Sencor SPT 232 User manual

INSTRUCTION MANUAL
NÁVOD K OBSLUZE
NÁVOD NA OBSLUHU
FELHASZNÁLÓI KÉZIKÖNYV
INSTRUKCJA OBSŁUGI
РУКОВОДСТВО ПО
ЭКСПЛУАТАЦИИ
NAUDOTOJO VADOVAS
Portable Radio with CD/MP3/USB Player
Přenosný radiopřijímačs CD/MP3/USB přehrávačem
Prenosný rádioprijímačs CD/MP3/USB prehrávačom
Hordozható rádió CD/MP3/USB lejátszóval
Przenośny radioodbiornik z odtwarzaczem
CD/MP3/USB
Портативный радиоприемник
сCD/MP3/USB-плеером
Nešiojamasis radijas su CD/MP3/USB grotuvu
SPT 232
RU LT

EN - 3
WARNING
TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : SHOCK HAZARD-DO NOT OPEN
LIGHTNING FLASH WITH ARROWHEAD
SYMBOL - within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated dangerous voltage within the
products enclosure that may be of sufficient
magnitude to constitude a risk of electric shock
to persons.
EXCLAMATION POINT - within an equilateral
triangle, is used to indicate that a specific
component shall be replaced only by the
component specified in that documentation for
safety reason.
The following label has been affixed to the unit, listing the proper procedure for working with
the laser beam:
CLASS 1 LASER PRODUCT
KLASS 1 LASER APPARAT
LUOKEN 1 LAISERLAITE
KLASSE 1 LASER PRODUKT
CLASS 1 LASER PRODUCT LABEL -
This label is attached to the place as illustrated to inform
that the apparatus contains a laser component.
WARNING LABEL INFORMING OF RADIATION -
This label is placed inside the unit. As shown in the
illustration. To warn against further measures on the
unit. The equipment contains a laser radiating laser rays
according to the limit of laser product of class 1.

EN - 4
SAFETY INSTRUCTIONS
1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the
appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instruction should be retained for future
reference.
3. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS - All operating instructions should be followed.
5. WATER AND MOISTURE - The appliance should not be used near water, for example, near
a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
6. VENTILATION - The appliance should be situated so that its location or position does not
interfere with its proper ventilation. Do not place on bed, sofa, rug or similar surface that may
block the ventilation openings, in a built-in installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
7. HEAT - The appliance should be situated away from heat sources such as radiators, stoves, or
other appliances (including amplifiers) that produce heat.
8. POWER SOURCE - The appliance should be connected to power supply only of the type
described in the operating instructions or as marked on the appliance.
9. POWER CORD PROTECTION - Power supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against them.
10. POWER LINES - An outdoor antenna should be located away from power lines.
11. OBJECT and LIQUID ENTRY - Care should be taken so that objects do not fall and liquids are
not spilled into the enclosure through openings.
12. ESD WARNING - The display does not function properly or no reaction to operation of any the
control may due to the electrostatic discharge. Switch off and unplug the set. Reconnect after
a few seconds.
13. DAMAGE REQUIRING SERVICE - The appliance should be serviced by qualified service
personnel when:
a. The power-supply cord or plug has been damaged.
b. Objects have fallen into, or liquid has been spilled into the appliance enclosure.
c. The appliance has been exposed to rain.
d. The appliance has been dropped, or the enclosure damaged.
e. The appliance does not appear to operate normally.
14. SERVICING - The user should not attempt to service the appliance beyond that described in the
user operating instructions. All other servicing should be referred to qualified service personnel.

EN - 5
SAFETY INSTRUCTIONS
Notes:
a. Dirty or scratched CD may cause a skipping problem. Clean or replace the CD.
b. If an error display or malfunction occurs, disconnect the AC cord and remove all the batteries.
Then turn the power back on.
BEFORE OPERATION
Notes: CONCERNING COMPACT DISCS.
Since dirty, damaged or warped discs may damage the appliance, care should be taken of the
followings items:
a. Usable compact discs. Use only compact disc with the mark shown below.
b. CD compact disc only with digital audio signals.

EN - 6
POWER SOURCES
to a wall outlet to AC IN Insert 6 × “C” size batteries
into the battery compartment
AC POWER
You can power your portable system by plugging the detachable AC power cord into the AC inlet at
the back of the unit and into a wall AC power outlet. Check that the rated voltage of your appliance
matches your local voltage. Make sure that the AC power cord is fully inserted into the appliance.
BATTERY POWER
Insert 6 × “C” size batteries into the battery compartment. Be sure that the batteries are inserted
correctly to avoid damage to the appliance. Always remove the batteries when appliance will not be
used for a long period of time, as this will cause leakage to the batteries and subsequently damage
to your set.
Notes:
- Use batteries of the same type. Never use different types of batteries together.
- To use the appliance with batteries, disconnect the AC power cord from it.

EN - 7
LOCATION OF CONTROL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1 FM ANTENNA
2 HANDLE
3 LCD DISPLAY
4 STANDBY / FUNC
5 VOL +
6 VOL -
7 STOP
8 SKIP- / TUN -
9 USB JACK
10 CD DOOR
11 OPEN / CLOSE
12 MODE / AMS
13 PRE + / FOLDER +
14
PRE - / FOLDER -
15 PLAY / PAUSE / CLOCK
16 SKIP+ / TUN+
17
18
19
17 AC CORD
18 AUX-IN JACK
19 HEADPHONE JACK

EN - 8
RADIO OPERATION
AUTOMATIC TUNING
1. Press the “STANDBY / FUNC.” button to select “RADIO” mode.
2. Press and hold the “SKIP + / Tun +” or “SKIP - / Tun -” button over 3 seconds to start automatic
tuning process.
3. When a station is tuned in the tuning process, it will stop automatically and you can listen to your
desired station.
AUTOMATIC MEMORY STATIONS (AMS)
1. Press and hold the „MODE / AMS“ button on unit for about 2-3 seconds to start the automatic
preset process.
2. Display will show the memory sequence number and radio stations will be automatically preset
into the sequence number (Note: Each sequence number means 1 preset station while during
automatic preset process.)
3. Once all the stations were automatic preset, press the “Pre +” or “Pre -“ button to choose preset
stations.
MANUAL TUNING
It is for selecting stations, which cannot be tuned automatically. (manual selection)
To tune a channel manually.
- Skip step 4 in the above “AUTOMATIC TUNING” procedures.
- In step 3, each time the “SKIP + / Tun +” or “SKIP - / Tun -” button is pressed momentarily
(0.5 second or less), the frequency changes by a fixed step:
FM: 0.1 MHz steps
MANUAL MEMORY PRESET
1. Choose the desired station by following „AUTOMATIC TUNING“ or “MANUAL TUNING” step 1 to
3 procedure.
2. Press „MODE / AMS“ button to enter manual preset station setting.
3. Display will show “P01” flashing.
4. Press “SKIP + / Tun +” or “SKIP - / Tun -” button to choose preset station number.
5. Press „MODE / AMS“ button to confirm chosen preset station number.
6. Once all the stations were preset, press the “PRE - / FOLDER -” or “PRE + / FOLDER +“ button to
choose your desired station.
Radio contens 20 preset stations.
FOR BETTER RECEPTION
- Reorient the antenna for better reception

EN - 9
CD / MP3 OPERATION
GENERAL OPERATION
PLAY / PAUSE Press to start playing CD / MP3 disc.
Press again to stop playing CD / MP3 operation
temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the
sound.
STOP Press to stop all CD / MP3 operation.
PLAYBACK
1. Set the “STANDBY / FUNC.” selector to “CD” mode.
2. Open the CD door and place a CD / MP3 disc with the label up in the CD compartment.
3. Close the CD door.
4. Focus search is performed if disc is inside.
For CD disc - Total number of tracks is read and appears on the display.
For MP3 disc - “MP3” appears on the display.
5. Press the “PLAY / PAUSE” button to start playing CD / MP3 disc.
6. Press the “VOL +” or “VOL -“ to adjust the VOLUME control to the desired level.
7. Press the “PLAY / PAUSE” button again when you want to stop playback temporarily.
8. Press the „STOP“ button when finished.
ALBUM
When unit is under operation in MP3 press “PRE - / FOLDER -” or “PRE + / FOLDER + “ button to
choose ALBUM folder.

EN - 10
USB OPERATION
GENERAL OPERATION
PLAY / PAUSE Press to start playing tracks from the USB.
Press again to stop playing USB operation temporarily.
Press again to resume playback.
SKIP + & Press to go to the next track or back to the previous track.
SKIP - Press and hold while playing until you find the point of the
sound.
STOP Press to stop all USB operation.
PLAYBACK
1. Plug or slot in USB device to the port.
2. Press the “STANDBY / FUNC.” button to select “USB” mode.
3. The LCD will display “READING” while the stereo scans for MP3 from the USB device.
The LCD will display the total number of the folders of MP3 files and start the playback
automatically.
4. Press the “PLAY / PAUSE” button again, when you want to stop playback temporarily.
5. Press the “STOP” button when finished.
STOP Press to stop all USB operation.
6. Press the „STOP“ button again to stop all USB operation.
REPEAT
Press the “MODE” button during playing USB,
1 - REPEAT 1 (FLASHING)
2 - REPEAT FOLDER ( *MP3 ONLY “ALBUM” )
3 - REPEAT ALL
4 - RANDOM
5 - NORMAL PLAYBACK
REPEAT 1 REPEAT
ALBUM REPEAT ALL
NORMAL
PLAYBACK RANDOM

EN - 11
OTHER OPERATION
AUX IN
Press the “STANDBY / FUNC.” button to select “AUX” mode to listen to the external audio devices
connected through the 3.5mm Auxiliary Stereo Line-In jack. Press FUNTION to select “LINE” mode.
In “LINE” mode, the display will show back to the normal time and calendar display.
1. Use a 3.5mm Male-to-Male Stereo cable to connect any external audio device with a 3.5mm
Headphone or Line-Out jack to the AUX IN jack on the rear panel of the stereo.
2. Start playback on the external audio device. Adjust the volume on the audio device (do not set the
volume too high to avoid distortion). You may also adjust the volume on the appliance.
3. To control playback function, use the controls provided by the external audio device.
CLOCK SETTING
1. Press the “STANDBY / FUNC.” button for 3-4 seconds to switch unit at standby mode.
2. Press and hold the “PLAY / PAUSE / CLOCK” button for 3-4 seconds to entry clock set mode.
3. Adjust time format by pressing the “SKIP + / Tun +” or “SKIP - / Tun -” button.
4. Press the “PLAY / PAUSE / CLOCK” button to confirm time format
Notes:
- Because clock setting is at standby mode, the display is dim.
- Clock set will always be “24hr” time format.
- While unit is under operation, press and hold the “PLAY / PAUSE / CLOCK” button for 3-4
seconds to see the time.
STANDBY MODE
- Press the “STANDBY / FUNC.” button for 0.1 second to switch unit to operation.
- Press the “STANDBY / FUNC.” button for 3-4 seconds during operation to switch unit to standby.

EN - 12
Technical Parameters
FM radio frequency range 87.5 – 108 MHz
USB connector: max. 32 GB
Output power: 2 x 1,5 W RMS
Power supply: AC 230 V, 50 Hz or batteries 6 x 1,5V type C
Power consumption: 9 W
Dimensions: 256 x 225 x 128 mm
Weight: 1.28 kg

EN - 13
EN Warranty conditions
Warranty card is not a part of the device packaging.
This product is warranted for the period of 24 months from the date of purchase to the end-user. Warranty is limited to
the following conditions. Warranty is referred only to the customer goods using for common domestic use. The claim
for service can be applied either at dealer’s shop where the product was bought, or at below mentioned authorized
service shops. The end-user is obligated to set up a claim immediately when the defects appeared but only till the end
of warranty period. The end user is obligated to cooperate to certify the claiming defects. Only completed and clean
(according to hygienic standards) product will be accepted. In case of eligible warranty claim the warranty period will
be prolonged by the period from the date of claim application till the date of taking over the product by end-user, or
the date the end-user is obligated to take it over. To obtain the service under this warranty, end-user is obligated to
certify his claim with duly completed following documents: receipt, certificate of warranty, certificate of installation.
This warranty is void especially if apply as follows:
Defects which were put on sale.
Wear-out or damage caused by common use.
The product was damaged by unprofessional or wrong installation, used in contrary to the applicable instruction
manual, used in contrary to legal enactment and common process of use or used for another purpose which has
been designed for.
The product was damaged by uncared-for or insufficient maintenance.
The product was damaged by dirt, accident of force majeure (natural disaster, fire, and flood).
Defects on functionality caused by low duality of signal, electromagnetic field interference etc.
The product was mechanically damaged (e.g. broken button, fall).
Damage caused by use of unsuitable media, fillings, expendable supplies (batteries) or by unsuitable working
conditions (e.g. high temperatures, high humidity, quakes).
Repair, modification or other failure action to the product by unauthorized person.
End-user did not prove enough his right to claim (time and place of purchase).
Data on presented documents differs from data on products.
Cases when the claiming product cannot be indentified according to the presented documents (e.g. the serial
number or the warranty seal has been damaged).
Authorized service centers
Visit www.sencor.eu for detailed information about authorized service centers.

EN - 14
2014 10/2014
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING
MATERIALS
Take the packaging material to a designated municipal waste facility.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that used electric or electronic
products must not be added to ordinary municipal waste. For proper disposal and
recycling, take these products to designated collection points. Alternatively, in some
European Union states or other European countries you may return your appliances to
the local retailer when buying an equivalent new appliance. Through the correct disposal
of this product you will help retain valuable natural resources and prevent potential
negative effects on the environment, which could result from its incorrect disposal of
waste. Ask your local authorities or collection facility for more details. In accordance with
national regulations penalties may be imposed for the incorrect disposal of this type of
waste.
For business entities in European Union states
If you want to dispose of electric or electronic devices, ask your retailer or supplier for the
necessary information.
Disposal in other countries outside the European Union
This symbol is valid in the European Union. If you wish to discard this product, ask your
local authorities or retailer about proper disposal.
This product meets all the basic requirements of EU directives that apply to it.
Changes to the text, design and technical specifications may occur without prior notice and we reserve
the right to make these changes.