Seiki SB060D User manual

SOUND BAR MODEL: SB060D
PLEASE READ BEFORE OPERATING THIS EQUIPMENT.
Instruction Manual

This symbol indicates that this product incorporates double insulation between hazardous
mains voltage and user accessible parts.
- 1 -
Important Safety Instructions
• Read these Instructions.
• Keep these Instructions.
• Heed all Warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi-
ers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• This symbol indicates that this product incorporates double insulation between hazardous mains voltage and user
accessible parts. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus.When a cart is used, use caution when moving thecart/apparatus combination to avoid injury from tip-over.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the appara-
tus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Special note: When placing your unit on a lacquered or natural finish, protect your furniture with a cloth or other
protective material.
FCC AND IC STATEMENT FOR USERS
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to pro- vide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by SEIKI could void the user’s authority to operate the
equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) this device must accept any interference
received, including interference that may cause undesired operation.
FCC/IC Radiation Exposure Statement
This equipment complies with FCC/IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
Le présent appareil est conforme aux CNR d'industrie Canada applicables aux appareils radio exem pts de licence
L'exploitation est autorisée aux deux conditions suivantes:
(1) I'appareil ne doit pas produire de brouillage; et
(2) I'utillsateur de I'appareil doit accepterbrouillage radioélectrique subi meme si le brouillage est susceptible
d'encompromettre le fonctionnement. mauvais fonctionnement de I'appareil.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain
or moisture. When the mains plug or an appliance coupler is used as the disconnect device,
the disconnect device shall remain readily operable.
CAUTION: These servicing instructions are for use by qualified service personnel only. To
reduce the risk of electric shock, do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.
WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
WARNING: Do not install this equipment in a confined or building-in space such as a book
case or similar unit, and remain a well ventilation conditions at open site. The ventilation
should not be impeded by covering the ventilation openings with items such as newspaper,
table-cloths, curtains etc.
WARNING: Use of this unit near fluorescent lighting may cause interference regarding use
of the remote. If the unit is displaying erratic behavior move away from any fluorescent
lighting, as it may be the cause.
CAUTION: Only use attachments/accessories specified or provided by the manufacturer
(such as the exclusive supply adapter, battery etc).
WARNING: The battery, batteries, and battery pack shall not be exposed to excessive heat
such as sunshine, fire, or the like.
WARNING: Lithium batteries, like all rechargeable batteries are recyclable and should be
recycled or disposed of in normal household waste. Contact your local government for
disposal or recycling practices in your area. They should never be incinerated since they
might explode.
WARNING: Shock hazard - Do Not Open.
Mains Plug or Direct plug-in adapter is used as disconnect device and it should remain
readily operable during intended use. In order to disconnect the apparatus from the mains
completely, the Mains Plug or Direct plug-in adapter should be disconnected from the
mains socket outlet completely.
WARNING: To reduce the risk of fire or electric shock, do not expose
this product to smoke, rain, dust or moisture!
The lightning flash with arrow-head symbol, within an equilateral triangle, is intended to
alert the user to the presence of non-insulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service personnel.
Warnings and Precautions
- 2 -
WARNING: SHOCK HAZARD. DO NOT OPEN
AVIS: RISQUE DE CHOCELECTRIQUE, NEPASOUVRIR

- 3 -
Remove all items from the packing. Retain the packaging. If you dispose of it
please do so according to local regulations.
The following items are included:
for purchasing the excellent quality sound bar for your home.
We recommend that you spend some time reading this instruction manual in order
that you fully understand all the operational features it offers. You will also find some
hints and tips to help you resolve any issues. Read all the safety instructions carefully
before use and keep this instruction manual for future reference.
Thank you
Check the package contents
Sound bar product
3.5mm to 3.5mm
Audio Cable
Adapter
RCA Stereo
Audio Cable
Instruction Manual
Wall-mounted
Bracket
Remote Control
POWER
AUXLINE
MUSIC
TREBLE+ BASS+ VOL+
VOL-BASS-TREBLE-
MOVIE VOICE
PAIR
OPTBT COAX
MUTE

- 4 -
Control buttons
Product description
Power/source
(Long press 3 seconds for standby and
touch for choosing model.)
Volume up
Volume down
Line in socket
Connections
Indicator lights
AUX(L/R) Socket
OPTICAL Socket
COAXIAL Socket
DC IN (20V) Socket
STATE INDICATOR LIGHTS
Off (standby) Red
Line in Green
Aux in Orange
Optical in White
Bluetooth Blue
Coaxial in Emerald green
POWER/
SOURCE
VOL+
VOL-
LINE IN
AUX IN
L
R
OPTICAL IN
COAXIAL IN
20V DC

- 5 -
Remote control (batteries installation)
• The remote control sensor at the front of the soundbar is sensitive to the
remote control’s commands up to a maximum of 6 metres away and within a
maximum arc of 40 degrees.
• Please note that the operating distance may vary depending on the brightness
of the room.
• Remove the battery compartment located on the back of
the remote control.
•The unit comes standard with a battery installed. To avoid
discharging it, it is locked with a plastic tape. Remove the
tape to activate the battery.
• If you have to change, insert a CR2025 3V battery,
observing the correct polarity.
• Replace the battery compartment.
Remote control battery replacement
POWER
AUXLINE
MUSIC
TREBLE+ BASS+ VOL+
VOL-BASS-TREBLE-
MOVIE VOICE
PAIR
OPTBT COAX
MUTE
Long press the pair button to disconnect
bluetooth and search for the equipment again.
PAIR button
Adjust the volume.
VOL +/- buttons
(It must be in mode of MUSIC.)
BASS+/BASS- buttons
Silence the unit or restore the sound.
MUTE button
OPTICAL Input Buttons.
OPTICAL button
COAXIAL Input Buttons.
COAXIAL button
AUX for RCA L/R input.
AUX button
Play/pause/resume playback in Bluetooth
mode.
button
Skip forwards to the next track in Bluetooth
mode.
button
Switch the unit between On and Standby
mode.
button
Line In for 3.5mm input.
LINE button
Bluetooth Input Button.
BT button
Press the button to select a desired music
mode: MUSIC, MOVIE,VOICE.
Music/Movie/Voice buttons
(It must be in mode of MUSIC.)
Treble+/Treble- buttons
Skip backwards to the beginning of the track
or to the previous track in Bluetooth mode.
button

Ensure the TV or Vision Device is placed properly. Turning the volume loud may
cause the device to fall down.
- 6 -
Placing TV or Vision Device
Connections
Use the RCA Stereo Audio Cable to connect the TV’s stereo RCA(L/R) Audio
output socket to the AUX(L/R) Sockets of the unit. Then press the AUX button on
the remote control or press the source button on the unit to choose the AUX
function.
Using the AUX Connection (AUX)
Rear view of the unit
white
red
RCA stereo audio cable
The unit supports a TV up to a dimension of 24 inches to 50 inches and within a
maximum load of 10kg.

Use an optical cable to connect the TV’s optical output socket to the unit’s
OPTICAL socket. Before inserting the optical cable, remove the OPTICAL socket
cover. Then press the OPT button on the remote control or press the source
button on the unit to choose the OPTICAL function.
Using the OPTICAL Connection
Important tips for optical audio:
Use the correct toslink cable and make sure that it is firmly seated in both source
and sound bar sockets.
Optical output is activated on the source (they should see a red light emitting from
the toslink socket).
It may be labeled SPDIF in the setting menu of the source.
The optical output is set to output PCM and not Dolby Digital.
- 7 -
AUX IN
L
R
OPTICAL IN
COAXIAL IN
20V DC
Rear view of the unit
OPTICAL cable
Use a COAXIAL cable to connect the TV’s coaxial output socket to the unit’s
COAXIAL socket. Then press the COAXIAL button on the remote control or press
the source button on the unit to choose the COAXIAL function.
Using the COAXIAL Connection
AUX IN
L
R
OPTICAL IN
COAXIAL IN
20V DC
Rear view of the unit
COAXIAL cable

- 8 -
Use the 3.5mm to 3.5mm audio cable to connect the audio device’s headphone
socket to the unit’s MP3 LINK socket. Then press the LINE button on the remote
control or press the source button on the unit to choose the LINE function.
Using the MP3 LINK Connection (Line In)
POWER/
SOURCE
VOL+
VOL-
LINE IN
Side view of the unit
Audio device
3.5mm to 3.5mm
audio cable
• Ensure all audio connections of the unit are connected before connecting to the
mains power socket.
• Unplug the power cord from the outlet when the unit is use for an extended
period of time.
• Ensure that the power supply voltage is in the voltage of 100V~240V.
• This unit is designed to use adapter.
• Connecting the unit to any other power source may cause damage to the unit.
Unwind the mains cable to its full length. Connect the mains plug to a mains
socket. Make sure the mains plug is fully inserted into the mains socket.
• The mains plug/appliance coupler is used as the disconnect device, the
disconnect device must remain readily operable.
• Connect the Adapter to the unit and AC Socket.
Connecting to the Mains Supply
AUX IN
L
R
OPTICAL IN
COAXIAL IN
20V DC

You can listen to tracks from a media device if it is connected to the unit via
Bluetooth. The Bluetooth’s name is SB060D.
• The operational range between the main unit and a Bluetooth device is
approximately 8 meters.
• Before you connect a Bluetooth device to this unit, familiarize yourself with the
Bluetooth capabilities of the device.
• Keep this unit away from other electronic devices that may cause interference.
If no audio signal is continuously detected from BT, OPTICAL in, AUX in or LINE
in inputs for more than 30 minutes, the unit will power off automatically.
To connect your device to the unit via Bluetooth, follow the steps below:
• Switch the unit on. Press the BT button on the remote control repeatedly to
select BT mode.
• The BT light will flicker and then “BT READY” for searching Bluetooth device.
• Activate your Bluetooth device and select the search mode.
• The product model no. will appear on your Bluetooth delist, select it.
• You will get a warning tone when connection successful.
• To disconnect the Bluetooth function, switch to another function on the unit or
disable the function from your Bluetooth device, or press the pair button on
the remote control.
• The player will also be disconnected when your device is moved beyond the
operational range.
• If you want to reconnect your device to this player, place it within the operational
range.
• If the device is moved beyond the operational range, when it is brought back,
please check if the device is still connected to the player.
• If the connection is lost, follow the instructions above to pair your device to the
player again.
- 9 -
Note: Auto-shut function
Bluetooth Operation

- 10 -
Specifications
(Waste Electrical & Electronic Equipment(WEEE)
Your product is designed and manufactured with high quality
materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at
their end of life should be disposed of separately from your
household waste.
Please dispose of this equipment at your local community waste
collection/recycling centre.
In the European Union there are separate collection systems for
usedelectrical and electronic products.Please help us to conserve
theenvironment we live in!
Pb
Correct disposal of this Product
Power Supply
Standby Power Comsumption
Speaker Output Power
Dimension(W)×(H)×(D)
Net Weight
DC 20V 1.2A
‹0.5watts
30W(Subwoofer)+15W*2
Frequency Respond
SNR
Separation
30Hz-20KHz
70dB
45dB
Bluetooth V3.0+EDR
39”×4”×3” (980×97×67mm)
5.3lbs (2.4kg)