SEI Mirage BT7812A0TX User manual

Page |
1
BT7812A0TX/BT7812B0TX
Mirage Double-Door Vanity Sink
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore.com

Page |
2
A) Quantity
of 1
Top Panel
B) Quantity
of 1
Back Splash
C) Quantity
of 1
Left Side Panel
D) Quantity
of 1
Right Side Panel
E) Quantity
of 1
Front Upper Bar
F) Quantity
of 2
Back Upper Bar
G) Quantity
of 2
Back Lower Rail
H) Quantity
of 1
Bottom Panel
I) Quantity
of 2
Door Panel
J) Quantity
of 1
Shelf Panel
1) Quantity
of 11
Large Bolts. Dia:1/4”*1-3/8”L
2) Quantity
of 17
Spring washer
Mirage Double-Door Vanity Sink
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage
.

Page |
3
3) Quantity
of 17
Flat washer
4) Quantity
of 1
Allen wrench
5) Quantity
of 16
Wood Dowel Dia :8*30
6) Quantity
of 4
Knob
7) Quantity
of 4
Small Bolts
Dia.5/32”*1-1/8”L
8) Quantity
of 4
Hinge
9) Quantity
of 24
Screw (Ø3.5*16mm)
10) Quantity
of 2
Metal Plate
11) Quantity
of 6
Medium Bolts Dia:1/4”*5/8”L
12) Quantity
of 4
Shelf Pin
13) Quantity
of 4
Rubber Gasket
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth. Periodically apply
furniture wax to renew the finish. Avoid rubbing or scratching the
surface with rough or abrasive objects.
For replacement parts or
questions, please call SEI
Customer Service at
1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
4
Figure 1
Insert Wood Dowels (5) into
pre-drilled hole on Left Side
Panel (C).
Attach Upper Bars (E/F) to Left
Side Panel (C) with Large Bolts
(1) and Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Figure 2
Insert Wood Dowels (5) into
pre-drilled holes on Left Side
Panel (C).
Attach Bottom Panel (H) and
Back Lower Bar (G) to
assembled unit from Figure 1
with Large Bolts (1) and
Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Mirage Double-Door Vanity Sink
Assembly Instructions

Page |
5
Figure 3
Insert Wood Dowels (5) into
pre-drilled holes on assembled
unit from Figure 2.
Attach Right Side Panel (D) to
assembled unit from Figure 2
with Large Bolts (1) and
Washers (2/3).
Tighten Large Bolts (1) with
Allen Wrench (4).
Figure 4
Attach Back Lower Bar (G) to
Bottom Panel (H) with Large
Bolt (1) and Washers (2/3).
Tighten Large Bolt with Allen
Wrench (4).
G

Page |
6
Figure 5
Attach Knobs (6) to
pre-assembled unit from Figure
4 with Small Bolts (7) and
Rubber Gaskets (13).
Tighten Medium Bolts (7) with
Phillips screwdriver (not
included).
Figure 6
Attach Hinges (8) to Doors (I)
with Screws (9).
Tighten Screws (9) with Phillips
screwdriver (not included).

Page |
7
Figure 7
Attach one Door (I) to
assembled unit from Figure 5
with Screws (9).
Attach Knob (6) to Door (I) with
Small Bolt (7) and Rubber
Gasket (13).
Tighten Small Bolt (7) and
Screw (9) with Phillips
screwdriver (not included).
Figure 8
Attach 2nd Door (I) to
assembled unit from Figure 6
with Screws (9).
Attach Knob (6) to Door (I) with
Small Bolt (7) and Rubber
Gasket (13).
Tighten Small Bolt (7) and
Screw (9) with Phillips
screwdriver (not included).

Page |
8
Figure 9
Insert Shelf Pins (12) into
pre-drilled holes on side
panels.
Place Shelf (J) onto Shelf Pins
(12).
Figure 10
Insert Marble Top (A) into
assembled unit from Figure 9.

Page |
9
Figure 11
Attach Metal Plates (10) to
Back Splash (C) and
assembled unit from Figure 10
with Medium Bolts (11) and
Washers (2/3).
Tighten Medium Bolts (11) with
Allen Wrench (4).
Figure 12
Now your Mirage Double-Door
Vanity Sink is ready for use.
Adjust foot pad to make unit
level as needed.
Note: Install not included piping
items: faucet, drain, and supply
lines to vanity sink according to
the instructions supplied with
those items.
Installation of faucet, drain, and
supply lines by a certified
plumber is recommended.

Page |
10
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas),
Mon-Fri 9am – 4pm CST, or email us at ser[email protected]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019