SEI Carverdale Corner Vanity Sink BT7871A0TX User manual

Page |
1
PO#:
BT7871A0TX/BT7871B0TX
Carverdale Corner Vanity Sink
Assembly Instructions
For assistance with assembly, contact:
Southern Enterprises, Inc.
Customer Service: 1-800-633-5096
[email protected]om
www.seifurniturestore.com

Page |
2
1) Quantity
of 1
Marble top
2L) Quantity
of 1
Left Side Panel
2R) Quantity
of 1
Right Side Panel
3) Quantity
of 1
Faux Drawer Front Panel
4) Quantity
of 1
Bottom Rail
5) Quantity
of 2
Back Top Rail
6) Quantity
of 2
Back Lower Rail
7）
Quantity
of 1
Back Post
8) Quantity
of 1
Bottom Panel
9) Quantity
of 1
Drawer Front Panel
10L)
Quantity
of 1
Drawer Side Left
10R) Quantity
of 1
Drawer Side Right
Carverdale Corner Vanity Sink
Parts List
Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean, padded
surface like carpet or a blanket. Check that you have all parts indicated. Call customer service if any hardware is
missing. Before beginning assembly, carefully study the diagrams below and sort your hardware according to the
pictures. Using the incorrect hardware will cause damage.

Page |
3
11L)
Quantity
of 1
Drawer Back Left
11R) Quantity
of 1
Drawer Back Right
12L) Quantity
of 1
Drawer Vertical Panel Left
12R) Quantity
of 1
Drawer Vertical Panel Right
13)
Quantity
of 1
Drawer Back Panel Middle
14)
Quantity
of 1
Drawer Bottom Panel
15) Quantity
of 1
Top Metal Frame
16L) Quantity
of 1
Front Leg Left
16R) Quantity
of 1
Front Leg Right
17) Quantity
of 3
Back Leg
18) Quantity
of 1
Metal Shelf Frame
A) Quantity
of 16
Cam Bolts
B) Quantity
of 16
Cam Lock
C) Quantity
of 18
Wood Dowel Dia :8*30mm

Page |
4
D) Quantity
of 3
Wood Dowel Dia :6*30mm
E) Quantity
of 9
Wood Dowel Dia :6*20mm
F) Quantity
of 2
Knob
G)
Quantity
of 1
Bolts Dia.5/32”*7/8”L
H) Quantity
of 1
Bolts Dia.5/32”*1-1/2”L
I) Quantity
of 18
Screw Dia.1/8”*1”L
J ) Quantity
of 6
Bolts. Dia:1/4”*1-3/8”L
K) Quantity
of 24
Bolts. Dia:1/4”*5/8”L
L) Quantity
of 32
Flat Washer
M ) Quantity
Of 32
Spring Washer
N ) Quantity
of 1
Allen Wrench
Care and Cleaning Instructions:
Before using, wipe with a clean, dry cloth. Avoid rubbing or
scratching the surface with rough or abrasive objects.
For replacement parts or
questions, please call SEI
Customer Service at
1-800-633-5096.
Assembly Tool Required:
No.2 Phillips Screwdriver
(Not Included)

Page |
5
Do not overtighten cam bolts. Stop when they feel secure.
Figure 1
Insert Cam Locks (B) into
corresponding holes on Faux
Drawer Front Panel (3) and Bottom
Rail (4).
Screw Cam Bolts (A) into threaded
holes on Left Panel (2L).
Attach Left Panel (2L) to Faux
Drawer Front Panel (3) and Bottom
Rail (4) by inserting Cam Bolts (A)
and Wood Dowels (C/D) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 2
Insert Cam Locks (B) into
corresponding holes on Faux
Drawer Front Panel (3) and Bottom
Rail (4).
Screw Cam Bolts (A) into threaded
holes on Right Panel (2R).
Attach Right Panel (2R) to Faux
Drawer Front Panel (3) and Bottom
Rail (4) by inserting Cam Bolts (A)
and Wood Dowels (C/D) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
CARVERDALE CORNER VANITY SINK
Assembly Instructions
3
2R
D

Page |
6
Figure 3
Insert Cam Locks (B) into
corresponding holes on Back Rails
(5/6).
Screw Cam Bolts (A) into threaded
holes on pre-assembled unit from
Figure 2.
Attach Back Rails (5/6) to
pre-assembled unit from Figure 2
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 4
Insert Cam Locks (B) into
corresponding holes on
pre-assembled unit from Figure 3.
Screw Cam Bolts (A) into threaded
holes on Back Post (7).
Attach Back Post (7) to
pre-assembled unit from figure 3
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
5
6
A
A
C
A
7
A

Page |
7
Figure 5
Insert Cam Locks (B) into
corresponding holes on Back Rails
(5/6).
Screw Cam Bolts (A) into threaded
holes on pre-assembled unit from
Figure 4.
Attach Back Rails (5/6) to
pre-assembled unit from Figure 4
by inserting Cam Bolts (A) and
Wood Dowels (C) into
corresponding holes until all panels
meet.
Tighten Cam Bolts (A) by rotating
Cam Locks (B) clockwise using
Phillips screwdriver (not included).
Figure 6
Attach Knob (F) to pre-assembled
unit from Figure 5 with Bolt (G).
Tighten Bolt (G) with Phillips
screwdriver (not included).
Attach pre-assembled unit from
Figure 5 to Bottom Panel (8).
5
6
A
A
A
A
8
F

Page |
8
Figure 7
Connect pre-assembled unit from
Figure 5 to Bottom Panel (8) with
Bolts (J) & Washers (L/M).
Tighten Bolts (J) with Allen Wrench
(N).
Figure 8
Attach Drawer Vertical Panels
(12L/12R) to Drawer Back Panels
(13) with Screws (I) and Wood
Dowels (E).
Tighten Screws (I) with Phillips
screwdriver (not included).
12L
12R
13 E
E
I
I
I
I
J

Page |
9
Figure 9
Attach Drawer Back Panels
(11L/11R) to pre-assembled unit
from Figure 8 with Screws (I) and
Wood Dowels (E).
Figure 10
Insert Drawer Bottom Panel (14)
into grooves of pre-assembled unit
from Figure 9.
11L
11R
14

Page |
10
Figure 11
Attach Drawer Side Panels
(10L/10R) and Drawer Front Panel
(9) to pre-assembled unit from
Figure 10 with Screws (I) and
Wood Dowels (E).
Tighten Screws (I) with Phillips
screwdriver (not included).
Figure 12
Attach Knob (F) to pre-assembled
unit from Figure 11 with Bolt (H).
10L
10R
9

Page |
11
Figure 13
Insert assembled drawer into
assembled unit from Figure 7.
Ensure drawer glides operate
smoothly.
Figure 14
Insert Back Legs (17) into
pre-assembled unit from Figure 14.
If drawer hits adjoining
parts, loosen the
screws on the male
slide and adjust the
height of the drawer.
18
17

Page |
12
Figure 15
Attach Back Legs (17) to
pre-assembled unit from figure 14
with Bolts (K) and Washers (L/M).
Tighten Bolts (K) with Allen Wrench
(N).
Insert Front Legs (16L/16R).
Figure 16
Attach Front Legs (16L/16R) with
Bolts (K) and Washers (L/M).
Tighten Bolts (K) with Allen Wrench
(N).
16L
L
17
17
17
L

Page |
13
Figure 17
Insert pre-assembled unit from
Figure 17 into Top Metal Frame
(15).
15

Page |
14
Figure 18
Attach pre-assembled unit from
Figure17 to Top Metal Frame (15)
with Bolts (K) and Washers (L/M).
Tighten Bolts (K) with Allen Wrench
(N).
Figure19
Attach pre-assembled unit from
Figure 19 to pre-assembled unit
from Figure 13 with Bolts (K) and
Washers (L/M).
Tighten Bolts (K) with Allen Wrench
(N).

Page |
15
Figure 20
Insert Marble Top (1) into
pre-assembled unit from Figure 20.
Figure 21
Now your Carverdale Corner
Vanity Sink is ready for use!
Note: Install not included piping
items: faucet, drain, and supply lines
to vanity sink according to the
instructions supplied with those
items.
Installation of faucet, drain, and
supply lines by a certified plumber is
recommended.
1
If the vanity sink is not level, adjust the foot
pad by hand.

Page |
16
Customer Information
Name
Address
City/State/Zip Code
Phone Number
Please indicate where you purchased this item: Store/Website/Catalog
Please indicate color/size/style number:
Style No Parts Letter Parts Description Quantity Needed
Please immediately examine this product carefully. Any request for missing parts or damage replacement must be
received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time
frame.Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s)
and we are not responsible for any damages due to product modification(s). If damages or missing parts are not
reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise.
For product issues, please contact Southern Enterprises at 800-633-5096 (toll-free) / 972-869-0111 (Dallas),
Mon-Fri 9am – 4pm CST, or email us at [e-mail]. Please ask for customer service representative for
issues involving damages or replacement parts. Please ask for technical assistance representative for any issues
with product and assembly/construction.
Please contact the retailer that you purchased from for returns.
Parts Replacement Form
Customer Service: 1-800-633-5096
[email protected]
Southern Enterprises, Inc.
600 Freeport Parkway, Suite 200
Coppell, Texas 75019