SELF SLPU-2P2U1S-WL-BK User manual

SLPU-2P2U1S-WL-BK
ELECTRICAL
CERTIFICATION
FCC compliant and UL Listed
WARRANTY
5 Years
MECHANICAL
Recessed mounting
Installation
Dimmension(inches/mm)
Cut hole size:
7.40"×2.09"(188mm×53mm)
With 2 × USB-A charger ports (Rated 5Vdc, 3.1A)
USB charger built-in open circuit, short circuit, over load protection
2 × TR AC Receptacles, rated 15A，125Vac
Wireless 3-way switching, controls the rear receptacle
for LED light fixtures
10' 14 AWG x 3C power cord with 5-15P plug
8" rear/side exiting cord with receptacle
7-12/16”(197) 2-1/8”(54)
2-1/2”(63)
*Thickness of the board:8~35mm
SELF Electronics USA Corporation
Tel: [phone] Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT

3-way Switching Function
Pairing
Unpair for 3-way version power units
1Power on Press power unit’s start button more than 3 seconds, the blue
indicator beside button starts flashing, Power unit enters paring mode.
Repeat same operation to another power unit.
Short press the button of any power unit, the blue indicator will
stop flashing and stay ON or OFF, means the pairing is successful.
press any paired power unit’s switch, all the lights that powered by paired
power units can be contolled.
2
1Power on Press power unit’s start button more than 6 seconds,
until the blue indicator button starts flashing then stays ON,
means the unpairing is successful.
2
3 4
SELF Electronics USA Corporation
Tel: [phone] Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT
flashing
flashing
3s
3s
a
b
stop flashing stop flashing
or
or
flashing
6s

SLPU-2P2U1S-WL-WH
ELECTRICAL
CERTIFICATION
FCC compliant and UL Listed
WARRANTY
5 Years
MECHANICAL
Recessed mounting
Installation
Dimmension(inches/mm)
Cut hole size:
7.40"×2.09"(188mm×53mm)
With 2 × USB-A charger ports (Rated 5Vdc, 3.1A)
USB charger built-in open circuit, short circuit, over load protection
2 × TR AC Receptacles, rated 15A，125Vac
Wireless 3-way switching, controls the rear receptacle
for LED light fixtures
10' 14 AWG x 3C power cord with 5-15P plug
8" rear/side exiting cord with receptacle
7-12/16”(197) 2-1/8”(54)
2-1/2”(63)
*Thickness of the board:8~35mm
SELF Electronics USA Corporation
Tel: [phone] Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT

3-way Switching Function
Pairing
Unpair for 3-way version power units
1Power on Press power unit’s start button more than 3 seconds, the blue
indicator beside button starts flashing, Power unit enters paring mode.
Repeat same operation to another power unit.
Short press the button of any power unit, the blue indicator will
stop flashing and stay ON or OFF, means the pairing is successful.
press any paired power unit’s switch, all the lights that powered by paired
power units can be contolled.
2
1Power on Press power unit’s start button more than 6 seconds,
until the blue indicator button starts flashing then stays ON,
means the unpairing is successful.
2
3 4
SELF Electronics USA Corporation
Tel: [phone]
3264 Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT
flashing
flashing
3s
3s
a
b
stop flashing stop flashing
or
or
flashing
6s

SLPU-2P2U1S-WL-NI
ELECTRICAL
CERTIFICATION
FCC compliant and UL Listed
WARRANTY
5 Years
MECHANICAL
Recessed mounting
Installation
Dimmension(inches/mm)
Cut hole size:
7.40"×2.09"(188mm×53mm)
With 2 × USB-A charger ports (Rated 5Vdc, 3.1A)
USB charger built-in open circuit, short circuit, over load protection
2 × TR AC Receptacles, rated 15A，125Vac
Wireless 3-way switching, controls the rear receptacle
for LED light fixtures
10' 14 AWG x 3C power cord with 5-15P plug
8" rear/side exiting cord with receptacle
7-12/16”(197) 2-1/8”(54)
2-1/2”(63)
*Thickness of the board:8~35mm
SELF Electronics USA Corporation
Tel: [phone]
3264 Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT

3-way Switching Function
Pairing
Unpair for 3-way version power units
1Power on Press power unit’s start button more than 3 seconds, the blue
indicator beside button starts flashing, Power unit enters paring mode.
Repeat same operation to another power unit.
Short press the button of any power unit, the blue indicator will
stop flashing and stay ON or OFF, means the pairing is successful.
press any paired power unit’s switch, all the lights that powered by paired
power units can be contolled.
2
1Power on Press power unit’s start button more than 6 seconds,
until the blue indicator button starts flashing then stays ON,
means the unpairing is successful.
2
3 4
SELF Electronics USA Corporation
Tel: [phone]
3264 Saturn Ct,Peachtree Corners,GA 30092 [email protected]
POWER UNIT
flashing
flashing
3s
3s
a
b
stop flashing stop flashing
or
or
flashing
6s