Seiwa SWx 900 Operating and maintenance instructions

MMXRSE0AE012
ÑMMXRSE0AE012zÓ
WARNING AND INSTALLATION MANUAL

1. Warranty and warnings
AvMap Srl warrants every unit to be free from defects in material and workmanship under normal
use and service for a period of 24 months from original retail purchase. During the warranty period,
AvMap Srl will repair or replace any component which fails in normal use without charges for parts
or labour. Technological developments, modications and upgrades of software are not covered by
warranty. To receive warranty service, contact your local authorized dealer for shipping instructions.
The device should be securely packed with its tracking code clearly written on the outside of the
package, shipping to be paid by the customer. Include a copy of the original sales receipt as the
proof of purchase. This limited warranty does not extend to any device which has been subjected to
misuse, neglect, accident, incorrect wiring or improper installation. AvMap Srl reserves the right to
repair or replace the device at its sole discretion.
For more warranty information please see the web site: www.seiwadirect.com
For technical advice or assistance in Europe contact:
AvMap Srl
Viale Zaccagna 6, 54033 Carrara (MS), Italy
Customer support: [phone]
[email protected]
Electronic charts displayed by the device are believed to be accurate and reliable, but they
are not intended to replace o󰀩cial charts which should remain your main reference for all the
matters related to the execution of safe navigation. For this reason we would like to remind
you that you are required to carry on board and use the o󰀩cially published and approved
nautical charts.
Please be aware that the serial ports are not opto-isolated and therefore the peripherals are
electrically connected to the device. This allows the connection of high speed peripherals,
like Fish Finder. If you are connecting a NMEA0183 peripheral and you would like to isolate
it from the device, you have to add the opto-isolator externally.
If water leaks into the equipment, immediately turn o󰀨 the power at the switchboard. Fire or
electrical shock can result.
If the equipment is giving o󰀨 smoke or re, immediately turn o󰀨 the power at the switchboard.
Fire or electrical shock can result.
Do not open the equipment. The equipment uses high voltage that can cause electrical
shock.
Keep the SD card slot’s door closed to avoid water intrusion into the device
Extensive exposure to heat may result in damage to the device.
Please read through the device manual before the rst operation. If you have any questions,
please contact the Company’s customer service or your local dealer.
C-MAP media is available from C-MAP Authorized Resellers.

2
2. Installation
2.1 Bracket Mount
2.2 Panel Mount
2.3 How to insert the MicroSD
1
4 holes
Ø5 mm [0.2”]
20 mm
[0.8”]
20 mm
[0.8”]
4 holes
Ø5 mm [0.2”]
260 mm
[10.2”]
265 mm
[10.4”]
141 mm
[5.5”]
136 mm
[5.3”]

3. Keyboard
The joystick can move the cursor around the map or through menu items. Press [UP], [DOWN],
[LEFT] or [RIGHT].
Each button – except for MOB – can perform two functions: a short press performs the function labeled
on the button; a long press (hold) executes the second function labeled on the unit face (for Power key is
the opposite).
[F1 – F3] long press functions can be customized by the user. This gives you a wider scope of options.
Read the software manual to learn how to customize the functions keys.
[POWER] – [BRIGHTNESS]
Short press: allows to change the brightness.
Long press: turns the device on/o󰀨 when pressed and held in.
[F2] – [WP]
Short press: WP – insert a new waypoint on the cursor position.
[ZOOM IN / ZOOM OUT] – [ENTER]
Rotor: Zoom In/Out if turned on map (it is possible to change default setting to [ROTATE] or [TILT]); if
not on map, move the cursor through menu items like joystick.
Enter: push it to conrm your choice. When on map page, it opens the contextual menu of a map
object.
[F3] – [TRACK]
Short press: Track – start and stop the track.
[MOB]
Is a special button dedicated to man-over-board situation. Pressing MOB places a MOB mark on the
current boat position and starts navigation to that place.
[F1] – [GOTO]
Short press: Go To – to navigate to a destination (desired position on map)
[CLEAR]
Short press: exits from the current menu (back).
Long press: allows to come on the main page or, if you are on map page and the cursor is away from
the boat position, centers the map on the boat position (home mode).
[MARK] – [LIST]
Short press: allows to add a new mark.
Long press: open a mark list.
[MENU] – [PAGE]
Short press: Menu – opens the main menu if pressed on one of the main pages (Map, Fish Finder,
GPS status, Engine monitor). It selects the top bar control buttons if pressed on full menu pages such
as Marks, Routes, Tracks and others.
Long press: Page – shows the main pages, it is the quicker way to switch between pages.
8
1
6
2
3
4
7
5
9
10
1
8
9
10
2
3
4
5
6
7

4. Connections scheme
* SWx 900cw
NMEA 2000 Connector
PIN FUNCTION
1 NOT CONNECT
2 POWER +
3 POWER -
4 SIGNAL H
5 SIGNAL L
GPS Connector (Port C)
PIN FUNCTION
1POWER OUTPUT + (10-35 Vdc)
2 OUTPUT C
3 INPUT C
4 NOT CONNECT
5 NOT CONNECT
6 GND / SIGNAL RETURN
FF Transducer*
PIN FUNCTION
1 XDR POSITIVE
2 XDR SHIELD
3 TEMP
4 +5V
5 ID
6 GND
7 XDR NEGATIVE
8 SPEED
Power & I/O Connector (Port A & Port B)
PIN FUNCTION
1 GND
2 POWER INPUT + (10-35 Vdc)
3INPUT A
4 COMMON
5 OUTPUT B
6OUTPUT A
7 INPUT B
8EXTERNAL ALARM INPUT
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red POWER INPUT + (10-35 Vdc)
4.1 Power supply connection only
3.15A FUSE

Autopilot on Port A
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red POWER INPUT + (10-35 Vdc)
4 Green COMMON
6 Yellow OUTPUT A RX+
COMMON AUTOPILOT
4.2 Autopilot Connections
3.15A FUSE
Autopilot on Port B
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red POWER INPUT + (10-35 Vdc)
4 Green COMMON
5 Gray OUTPUT B RX+
COMMON AUTOPILOT
4.3 External alarm connection
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red PWR + (10-35 Vdc)
8 Blue OUTPUT EXTERNAL ALARM
(Open Collector)
Note: Current MAX 300 mA
3.15A FUSE
3.15A FUSE

●Display size: 9”
●Display resolution: 800x480px
●Display brightness: 1100 nits
●Touch-screen: Capacitive multitouch
●Back-lit keyboard
●Built-in GPS sensor: 10Hz GPS/GLONASS
●Built-in Fish Finder CHIRP*
●External GPS connector
●NMEA 2000
●NMEA 0183: 2x Rx/Tx on power cable
●Transducer connector*
●Memory slot: MicroSD
●WiFi connectivity
●BLE connectivity
●Mounting options: Bracket and flush mount
●Waterproof: IPX6
●Supply voltage: 10-35 Vdc
●Operating temperature: -10°C / +60°C
●Storage temperature: -20°C / +80°C
●Transmitting frequency range: 2400 - 2483 MHz
●Maximum transmitting power: 100 mW
●Maximum power consumption: 12W or 25W*
* SWx 900cw
5. Technical specifications
4.4 NMEA0183 Connections
External NMEA on Port A
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red POWER INPUT + (10-35 Vdc)
3 White INPUT A
4 Green COMMON
6 Yellow OUTPUT A RX+
COMMON
EXTERNAL
NMEA
DEVICE
TX+
External NMEA on Port B
POWER & I/O CABLE
PIN Wire Color Function
1 Black PWR-/GND
2 Red POWER INPUT + (10-35 Vdc)
4 Green COMMON
5 Gray OUTPUT B
7 Brown INPUT B
RX+
EXTERNAL
NMEA
DEVICE
TX+
COMMON
3.15A FUSE
3.15A FUSE
Note: NMEA-0183 input baud rate is automatically detected and selected. If you need to set
the baud rate manually please go into the settings menu.

6. Product conformity information
6.1 FCC compliant
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Changes or modications not expressly approved by the AvMap Satellite Navigation could void the
user’s authority to operate the equipment.
Compliance information statement
Identication of the product
Name P/N
SWx 900w
SWx 900cw
P3MR200WSE
P3CR200WSE
Certied components Wi-Fi and Bluetooth module
FCC ID: Z64-WL18SBMOD
Applicable compliance
statements
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interfer-
ence that may cause undesired operation.
Responsible party
Name AvMap Satellite Navigation Inc
Address
25 Enterprise Zone Drive,
Riverhead, NY 11901
USA
Phone [phone]
Website www.avmap.us
6.2 Simplied EU declaration of conformity
Hereby,
AvMap Srl, Viale Zaccagna 6, 54033 Carrara (MS), Italy declares that the radio equipments in the
following table are in compliance with Directive 2014/53/EU.
SWx 900w P3MR200WSE
SWx 900cw P3CR200WSE
The full text of the EU declaration of conformity for every single product is available at the following
internet address: eudeclaration.avmap.it