Seizmik 08074 Operating and maintenance instructions

1
2 Piece Hood Rack - Installation Manual
Polaris General
Part Number #08074
Seizmik makes Windshields, Doors, Tops, Hood Racks, Mirrors, and other great accessories for utility vehicles &
side x sides. Our products are engineered tough for long life and tested under the harshest of conditions.
Always observe the warnings and precautions in this manual when using your Seizmik products. For best results,
carefully follow the instructions in this manual and make no modifications.
Seizmik products are designed, developed and manufactured by Vialink Corp. If you have any questions,
comments, need assistance, or are missing parts, please call 1-866-838-3366 between 9:00AM and 5:00PM
EST. You can email us at [e-mail]

A
C
E
F
B
D
EG
Parts List
Basket Assembly
2
Parts:
A. 2 Piece Basket
B. Extension tubes (2)
C. Riser tubes (2)
D. Front riser/Light Mounting
Plate
E. Clamp (4)
F. Bumper Mount
G. Roll cage mounts (L,R)
Locking Bolt
Hardware:
(8) M6 x 16mm Button Head Bolts
(1) M6 x 30mm Button Head Bolt
(1) M6 x 35mm Button Head Bolt
(12) M6 Flat Washers
(10) M6 Lock Nuts
(2) M8 X 30mm Hex Head
(4) M8 Flat Washers
(2) M8 Lock Nuts
(2) Metal Spacers
1. Assemble two sides of rack (A). Secure the larger rear tube
with an M6 x 35mm Socket Head bolt and lock nut. Secure the
front smaller tube with an M6 x 30mm Socket Head bolt and
lock nut.
2. Insert an Extension Tube (B) in each end of the hood rack.
Push in just a few inches and tighten the locking bolt in the end
of the tube just enough to hold the extending tube in place. You
will make a final adjustment and tighten later.
M6x35mm
M6x30mm
M6x16mm
M8x30mm M6x20mm

2. Attach the riser assembly to the front of the
hood rack and bolt the (2) front riser caps in
place. Snug the cap bolts, but keep them loose
enough to allow rotation.
3
Hood Rack Pre-Assembly
Locking Bolt
1. Note the riser orientation shown above. Insert the (2) Riser stems (C) into the front riser/light mounting
Plate (D) a few inches in. Tighten the locking bolt at the top of the tube with allen wrench just enough to hold the
riser stems in place. You will tighten after final assembly.
3. Attach the two clamps (E) to the roll cage
clamps (G) with two M6 x 16mm socket head
bolts, 4 washers and 2 nuts. The clamp lever
should open towards the front of the vehicle.
Front of Vehicle
4. Attach the two clamps (E) to the bumper mount (F)
using (4) M6 x 16mm bolts, (2) washers and (4) locknuts.
Make sure all clamp levers open towards the front of the
vehicle.
Front of Vehicle
12
To open a clamp, lift up on both levers in the order
above. Orient all clamps so the first clamp lever
opens towards the front of the vehicle. To increase
clamping force, tighten screw; to decrease the
clamping force, loosen screw before locking.
Adjust screw
for clamping
force
NOTE: Clamp Orientation and adjustment
Front of Vehicle

4
1. Place 2 metal spacers on the tabs on the bumper as
shown above.
Bumper Mount and Vehicle Assembly
Side View
2. Line up the holes on the bumper mount and place
on top of the bumper. Bolt together with M8x30mm hex
head bolts, washers, and M8 locknuts. Make sure the
spacers are between the bumper mount and bumper.
3. Undo the two roll cage bolts holding the A pillers of
the vehicle together, and use these bolts to bolt the roll
cage mounts to the vehicle. The clamps should open
towards the cab of the vehicle.
4. Open all four clamps and place basket assembly on
the on the clamps. Lock all four clamps.
6. Adjust the hood rack angle by loosening the bolt on
the front riser stems and pushing up or down on the
front of the rack. Adjust clamps and brackets as
necessary, then tighten all bolts. We recommend no
more than 5% of slope to the hood rack.
Locking Bolt
5. Adjust the width of the extendable tubes (G) so
they stick out just past the clamps. (If necessary)