SenTech STC-400 Series User manual

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 1
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com
Industrial B&W CCD Camera
STC-400, STC-400L, STC-SS400 Series
Operating Manual

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 2
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 3
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Precaution ............................................................................... 4
1. Preface ................................................................................ 4
2. Contents of Box .................................................................. 5
3. Features ............................................................................. 5
4. Camera Specifications ....................................................... 6
5. Major Operating Controls and Functions .............................. 7
5.1 Camera Board Layout .................................................... 10
5.2 Rear Panel ................................................................... 10
5.3 12 Pin Connector Pin-Out .............................................. 11
5.4 Internal Switches ........................................................ 11
6. CCD Pixel Configuration ...................................................... 13
7. Sync. Output Timing Chart ................................................ 15
8. External Sync. Input Pulse ................................................. 15
9. CCD Spectrum Response Curve ......................................... 16
10. Optional Components and Use ......................................... 16
11. Dimensions ..................................................................... 17
12. STC-400 Series Product Family ......................................... 20
Table of Contents

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 4
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Precaution
• Handle the camera with care. Do not abuse the camera. Avoid striking or
shaking it. Improper handling or storage could damage the camera.
• Do not pull or damage camera cable.
• During camera use, do not wrap the camera unit in any material. This will
cause the internal temperature of the unit to increase.
• Do not operate camera in wet areas and do not expose camera to
moisture.
• Do not operate camera beyond its maximum operating temperature,
humidity and power source ratings.
• To prevent dust or contamination from entering the CCD or filter area,
which could scratch or damage this area, keep lens or lens cap on camera
when camera is not in use.
• Do not expose the camera to the following conditions:
- Wet, moist and/or high humidity areas
- Hot direct sunlight
- High temperature areas
- Near objects that release strong magnetic or electric fields
- Strong vibration
• When cleaning the camera, use a soft cloth to clean the external areas of
the camera. Use a pressured air spray to clean the surface of the glass.
Do not scratch the surface of the glass.
• Use only a REGULATED POWER SUPPLY and supply the power with the
specified voltage.
1. Preface
This camera is designed for visual measurement and microscopic applications. Its very
small package design allows it to be installed in very limited spaces. The video output
signal is obtained simply by applying 12Vdc power supply. Various combinations of
performance parameters can be obtained by setting the internal switches. These settings
will enable the camera to be suitable for many different applications.

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 5
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
2. Contents of Box
a. Contents of box
Content QTY
Camera 1
Application Manual 1
b. Optional parts
Power connector (HR-10A-10P-12S)
Power connector and cables assembly
(2m:10W-02, 3m:10W-03, 5m:10W-05, 10m:10W-10)
Tripod adapter with 1/4" 20 UNC screw thread hole (TP-300)
3. Features
The STC-400 Series is a collection of products to fit a wide variety of
applications. The STC-400 Series comes in 1/3” and 1/2” CCD formats and in
compact, remote head, and “L” shaped camera housings. WIth selectable shutter
speeds from 1/60th to 1/10,000th of a second, the STC-400 can capture scenes
and virtually and speed crisply and clearly.
•High picture quality
1/2” 380,000 pixel CCD (EIA) or 440,000 pixel CCD (CCIR). High resolution
picture of 570H x 485V TV line (EIA) or 560H x 575V TV line (CCIR) at frame
accumulation mode.
•Extremely small size
31(W) x 29(H) x 73(D) mm, Weight 85g (STC-400/405)
(1.22”(W) x 1.14”(H) x 2.87”(D)), Weight 3.0 oz (STC-400/405)
31(W) x 45(H) x 87(D) mm, Weight 100g (STC-400L/405L)
(1.22”(W) x 1.77”(H) x 3.43”(D)), Weight 3.5 oz (STC-400L/405L)
•Clock Output
14.31818MHz (EIA), 14.1875MHz (CCIR) pixel clock output.
•Electronic shutter
Highest shutter speed of 1/10,000 sec. For clear image of high speed moving
target.
•Gamma
0.45 or 1 switchable.
•Gain switch
Gain is selectable from 0 to 25dB via the rear panel switches.
•Accumulation mode switching
Field or frame accumulation mode is selectable by the internal switch.

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 6
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
4. Camera Specifications
Signal Format: EIA (STC-400, STC-410, STC-400L, STC-410L)
CCIR (STC-405, STC-415, STC-405L, STC-415L)
Image Sensor: 1/2” IT CCD (STC-400, STC-405)
1/3” IT CCD (STC-410, STC-415)
Total Picture Element: EIA: 811(H) x 508(V)
CCIR: 795(H) x 596(V)
Effective Picture Element: EIA: 768(H) x 494(V)
CCIR: 752(H) x 582(V)
Chip Size: 7.95mm(H) x 6.45mm(V)
Cell Size: EIA: 8.40µm(H) x 9.80µm(V)
CCIR: 8.60µm(H) x 8.30µm(V)
Optical Black: Horizontal, Front: 3 pixel, Back: 40 pixel
Vertical, Front: 12 pixel, Back: 2 pixel
Scanning Area: EIA: 6.45mm(H) x 4.84mm(V)
CCIR: 6.46mm(H) x 4.83mm(V)
Sync. System: Internal/External (Auto switching)
Scanning System: 2:1 interlace
Horizontal Resolution: EIA: 570 TVL
CCIR: 560 TVL
Vertical Resolution: EIA: Frame accumulation: 485TVL
Field: accumulation: 350TVL
CCIR: Frame accumulation: 575TVL
Field: accumulation: 410TVL
S/N Ratio: 56dB (ƒÁ=Off, Gain=0dB)
Minimum Illumination: 0.05 Lux @ F1.2
Video Out: 1 Vp-p / 75Ω
Power Voltage: 10 - 12Vdc
Power Consumption: Approximately 180mA
Operating Temperature: -10°C ± 45°C (14°F ± 113°F)

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 7
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
STC-400 Series
•STC-400 is 1/2”, STC-410 is 1/3”
•B/W 768(H) x 494(V) IT CCD
•Available in EIA & CCIR Formats
•570 TV LInes Horizontal Resolution
•2:1 Interlace
•Field/Frame Integration
•Sync: Internal/External
•Gamma 0.45, 1.0 Switchable
•Pixel Clock Out
•Gain: Fixed/Manual (0-25dB)
• >56dB S/N Ratio (Gain Off)
•Fixed Shutter (8 steps) 1/60 (1/50) to 1/10,000 second
•Minimum Illumination 0.05 Lux @ F1.2, Gain ON, 50 IRE
•Available with or without I/R Filter
•C-Mount Lens Mount
•Dimensions: 31(W) x 29(H) x 73(D)mm
(1.24” x 1.16” x 2.92”)
•12V DC Power
STC-SS400 Series
•STC-400L is 1/2”, STC-410L is 1/3”
• Same basic features and specifications as STC-400 Series
• C-Mount Lens Mount
• Dimensions: 31(W) x 45(H) x 73(D)mm
(1.24” x 1.8” x 2.92”)
STC-SS400 Series
• STC-SS400 is 1/2”, STC-SS410 is 1/3”
• Same basic features and specifications as the STC-400
Series
• C-Mount Lens Mount
• Head Dimensions: 31(W) x 29(H) x 38(D)mm
(1.24” x 1.16” x 1.52”)

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 8
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Image Related Specifications:
Accumulation mode Frame / field
(Internal switch switchable, Factory set up=Field)
γγ
γγ
γ Correction 0.45 / 1 (Internal switch switchable, Factory set up=1)
Gain Fixed/Manual (0dB – 25dB) switchable
Shutter speed:
EIA: 1/60, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000 (Factory set up=1/60)
CCIR: 1/50, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000,
1/10000 (Factory set up=1/50)
Sync. Related Specifications:
Internal Sync. Mode:
Original clock frequency:
EIA: 28.63636MHz
CCIR: 28.37500MHz
H. Sync. Frequency:
EIA: 15.734KHz
CCIR: 15.625KHz
V. Sync. Frequency:
EIA: 59.94Hz
CCIR: 50.00Hz
External Sync. Mode:
Input Signals: HD/VD (2Lines)
Note: Requires 2 line inputs to select external
sync.mode.
Input Signal Level: HD/VD 2 – 5Vp-p Negative polarity
Switchable 75Ωor High Impedance
H. Sync. Allowance:
EIA: 15.734kHz + 1.0%
CCIR: 15.625kHz + 1.0%

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 9
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Sync. Output Signal:
HD: 2 - 5Vp-p
VD: 2 - 5Vp-p
Clock: 2.5Vp-p/75Ω
EIA: 14.31818MHz
CCIR: 14.1875MHz
External Output Connector:
Hirose 12P connector (HR10-10R-12PA)
Mechanical Specifications
Lens Mount C-mount
Optical Center Allowance Less than +10%
Case Color Black
Dimensions (excluding camera mount, connectors and lens)
STC-400/405 31(W) x 29(H) x73(D)mm
(1.24” x 1.16” x 2.92”)
STC-400L/405L 31(W) x 45(H) x87(D)mm
(1.24” x 1.8” x 3.48”)
Weight
STC-400/405 85g (3 oz.)
STC-400L/405L 100g (3.53 oz.)
Vibration Resistance 7G
5. Major Operating Controls and Functions
Important Note: There must be NO POWER to the camera when removing the cover.
Please remove the cover. The following diagram shows the internal structure of the
camera. Disconnect power before opening the camera or removing the cover.

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 10
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
5.1) Camera Board Layout
5.2) Rear Panel
- 12-Pin Connector for Power and Control Signals
Connector for power, external sync signals, and video output. This
connector is usually connected to the power supply, sync signal generator
(or sync source), and video monitor. Please see following page for the 12-
Pin connector’s pin assignments.
- Manual Gain Control Adjustment
When the Gain Select Switch is in the “Manual” mode, this gain of the
video amplifier is adjusted by turning this adjustment. The user can adjust
the gain of the camera from 0 to 25 dB as desired.
- Gain Select Switch (Manual or Fixed)
Manual gain mode is selected by setting this switch to the left. Fixed gain
is selected by setting this switch to the right (factory setting default).
Manual gain value is set by the (B) “Manual Gain Control Adjustment”
(See Above).
- Video Output Connector (BNC)
Video signal output connector for the camera’s composite monochrome signal.

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 11
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
5.3) 12-Pin Connector Pin-Out
Pin No. Internal Sync External Sync
1 GND GND
2 +12Vdc +12Vdc
3 Video GND Video GND
4 Video Out Video Out
5 HD GND HD GND
6 HD Out HD In
7 VD Out VD In
8 Clock GND Clock GND
9 Clock Out Clock Out
10 GND GND
11 +12Vdc +12Vdc
12 VD GND VD GND
Note: The mating connector is the
Hirose HR10A-10P-12S
5.4) Internal Switches
Up: 75Ω
Down: High Impedance
Left Position
(Towards the Front of Camera):
Internal Sync. Mode
Right Position
(Towards the RearofCamera):
External Sync. Mode
Note: When this switch is set at the external mode position, camera detects existence
of external sync. input signal. If there is no external sync. input signal, the camera
switches to internal sync. mode automatically.
A) Impedence Switch of HD/VD Signals
B) Synchronization Selection (Internal/External) Switch
Impedence Switch of HD/VD Signals

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 12
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
C) Camera Mode/Operation Switch
(1) Frame Integration Mode
Mode EIA CCIR SW1 SW2 SW3 SW4 SW5
Frame 1/30 1/25 Either Either Either ON ON
Frame 1/60 1/50 OFF OFF OFF OFF ON
Frame 1/100 1/120 ON OFF OFF OFF ON
Frame 1/250 1/250 OFF ON OFF OFF ON
Frame 1/500 1/500 ON ON OFF OFF ON
Frame 1/1,000 1/1,000 OFF OFF ON OFF ON
Frame 1/2,000 1/2,000 ON OFF ON OFF ON
Frame 1/4,000 1/4,000 OFF ON ON OFF ON
Frame 1/10,000 1/10,000 ON ON ON OFF ON
Shutter Speed Switch Settings
(2) Field Integration Mode
Mode EIA CCIR SW1 SW2 SW3 SW4 SW5
Frame 1/60 1/50 Either Either Either ON OFF
Frame 1/60 1/50 OFF OFF OFF OFF OFF
Frame 1/100 1/120 ON OFF OFF OFF OFF
Frame 1/250 1/250 OFF ON OFF OFF OFF
Frame 1/500 1/500 ON ON OFF OFF OFF
Frame 1/1,000 1/1,000 OFF OFF ON OFF OFF
Frame 1/2,000 1/2,000 ON OFF ON OFF OFF
Frame 1/4,000 1/4,000 OFF ON ON OFF OFF
Frame 1/10,000 1/10,000 ON ON ON OFF OFF

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 13
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
(3) Gama Setting (1.0 or 0.45)
6. CCD Pixel Configuration
(A) Horizontal Pixel Configuration

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 14
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
(B) Vertical Pixel Configuration - 2:1 Interlace, Frame Accumulation
(C) Vertical Pixel Configuration - 2:1 Interlace, Field Accumulation

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 15
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
7. Sync Output Timing Chart
8. External Sync Input Pulse
HD/VD Input Pulse Requirements: 75Ω: 4±1Vp-p
High Impedence (10KΩ): 5±5Vp-p

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 16
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
9. CCD Spectrum Response Curve
10. Optional Components and Use
IR Cut Filter
When the camera is aimed toward a strong light source such as sun or
fluorescent light, usually vertical smear appears in the screen. This is a
typical phenomenon of interline transfer type CCD. IR cut filter is an
effective device to reduce this smear. IR cut filter built-in models are
also available.
Power Connector
The mating connector for “12-Pin Connector for power and control signal”
(Hirose: HR10A-10P-12S) is available as an optional part. Please wire all
necessary connections according to 6-2.
Pre-Wired Power Connector
The above mating connector with pre-wired cables is also available as an
optional part.This makes connection works to external devices easier.
Tripod Adapter
For easy camera installation, an optional adapter with 14” 20 UNC screw thread
hole is available. With this adapter, the camera can be installed to standard
tripod or other standard camera mounts.
Note:
1. Requires four (4) each M2 screws to mount the TP-300 to the bottom of the
camera. (comes with TP-300 when purchased through SenTech)
2. Maximum length of the four screws must be 7mm

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 17
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
11. Dimensions
STC-400
Note: Measurements are given in mm

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 18
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
Note: Measurements are given in mm
11. Dimensions (Continued)
STC-400L

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 19
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
STC-SS400
CCU
11. Dimensions (Continued)
STC-SS400
Head
Note: Measurements are given in mm

Sensor Technologies America, Inc.
1345 Valwood Parkway, Suite 320 :: Carrollton, Texas 75006
Phone: [phone] :: Fax: [phone] :: Toll Free: 1 (877) - SENTECH (736-8324)
www.SentechAmerica.com 20
STC-400 & STC-400L Series
Operating Manual
Rev. 0.1 - Created July 15,2005
12. STC-400 Series Product Family
Series Model Product Description
STC-400 STC-400HOL EIA, 1/2” Monochrome Hi-Resolution CCD
STC-410HOL EIA, 1/3” Monochrome Hi-Resolution CCD
STC-405HOL CCIR, 1/2” Monochrome Hi-Resolution CCD
STC-415HOL CCIR, 1/3” Monochrome Hi-Resolution CCD
STC-400A EIA, 1/2” Monochrome Hi-Resolution CCD w/IR Cut Filter
STC-410A EIA, 1/3” Monochrome Hi-Resolution CCD w/IR Cut Filter
STC-405A CCIR, 1/2” Monochrome Hi-Resolution CCD w/IR Cut Filter
STC-415A CCIR, 1/3” Monochrome Hi-Resolution CCD w/IR Cut Filter
STC-400L STC-400L EIA, 1/2” Monochrome Hi-Resolution CCD “L” Shaped
STC-410L EIA, 1/3” Monochrome Hi-Resolution CCD “L” Shaped
STC-405L CCIR, 1/2” Monochrome Hi-Resolution CCD “L” Shaped
STC-415L CCIR, 1/3” Monochrome Hi-Resolution CCD “L” Shaped
STC-SS400 STC-SS400 EIA, 1/2” Monochrome Hi-Resolution CCD Remote Head (Back*)
STC-BS400 EIA, 1/2” Monochrome Hi-Resolution CCD Remote Head (Bottom*)
STC-LS400 EIA, 1/2” Monochrome Hi-Resolution CCD Remote Head (Left*)
STC-RS400 EIA, 1/2” Monochrome Hi-Resolution CCD Remote Head (Right*)
STC-TS400 EIA, 1/2” Monochrome Hi-Resolution CCD Remote Head (Top*)
STC-SS405 CCIR, 1/2” Monochrome Hi-Resolution CCD Remote Head (Back*)
STC-BS405 CCIR, 1/2” Monochrome Hi-Resolution CCD Remote Head (Bottom*)
STC-LS405 CCIR, 1/2” Monochrome Hi-Resolution CCD Remote Head (Left*)
STC-RS405 CCIR, 1/2” Monochrome Hi-Resolution CCD Remote Head (Right*)
STC-TS405 CCIR, 1/2” Monochrome Hi-Resolution CCD Remote Head (Top*)
STC-SS410 EIA, 1/3” Monochrome Hi-Resolution CCD Remote Head (Back*)
STC-BS410 EIA, 1/3” Monochrome Hi-Resolution CCD Remote Head (Bottom*)
STC-LS410 EIA, 1/3” Monochrome Hi-Resolution CCD Remote Head (Left*)
STC-RS410 EIA, 1/3” Monochrome Hi-Resolution CCD Remote Head (Right*)
STC-TS410 EIA, 1/3” Monochrome Hi-Resolution CCD Remote Head (Top*)
STC-SS415 CCIR, 1/3” Monochrome Hi-Resolution CCD Remote Head (Back*)
STC-BS415 CCIR, 1/3” Monochrome Hi-Resolution CCD Remote Head (Bottom*)
STC-LS415 CCIR, 1/3” Monochrome Hi-Resolution CCD Remote Head (Left*)
STC-RS415 CCIR, 1/3” Monochrome Hi-Resolution CCD Remote Head (Right*)
STC-TS415 CCIR, 1/3” Monochrome Hi-Resolution CCD Remote Head (Top*)
(*=Cable Orientation in Relation to the Remote Head)
OEM Special OEM versions of the STC-400 series are available, Please contact Sentech for
more details and inofrmation