Seedo Auto Grow Home Device User manual

1. Unpack and Install Seedo
2. Install Seedo App
3. Install Seedo Consumables
3.2 Water filter
3.1 CO2 cylinder
3.3 Carbon air filter
Auto Grow Home Device
Quick Install Guide
Initial Installation
• Place Seedo close to power and if possible also
to water supply and drainage.
• Connect power cable to Seedo and plug in.
• Turn On Seedo switch (at back of device).
• Press Seedo’s door opening button at top center.
• Remove all cartons, blue tapes, pink covers on
irrigator pins.
• Download app from App Store or Play Store.
• Read and agree to terms of use and conditions.
• Open service door on top of Seedo.
All the installation videos are available on
the app and can be found also on Seedo’s
Youtube channel.
• Insert cylinder and turn
clockwise as far as possible.
• Do not remove cylinder after
you hear a hissing noise.
• Remove blue cap from the lter.
• Filter is notched and can
only be inserted in one position.
• Push rmly, then turn lter
clockwise until it locks in.
• Remove the plastic lter
cover from its slot by pressing
both sides inwards.
• Insert air lter and replace
plastic cover, ensuring that
snaps are secured in place.

3.4 Fertilizing solutions -
bottles A (green) and B (orange)
3.5 Rockwool slab
Leave space on left
• Connect one end of water hose to tap
and other to water inlet (FILL) at rear of Seedo.
• Ensure hose is fully inserted.
• Open service door, remove water container cap.
Use a funnel and slowly ll the container.
• 4 Gallons (15 liters) of water are needed for initial
watering process. You will need more later on.
Press door opening button,
hold for 15 seconds until it blinks
pale blue.
Dene Seedo name (5-10 alphanumeric
characters and symbols).
Specify which option you selected in step 4
and check that both connections are secure.
• Connect drainage outlet (DRAIN) at rear of Seedo
to home drainage.
• Connect drainage outlet at rear of Seedo to external
container with capacity of 4 gallons (15 liters) at least.
• Insert hose fully into container but above uid level.
Water supply – automatic
Water supply – manual
Drainage – automatic
Drainage – manual
• Press Wi-Fi settings button to open
Settings menu.
• Turn on Wi-Fi and from Wi-Fi Settings
menu, choose UAG XXXX
iOS device:
Type uagpassword and return to app.
Android device:
Approve password uagpassword.
4. Connect Water Supply
and Drainage
5. Connect Seedo to App
6. Connect Seedo
to Your Home WiFi
7. Naming Seedo
8. Choosing Water Source
and Drainage Method
• Open bottle lid.
• Insert suction hose into bottle.
• Insert bottle into its slot
with label facing outwards.
• Lift latch to secure.
• Place slab in tray at bottom of Seedo’s
interior with markings facing downwards.
• Align slab to the right side, away from
water drain mesh on left.
Choose either automatic or manual option
for connection to water supply and drainage.

Pre-planting
• Press Start to choose your growth plan.
• Choose one of the listed categories - one of the names
from the selected category - one of the strains.
• Watch Installing the pH sensor video.
• Remove Rockwool slab from Seedo.
• Open compartment on right of Seedo’s interior.
• The pH sensor is attached to the right side
of the compartment.
• Perform the following actions immediately
before you start the growth plan:
1.Remove tape and take out pH sensor.
2.Unscrew cup from bottom of sensor.
3. Insert sensor in compartment and push rmly into place.
• Replace slab inside Seedo.
• Only when you receive notication to do so,
use a cutter to make 6 incisions in nylon cover.
• Flip slab over.
• Note that the slab is now water-logged,
and is quite heavy and may drip.
• Press OK on the app.
1. Choose Growth Plan
3. Install pH Sensor
5. Prepare Slab for Planting
4. Rockwool Slab Watering
2. Choose Growth Type
After connecting Seedo to the app,
the Main Screen appears showing the name of the device.
Choose Seed or Clone. According to your choice,
the app will explain how to plant your seed/clone.
• It may take some time for Seedo to prepare
its water system for planting; you will receive
notication when it’s done.
• The watering process starts automatically as
soon as you choose the growth plan’s setting
and press Start Growing.
Do not proceed and plant yet.
Wait until slab watering is
completed.
!
!
!
Tip of pH sensor should not be in dry
environment for more than an hour.
Note: Now you will only need to proceed
with steps 3-4. Planting will be done only
when step 5 is completed.

Planting Seeds
Planting Clones
• After ipping slab, use cutter to cut square aps
next to marks in slab’s plastic cover according
to number of seeds to be planted (maximum of 5).
• Make small holes (0.5-1 cm/ 0.2-0.4 in. depth)
in the slab.
• Plant seeds in holes.
• Cover each seed with the remaining
slab material.
• Use sprouting cups to cover each seed.
• After ipping slab, place clone on slab and
use marker to draw a square around clone.
• Move the plant away and at the marked
square cut through the plastic and also layer
of slab underneath it.
• Remove cut slab layer.
• Place clone in hole and ll empty space with
part of slab you removed in previous step.
Now… Let it grow!
!Recommendation:
Use gloves for this process.