Sencore OmniHub CMP100 User manual

Quick Start Guide Sencore OmniHub CMP100
Version 1.0 - December 2019 Page 1
About This Quick Start Guide
This guide is for helping new customers get their Sencore OmniHub CMP100 setup
and running as quickl and easil as possible.
The CMP100 allows users to Encode Signal via CVBS, SDI and HDMI; Receive
Signal from DVBC, DVBS/S2, DVBT and 8VSB; Modulate to QAMA/B, 8VSB, OFDM,
and ISDBT; and some other Function like EAS and CAM.
Download the Full User’s Manual
The current versions of the full user’s manuals can be obtained from the Download
tab of the CMP100 product page on our website: www.sencore.com or b emailing
Sencore ProCare support at [e-mail].
Unpack the Equipment
Check that there are no signs of damage to equipment due to transport. If the
equipment appears to be damaged, please contact Sencore ProCare for support.
In addition to the Sencore CMP100 Chassis hardware itself, the box should include
two power cables, and adapter cables depending on the Option Modules included.
Equipment nstallation and Power Up
The CMP100 is designed for rack installation and should be securel connected to the
rack using screws suitable for the rack t pe. Note that there should be sufficient room
for air to freel flow around the unit, ensuring proper cooling. The CMP100 requires
front-to-back airflow.
When the equipment is installed, it should be powered b connecting both power
cables to power outlets. If one of the redundant power supplies is disconnected from
power, the unit will still work. Re-establish power to the second power suppl is
recommended for the smooth performance of the unit. The CMP100 can operate in
the range 90–240VAC.
Figure 1: IP Port Connectors
Establish Web Connection to the CMP100
In order to access the CMP100 web user interface, it is necessar to establish an
Ethernet connection to the device.
Using the Pre-Set Management P Address
The Sencore CMP100 is shipped with the following factor settings for management
port 1 and 2(the same IP address is assigned to both ports):
Management Port 1 and 2 IP address: 192.168.1.10
Management Port 1 and 2 subnet mask: 255.255.255.0
In order to connect to management port 1 or 2, the PC used for setup should have
corresponding network settings. Connect a PC directl to the device’s management
port using an Ethernet cable.
For Windows, the network parameters are set in the Control Panel — Network and
nternet — Network and Sharing Center — Network Connection — Properties —
nternet Protocol Version 4 Properties view, as shown in figure 2. Select the user
defined address and set the PC’s IP address to 192.168.1.xx (xx is not 10 to 26) and
the subnet mask to 255.255.255.0.
When the IP address of the PC has been set in the same subnet as the CMP100’s
factor setting, a web browser can be used to access the web user interface at
192.168.1.10.

Quick Start Guide Sencore OmniHub CMP100
Version 1.0 - December 2019 Page 2
Figure 2: Setting the IP address manuall in Windows
Connect to the Web User nterface of the CMP100
Launch a web browser application on the management PC. The following web
browsers are supported:
• Microsoft Internet Explorer 11 or higher
• Mozilla Firefox 29 or higher
• Google Chrome
T pe the management IP address of the CMP100 in the browser URL field and press
ENTER. The web UI will be displa ed.
Figure 3: CMP100 Login Web UI
Check nserted Modules in the CMP100
To Login on the CMP100 management GUI. User and Password is admin/admin.
Inserted Modules should show on the module list on the left side of the GUI to be able
to configure and use them. The status will be shown on the main page showing the
Chassis front panel as show in the image below.
In order to setup for Encoding, Receiving and Modulating the Option Modules
connected in CMP100 chassis, please refer to the CMP100 user manual for more
details on how to do this.
Figure 4: CMP100 Status page
Support
Contact Sencore ProCare for support, if required.
Email: [e-mail]
Phone: [phone]