
Southern California, each Sedona Grill displays the meticulous fit and finish and high-quality material that
have made Lynx products favorites of grilling enthusiasts.
Before you begin the island installation you need to plan ahead. Some things to con-
sider:
POWER SUPPLY:
Where will the power enter your island?
A 1-1/2 hole is provided in the base panel for an extension cord to pass. If another location is desired you will
have to drill a hole into the side or back panels.
The extension cord should be brought into the enclosure before the base is leveled and the side panels assem-
bled.
Can the base be positioned over an existing 110 VAC electrical outlet so an extension cord will not be needed?
Should a qualified electrical technician be provided for this work? It is recommended.
ISLAND ORIENTATION:
From what direction are the prevailing winds coming? It is important for proper operation that winds do not
blow directly on the rear of the grill.
Consider positioning the island to take advantage of natural wind breaks.
LEVELING THE ISLAND:
Can the grill be leveled properly in its final location?
The base has adjustable legs that must be used to level the island before the panels and top are installed.
Is the island installed on solid ground or pavers so the adjustable feet will not sink in over time?
If the island is not leveled correctly the panels will be misaligned and cannot be corrected once assembly is
complete.
Once assembly is completed the island cannot be moved.
ASSEMBLING THE ISLAND:
Do you have an assistant or two to help in the assembly? You will need assistance holding panels in place
while assembling, and for installing the counter top.
The top panel is heavy and we don’t want anyone hurt while assembling the island.
INSTALLING THE APPLIANCES:
The side burner is equipped with 2 drainage tubes. There is a hole in the base panel for these to pass. Plan for
the drain position, can the tubes be positioned to drain properly?
The grill and side burners need proper connections to the gas supply. Do you need a qualified technician to
assemble and leak test the gas connections? It is recommended.
The refrigerator should be leveled during installation and allowed to sit at rest for at least 2 hours before plug-
ging it in.
If you have any questions or comments please contact Lynx Customer Care:
Lynx Professional Grills
5859 Rickenbacker Rd.
Commerce, CA 90040
Lynx Customer Care 888.289.5969

4
1
(14044)
TANK RETAINING
WASHER 1/4 X 11/16
2 EA.
4
(14014)
TRANSFORMER /
BATTERY MOUNTING
SCREWS
8-32 X 3/8 TRUSS
2 EA.
3
(33839)
SIDE BURNER MOUNT-
ING HEX NUT 1/4-20 SS
2 EA
4
(32730)
SIDE BURNER MOUNT-
ING SCREW 1/4-20 X 1-1/4 PH
2 EA.
5
(14012)
ACCESS DOOR FRAME
MOUNTING SCREWS 1/4-20 X 3/8 PH
4 EA.
6
(34295)
HEX BOLT
1/4-20 x 1-1/2” LONG
2 EA.
7
(34264)
TANK RETAINER
FINGER SCREW 1/4-20 x 1-1/2”
2 EA.
8
(34396)
ADJUSTABLE FEET
6 EA.
9
(34395)
WING NUT
3/8-16
10 EA.
10
(34296)
WING BOLT
3/8-16 x 2
4 EA
11
(34333)
COUNTER TOP MOUNT-
ING CLAMP 2 EA.
12
(80758)
ACCESS DOOR FRAME
MOUNTING BRACKET
(Note weld nut location)
4 EA.
13
(80759)
SIDE BURNER MOUNT-
ING BRACKET
(Note weld nut location)
2 EA.
14
(34332)
FRONT & BACK
PANEL MOUNTING
CLAMPS
4 EA.
PART NUMBER DESCRIPTION PHOTO SPECIFICATIONS

5
Step 1 Unpacking the Crate
Using a manual, or power Philips head screwdriver, remove
all the screws from the crate. Then remove the bottom, front
and two side panels from the shipping crate.
We recommend 2 to 3 people perform setup op-
erations.
Step 2 Position and Level the Base
Place the island base on a level surface in
it’s final location and proceed to level it in
all directions. The bottom panel has adjusta-
ble feet for this purpose.
DO NOT OMIT THIS STEP. If the base is not lev-
eled correctly the island will be misaligned. The base
cannot be leveled and the island cannot be moved once
the assembly is finished. If you need to reposition the
island you will have to disassemble it and start again.

6
Step 3 Assembling the Rear & Side Panels
Assemble the rear panel to the bottom panel by placing the
corners of the back panel on top of the bottom panel corners
and push them firmly together.
Step 3a
Step 3b
Step 3c
Step 3 Continued
While one person holds the rear panel in place, attach a side panel to
the rear panel loosely using the 2 wing-nuts, turned in about 4 full
turns. This will allow the panel to stay loose enough to align the rest
of the panels and hardware.

7
Step 3 Assemble the Front Panel
With one person holding the rear and side panel in place,
assemble the front panel to the bottom by placing the
front panel corners on top of the bottom panel corners
and pushing them firmly together
Tilt the front edge of the side panel away from the bot-
tom panel to allow the front panel mounting brackets to
pass by threaded mounting screws on the side panel.
Push the side panel into position and attach to the front
panel loosely with 2 wing nuts.
Push the remaining side panel into posi-
tion and attach it to the front and rear pan-
el loosely with 4 wing-nuts. Clamp both
side panels to the front and rear panels
using 4 wing-bolts and clamps. After
tightening the clamps go back and tighten
the 8 wing-nuts to secure the side panels
to the front and back panels.

8
Step 4 Overview of the Island’s Electrical System
Now that the island wall assembly is complete, familiarize yourself with the location of the electrical outlets.
The electric outlets come pre-wired from the factory. The photo below shows the position of the 110 VAC
GFCI outlet on the left rear wall, the back panel center outlet for the refrigerator and grill power supply, and
the combination USB charging station and 110 VAC power outlet on the right.
To prevent electrical shock use only a three pronged power cord, do not remove the
grounding prong, do not use an adapter. Use a UL approved extension cord rated for
outdoor service such as SJTW
Before installing the grill and accessories attach your extension cord into the GFI
outlet. Do not plug the extension cord into a power source until you have completed
the equipment installation.
The island wiring diagram is shown below. If you have any questions please contact
LYNX customer care or consult a professional electrician.
Back Panel Outlet Side Panel USB Outlet
12” 3 - Prong Grounded Pigtail,
Provided
2 Wire, Armored
Conduit with
Ground
Strain Relief at all Connections
USB Outlet
Back Panel Outlet
GFI Outlet
Basic Wiring Diagram
Attach extension cord

9
Step 5 Mounting the Transformer
Locate the 2 transformer mounting screws and the transform-
er/battery bracket. Mount the transformer on the rear panel
support frame near the rear panel outlet using the pre-drilled
holes provided. Install the side burner battery bracket below
the transformer in the same manner. (See page 13)
Screw Location
Step 6 Installing the Drawers and Door
Storage System
These must be installed before setting the coun-
ter top in place to allow access to the storage sys-
tem door frame mounting bracket fasteners.
To simplify the installation, start by removing the drawers
and door. To remove the drawers, find the black lever on
each side glide rail. One lever pushes up and the other one
down to release the drawer from the glides.
The access door simply lifts off of the hinge pins.
Place the storage system frame in the cutout and secure it
with 4 access door frame mounting brackets (Part No. 12
shown below. note the weld nut location), and 4 access
door frame mounting screws (Part No. 4). There are 2 on
each side.
Screw Location

10
Step 7 Install the Countertop
With the help of an assistant or two, place the counter top in
place jiggle it a little until the walls slip into place, and then
secure the top with 2 wing nuts and clamps located under the
counter top, at the front and rear.
Step 8 Install the Side Burner
We recommend a qualified, trained gas service technician per-
form all pipe fitting and gas leak test procedures prior to in-
stalling the refrigerator. Once installed there will be limited
access to the gas piping. Before installing the side burner, fa-
miliarize yourself with the illustration on the next page.
Wrap the side burner manifold threads with Teflon tape, see
Fig. 1 on page 11. Remove the 1/2” FIP fitting from the flexi-
ble hose and install it on the side burner manifold. Attach the
stainless steel flexible hose to the 1/2” FIP fitting at the end of
the side burner manifold.
Set the side burner in place in the counter top cutout. Be sure
to keep the side burner wiring accessible to attach to the grill
once it is installed. Clear plastic tubes are provided to drain
spills and drain water from the side burner. Route the tubes
through the holes in the rear center of the island base for drain-
age out of the island.
On the bottom of the side burner locate the center Philips head
screw on each side of the burner base. Remove the screw and
install the side burner mounting bracket with it (Part No. 13,
note weld nut position) flange up, as shown to the right. Screw
the side burner mounting screw (Part No. 4) into the weld nut,
and install the side burner mounting hex-nut (Part No. 3) on
the screw. Tighten the screw up to the side burner bracket
frame to secure the side burner in place. Use the hex nut to
lock the screw into position.
Step 9 Install the Grill
Locate and remove the plug from the 1/2” Tee fitting in the grill
manifold to facilitate the side burner connection (see the drawing
on the next page).
With the help of an assistant set the grill in place. Make sure to
align the grill evenly and be sure it is fully supported on the
mounting flanges. Before sliding the grill back completely, reach
behind the grill and attach the electrical wiring from the side
burner using the attached Molex connectors (See page 13)

11
Step 10 Making the Connections
We recommend a qualified, trained gas service technician perform all pipe fitting procedures and conduct a
gas leak test prior to installing the refrigerator. Once installed there will be limited access to the gas piping.
Working from the refrigerator cutout, find the stainless steel flexible hose from the side burner. Remove the
1/2” fitting from the flexible hose and wrap the fitting with Teflon tape. Install the fitting into the Tee fitting
on the grill manifold, then connect the flexible gas hose tot the fitting. Tighten all fittings to endure they are
gas tight. Use a leak detection liquid on each threaded joint and check for gas leaks. See the following page
for an alternate leak test method.
Do not check for leaks with an open flame.
Do not use sealant on any flare fittings.
(Fig. 1)

12
Step 11 Installing the LP Tank
The LP Tank retention device can be secured to the door
frame with two 1-1/2” long bolts (provided). The LP
tank is rested in the retainer and the finger screws are
tightened around the base of the tank securing it into po-
sition.
Connect the hose and regulator to the LP cylinder. Make
sure all of the burner knobs are in the OFF position
Step 12 Leak Test All Fittings
Make a solution of 1 part liquid dish soap and 3
parts water being careful not to shake the solu-
tion.
Open the LP Cylinder and using a brush or
spray bottle, apply the solution to all fittings at
the stainless steel connector, the Tee fitting, the
regulator and hose connections
DO NOT CHECK FOR LEAKS WITH
AN OPEN FLAME!
Step 13 Install the Refrigerator
Install the refrigerator and level it according to the refriger-
ator instructions. Route the power cord to the outlet in the
rear panel, but do not plug it in. You must wait 2-3 hours
before plugging it into the outlet on the rear inside panel of
the island.

13
See Step 9
Make the electrical connections as shown below, then plug the transformer into the electrical outlet on the rear
panel.
TO
TRANSFORMER*
These connectors attach to
the battery back up wires on
the grill
*Not actual installation,
illustration is for
demonstration purposes
only.
These connectors attach to
the battery back up wires on
the side burner

14
Lynx Professional Grills
5859 Rickenbacker Rd.
Commerce, CA 90040
Lynx Customer Care 888.289.5969
Fax. [phone]
www.lynxgrills.com