Sensata ISOSLICE-2 User manual

Sensata Technologies 1 220808
ISOSLICE-2 User Manual
ISOSLICE-2
8 Analog Input Isoslice Unit
Whilst every effort has been taken to ensure the accuracy of this document, we
accept no responsibility for damage, injury, loss, or expense resulting from errors or
omissions, and reserve the right of amendment without notice.
This document may not be reproduced in any way without the prior written
permission of the company
AUG 2022

Sensata Technologies 2 220808
The ISOSLICE-2 unit has 8 analog inputs. It can be configured to accept a variety of high-
level unipolar (positive) signals. This is achieved using the 8-way dipswitches shown in the
picture below:
Default input types and ranges
Default input ranges can be selected using the dipswitches S1, S2, and S3 from the table
below. Before settings are changed, the inputs must be disconnected, and the ISOSLICE-
2 must be powered off.
Switches Used
Switch Settings
S1 (Type)
S2 (Type)
S3 (Range)
4 - 20mA (Current)
0 - 10V (Voltage)
Input 1
1,2
-
1
S1:1,2 on S3:1 off
S1:1,2 off S3:1 on
Input 2
3,4
-
2
S1:3,4 on S3:2 off
S1:3,4 off S3:2 on
Input 3
5,6
-
3
S1:5,6 on S3:3 off
S1:5,6 off S3:3 on
Input 4
7,8
-
4
S1:7,8 on S3:4 off
S1:7,8 off S3:4 on
Input 5
-
1,2
5
S2:1,2 on S3:5 off
S2:1,2 off S3:5 on
Input 6
-
3,4
6
S2:3,4 on S3:6 off
S2:3,4 off S3:6 on
Input 7
-
5,6
7
S2:5,6 on S3:7 off
S2:5,6 off S3:7 on
Input 8
-
7,8
8
S2:7,8 on S3:8 off
S2:7,8 off S3:8 on
User calibrated input types and ranges
The inputs can also be user calibrated for wider input ranges. Choose the settings from the
table for either current or voltage.
Current: 0 - 1 mA up to 0 - 20 mA (e.g., Input 1: 0 - 1 mA S1:1,2 on S3:1 off)
Voltage: 0 - 1 V up to 0 - 40 V (e.g., input 4: 0 - 5 V S1:7,8 off S3:4 on)
The range shown above is the maximum the switch settings will allow. The ADC can adjust
the gain to use full resolution for ranges that are less than those shown.
The calibration sequence is described in the last section of the manual.
Restoring default values
Default values are restored by changing the corresponding dipswitch on S3 for the input
and power cycling, then changing it back again.
To restore default values (e.g., 4-20mA on input 1).
Power off the ISOSLICE-2. Change S3:1 to ON. Power on the ISOSLICE-2. It will load in
default values for 0 - 10V.
Power off the ISOSLICE-2. Change S3:1 to OFF. Power on the ISOSLICE-2. It will load in
S1 selects the input type for inputs 1,2,3,4
S2 selects the input type for inputs 5,6,7,8
S3 selects the default input ranges
S4 selects the ISOSLICE bus channel (2 to
128)

Sensata Technologies 3 220808
default values for 4 - 20mA.
Channel number
The channel number is selected using S4. The channel number must be between 2 and
128, using switches 2 to 8. If all switches are off, the channel number is 1 (invalid):
The channel number is a binary reading of switches 2 to 8, with switch 8 the lowest bit.
S4 1 = On, 0 = Off
Channel 2 3 4 5 6 7 8 Channel 2 3 4 5 6 7 8
1 0 0 0 0 0 0 0 9 0 0 0 1 0 0 0
2 0 0 0 0 0 0 1 10 0 0 0 1 0 0 1
3 0 0 0 0 0 1 0 11 0 0 0 1 0 1 0
4 0 0 0 0 0 1 1 12 0 0 0 1 0 1 1
5 0 0 0 0 1 0 0 13 0 0 0 1 1 0 0
6 0 0 0 0 1 0 1 14 0 0 0 1 1 0 1
7 0 0 0 0 1 1 0 15 0 0 0 1 1 1 0
8 0 0 0 0 1 1 1 16 0 0 0 1 1 1 1
Connections
7. Input 7
8. Input 8
12. Input 7 & 8 -ve
5. Input 5
6. Input 6
11. Input 5 & 6 -ve
1. Input 1
2. Input 2
9. Input 1 & 2 -ve
3. Input 3
4. Input 4
10. Input 3 & 4 -ve

Sensata Technologies 4 220808
Calibration
The ISOSLICE-2 has an LED that shows which mode it is in.
Green run
Red learn span point
Amber learn zero point
Calibration of a channel:
In run, mode select the input to be calibrated
Calibrate the span point
Return to run mode
Calibrate the zero point
Return to run mode
Select the Input to be calibrated
Push the raise or lower button when the LED is green. The LED will flash red between 1
and 8 times, indicating the input that will be calibrated next.
Calibrate the Span Point
When the input has been chosen push and release both buttons.
The LED will go red.
Put in the span value (e.g., 20mA) into the corresponding input, wait a few seconds for the
input to be averaged to a stable level then push the raise button to confirm that the input
value is the value for the span at 100%. The Isoslice unit will check if it is using the most
appropriate gain setting for theADC. If it is, the span point has been learned.
If the gain is not right, it will change the gain setting (green flash) then the red led will flash.
Push the raise button again to make it learn the input value with the new gain setting.
There are 8 possible gain settings, so it may be necessary to repeat this process a few
times. When the led stays red after the button has been pressed, the span point has been
learned.
Push and release both buttons to return to run mode. The LED will go off briefly (to
indicate it has learned and saved a new value) and then change to green.
Calibrate the Zero Point
Push and release both buttons
The LED will change from green to amber.
Put in the zero value (e.g., 4mA) into the corresponding input, wait a couple of seconds for
the input to be averaged to a stable level then push the raise button to confirm that the
input value is the value for the zero at 0.00%.
Push and release both buttons, the led will again go off briefly and then change to green.
Check the calibration has been successful by varying the input and confirming the value
shown on the Z-Port or E-100 display for the corresponding input and channel is correct.