Sena NP200G User manual
NP200G-Cellular
User’s Manual
Rev. 2.0
Date: 18th June 2020
This manual belongs to: _______________________________________
Company: __________________________________________________
NP200G-Cellular
2
Proprietary Notice
This document and its contents are proprietary to Sena World, Inc. and shall not be
reproduced, copied or used in whole or in part without the written consent of an officer of Sena
World, Inc., a Texas corporation.
This document is for information purposes only and is subject to change without notice.
Sena World, Inc. thanks you for purchasing this product and hopes that it can fulfil all your
CNG controller needs now and in the future.
NP200G-Cellular
3
Revision History
Version Page Date Reason
--------- ----- ------- ------------------------------------------------------------------------
-------------
1.0 03/07/19 Initial release
2.0 18/06/20 Update
Please Note:
Sena World, Inc. encourages and appreciates customer
feedback regarding this document errors or improvements. If you
have any questions regarding this manual or this product, please call
or write to the following:
Please respond to:
Sena World, Inc.
10606 Shady Trail, suite 106
Dallas, TX 75220
Factory Tel: (972) 488-8724
Internet Home page: www.Sena World.com
E-mail: patelnp@sena-corp.com
NP200G-Cellular
4
Table of Content
Contents
Table of Contents
Introduction.............................................................................................................................................. 5
Shipping Carton....................................................................................................................................... 6
Install NP200G-Cellular unit ............................................................................................................... 7
Setup NP200 G-Cellular unit................................................................................................................ 8
NP200 Operations.................................................................................................................................10
LCON Operations...................................................................................................................................11
Notes: ........................................................................................................................................................22
NP200G-Cellular
5
Introduction
SENA’s NP200G provides the same “near real time” tank monitoring information
through SENA’s LCON website as our NP200G but does so by using cellular networks. Ideal for
locations/operations that do not have internet access the NP200G supports global 2G,3G/4G and
LTE networks and works with various cellular partners. Values are periodically transferred
(frequency is user-defined) utilizing cellular data to the LCON site for customer web-based
applications. The LCON website is a secure web portal which gives customers multilevel global
access to the NP-200 series tank monitors via the internet. All NP200 series of products can be
used as a stand-alone monitoring and control system with built-in MODBUS protocol. Ideal for
SCADA systems interface.
NP200 inputs/outputs
•4 Analog Input
•4 Digital Input
•4 Digital Output
•RS485 channel
NP200G-Cellular
6
Figure 1
Shipping Carton
1) NP200G-Cellular
2) 8AA Battery
3) Manual
4) Warranty card
5) Mounting Screws
Battery
Mail to:
SENA Corporation
10606 Shady Trail
Suite 106
Dallas, TX 75220
Attn: Merchandize Warranty
NP200W-LPG
Back Side
Front Side
Warranty Card
Model: NP200W-LPG
SN#: 03072019
Date:
Sold To:
Address:
GPS Antenna
GSM Antenna
NP200G-Cellular
7
Figure 2
Install NP200G-Cellular unit
1. Survey site the NP200 is to be installed
2. Mark spot where unit is to be installed i.e. position of the 4 mounting holes
3. Using the appropriate screws, install the unit on the wall so that it is vertical
4. This mark should be about 2’ or 600 mm from wall where unit is installed
5. Remove the caps for attach GSM and GPS antenna. Attach the appropriate antenna’s to
connector as shown in figure 2.
GPS Antenna
GSM Antenna
NP200G-Cellular
8
Figure 3
Setup NP200 Unit
●Open the lid of Unit and plug the batteries as shown in the figure 3.
●To wake up system, customer needs to hold magnet in front of Red dot on the unit for 3
sec as shown in figure 4.
●Unit indicator LED will flash every one second and send the report to the server.
NP200G-Cellular
9
Figure 4
NP200G-Cellular
10
NP200 Operations
•To wake up system, customer needs to hold magnet in front of Red dot on the unit for 3
sec as shown in figure 4.
•When unit starts, it will blink green LED and take all readings and when it tries to
register SIM on network, it will blink red LED. Once it is successfully registered and
connected to the server, it will start flashing green led and will send report to server.
•It will send report two times a day i.e. 5 am and 3 pm as per default setting.
•When server communicates with RS485 sensor it will blink Green, Orange, Red till the
communication with sensor is over.
•After sending report, it will start flashing Green, Orange, Red LED for 2-3 sec and will
go back to sleep.
•If customer needs to change the report time then he can change it from “sena-corp.com”
website.
NP200G-Cellular
11
LCON Operations
1) Access your internet and go to sena-corp.com
2) In the upper right corner click on “Login”
3) Login into LCON with your credentials. (If you don’t have login credentials please contact
Sena Email:patelnp@sena-corp.com)
4) Click on “Submit” figure 5
5) LCON page will now display
6) Dashboard Page will now display. figure 6
Figure 5
NP200G-Cellular
12
Figure 6
NP200G-Cellular
13
7) Identify the Unit and click on text in Description tab
8) Now Tank Information Page will open. (figure 7)
9) For check Report history click on hyper link “Unit History”. You will navigate to Unit
History Page. Figure 8.
Figure 7
NP200G-Cellular
14
10)For Report Notification (Email alerts) click on hyper link “Unit Notification”. You will
navigate to Unit notification Page. Figure 9. (only Admin will have the access of this page)
•For getting alerts on high and low readings. Please Fill the values in the fields (High-
High, High, Low- Low, Low) that you think that reading will be alert reading. After That
check the check mark. You can select the type of alerts like Hi-Hi, Hi, Lo-Lo, Lo, unit
report, etc..
Figure 8
NP200G-Cellular
15
11)For changing Unit setting Remotely click on hyper link “Unit Remote Commands”. You will
navigate to Unit Remote Commands Page. Figure 10. ( only Admin will have the access of
this page)
You Can change the below fields remotely.
•UTC Date and UTC Time: Date should be in format YYMMDD and time should be in
format HHMMSS
•Offset: You can change the offset values. For example, you want to set the offset -24 so
you should have the enter 24 and if you want set +24 value should 124.
•Individual Register Scanning: For Scanning Only one type of registers you can press
the buttons ScanAI, ScanDI, ScanDO, ScanRH
•Reports Alarms: Here is you have 12 options to set report time alarms. You have to set
alarms in format HHMM. Also, if you want hourly report enter 9900 in one filed you will
get hourly reports.
•Change Output’s: You can change the output values by pressing available buttons.
Means if current value is ON then you can press OFF button. If current values are OFF,
then you press ON button.
Figure 9
NP200G-Cellular
16
•ADC Alarms: You set the High and Low alarm values. This value should be in integer
format. You can set values for 8 channels. You can also delete the high and low alarm
pressing Delete buttons.
•Row Units: You can set the Low and high row units (HRU, LRU) for 4 channels. This
value should be in integer format.
•Engineering Units: You can set the Low and high Engineering units (HEU, LEU) for 4
channels. This value should be in floating format.
Figure 10
NP200G-Cellular
17
12)You can change the unit setting for calculation using Unit modification Page. This
calculation is only for Lcon side. Visit this page by select hyper link “Unit Modification”.
Figure 11.
Figure 11
NP200G-Cellular
18
13)For check Battery history click on hyper link “Battery History”. You will navigate to battery
History Page. Figure 12.
14)For Battery Report Notification (Email alerts) click on hyper link “Battery Notification”.
You will navigate to battery notification Page. Figure 13. (only Admin will have the access
of this page).
•For getting alerts on high and low battery readings. Please Fill the values in the fields
(High- High, High, Low- Low, Low) that you think that reading will be alert reading.
After That check the check mark. You can select the type of alerts like High-High, High,
Low-Low, Low, unit report, etc..
Figure 12
NP200G-Cellular
19
Figure 13
NP200G-Cellular
20
15) For seeing register values select “Unit page” hyper link. Figure 14
Figure 14
Table of contents
Popular Measuring Instrument manuals by other brands
Bierer
Bierer DCI-100-CT operating instructions
Badger Meter
Badger Meter Primo Advanced BMAG-350-icpf Instruction and operation manual
SPM
SPM Vibrameter VIB-11B instruction manual
Keysight Technologies
Keysight Technologies S9106AC-2IF Startup guide
Masimo
Masimo PRONTO-7 Operator's manual
WIKA
WIKA A2G-05 operating instructions
