* Before use, open the battery hatch, and insert the batteries included
with your metronome into the battery compartment, referring to
“BATTERY CHANGE” below. (Please note that the dry batteries
included with the metronome are monitor batteries, and their life may
be shorter than the specified period.)
●Metronome function
1. Press the power switch to turn on the metronome.
2. Press the mode switch to set the mode to the metronome.
3. Press the tempo/pitch buttons to set the tempo shown on the
display as desired.
With each press of the respective buttons, the tempo digits
increase or decrease by one as shown below. The digits advance
or move back quickly by keeping the respective buttons pressed.
4. Press the beat/note buttons to set the desired beat (0 ~ 7) or
rhythm.
●Reference note function
1. Press the power switch to turn on the metronome.
2. Press the mode switch to set the mode to the reference note.
3. Press the tempo/pitch buttons to set the pitch shown on the
display as desired.
With each press of the respective buttons, the pitch digits increase
or decrease by one as shown below. The digits advance or move
back quickly by keeping the respective buttons pressed.
4. Press the beat/note buttons to set the desired reference note.
With each press of the respective buttons, the reference note
changes one by one in the following order. It changes quickly by
keeping the respective buttons pressed.
Even after the metronome is turned off, the beat, tempo, reference pitch,
reference note and mode you have set are stored in memory and will
not be initialized.
* If the batteries are replaced, the metronome will return to the following
initial settings.
1. Beat: “0”
2. Tempo: “20”
3. Reference pitch: “440 Hz”
4. Reference note: “A”
5. Mode (metronome/reference note/tap-in): Metronome
●To use DM100 with earphone
Insert the ø3.5 mm earphone plug (SEP-2: sold separately) into the
earphone jack , and press the power switch to turn on the
metronome.
* When the earphone is used, the speaker will not work, and the
sound can be heard only through the earphone.
* The DM100 earphone jack is of a monophonic type. If a stereo-type
earphone is used, the sound can be heard only through one of the
earphones.
MEMORY BACKUP FUNCTION
●Tap-in function
1. Press the power switch to turn on the metronome.
2. Press the mode switch to set the mode to the tap-in.
3. Press the tap-in switch several times constantly at desired
intervals, to a tune, for example.
4. The metronome calculates the input tempo and indicates it on the
display. (The metronome indicates “Lo” when the input tempo is
less than 30, and “Hi” when it is 251 and over.)
5. Press the mode switch to change the mode to the metronome.
The metronome sounds at the tempo you have input in the tap-
in mode. In this case, the metronome plays the beat/rhythm that
has been set previously before the tap-in function is used.
★
A tip on using the tap-in mode
After setting the metronome to the tap-in mode, press the beat/
note buttons to select the desired rhythm, and then, press the
tap-in switch to input tempo. The metronome plays the
selected rhythm at the tempo you have input.
DM100 is equipped with the auto power-off function to prevent the
battery energy from being wasted while the metronome is left untouched
with the power on.
The power will be turned off automatically if the metronome is left
untouched for:
●approximately 20 minutes in the metronome and tap-in modes; and
●approximately 5 minutes in the reference note mode.
To use the metronome for an extended period of time, turn on the power
by pressing the power switch while keeping the mode switch
pressed. Flashing “CLA” appears on the liquid crystal display to
indicate that the auto power-off function is canceled.
AUTO POWER-OFF FUNCTION
Digital Metronome DM100
INSTRUCTION MANUAL
Mode switch
Press it to change over the
mode among metronome, tap-
in and reference note modes.
Tempo/pitch buttons
Press the buttons to set the
tempo in the metronome mode,
and pitch in the reference note
mode.
Earphone jack
Insert the ø3.5 mm earphone
plug into it to use with the
earphone.
Beat/note buttons
Press the buttons to set the
beat/rhythm in the metronome
and tap-in modes, and note in
the reference note mode.
Slit for attaching the
metronome to the music stand
Use the slit to attach the
metronome to the desired
position of the music stand.
Prop-up stand
Power switch
Press it to turn on and off the
metronome.
LED display
It visually represents the tempo
of the metronome with
successive flashing of the LED
lights.
Volume dial
Turn it to adjust the volume of
the tempo/beat sound of the
metronome and the reference
note.
Speaker
It gives out the tempo/beat
sound of the metronome and
reference note.
Strap hole
Use the hole to attach a strap
to the metronome.
Liquid crystal display
It displays the mode, tempo,
reference note and other
settings you have made.
Tap-in switch
Press it several times at
constant intervals. The
metronome calculates and
displays the input tempo.
NAME AND OPERATION OF PARTS
HOW TO USE
