Seon Mobile Surveillance Explorer Premier Mobile Digital Video Recording... User manual

700-0047 R002
*700-0047* 1
Explorer® Premier Mobile Digital Video Recording (DVR) System
Installation and Quick Start Guide
The Explorer Premier DVR is installed with a mounting plate, a security front cover with lock set, and a cable cover which ensures that the
back panel connections are tamper proof. The cable cover has three cable grommets to allow for wiring to be inserted.
To mount the DVR in a suspended horizontal mount under a seat or on a shelf, use the optional mounting bracket.
Check that you have all the system components and inspect the units for any scratches or damage.
You will need these materials to complete the installation:
• DVR keys for securing the removable hard drives
• Front cover keys for the security front cover
• Key or security screw driver (Phillips screw driver)
Package Contents (typical) for Premier
The contents of a typical installation package are listed below. The actual contents of your installation package may vary.
Explorer Premier DVR with security front cover and cable
cover, media cartridge hard drive Cameras × 8 Ignition harness wire

Quick Installation Guide
2 700-0047 R002
Premier Plus components
Power input harness with in-line fuses SA external microphone (optional) IR Illuminator (optional)
Smart-Link™ module for signal interfaces Smart-Link-to-DVR connection harness (identical
connectors) Signal harness
Diagnostic indicator/alarm button (extension wiring
not shown) Speed cable Alarm input harness
GPS receiver (optional) Inertia sensor (optional)

Quick Installation Guide
700-0047 R002 3
Figure 1 Typical Plus System
Explorer® Premier
Typical Plus System Setup
Vehicle Electrical Interface
Peripherals Seon System
Remote Microphone*2
Smart-Link™
Supports Eight Cameras
IR Illuminators
Auxiliary Power
GPS Receiver *1 2 wires
Vehicle + 12V (red)
Vehicle Ground (black)
CONSTANT POWER
8 wires
Alarm 1 (orange)
Alarm 2 (blue)
Alarm 3 (violet)
Alarm 4 (gray)
Alarm 1-4 Ground (black)
4 wires
1A
10A
ALARMS
Red - Call Seon if using hall sensor
Green - Speed sensor high
Black - Speed sensor low
3 wires
SPEED
Diagnostic Indicator/
Alarm Button 4 wires
Explorer Premier DVR Rear Panel
*1 For better speed tracking, Seon recommends using a GPS receiver.
*2 If camera 1 and/or camera 2 are connected to only cameras, then the
Premier can support 2 remote microphones.
2 wires
Vehicle Switched + 12V (yellow)
Vehicle Ground (black)
SWITCHED POWER
4 wires
2 wires
Left Turn (black)
Inertia Sensor (green)
Brake Signal (red)
Warning (brown)
Right Turn (white)
5 wires
SIGNALS
i.e. Inertia Sensor
i.e. Smart-Reach™ Mobile (Wi-Fi)
CAMERA8CAMERA7CAMERA6CAMERA5CAMERA4CAMERA3CAMERA2CAMERA1
POWER
SMART
LINK™ AUX
POWER1
AUX
POWER2
AUDIO OUT VIDEO OUT CONTROL LAN2 LAN3
AUDIO1 AUDIO2
POWER IN
SIGNALS
ALARMS AUX.
POWER
POWER OUT
TO DVR
INDICATOR
PANEL
GPS
CAN
GPS
DB-9
SPEED

Quick Installation Guide
4 700-0047 R002
Installation
The DVR typically ships with the security front cover and the cable cover on.
Horizontal Installation with the Mounting Plate
To install the Premier DVR:
1Select an appropriate mounting location. For the dimensions and locations of the mounting holes, see Figure 11.
2Unlock the door lock and remove the security front cover from the unit to access the front panel.
The front cover key is required to unlock the door latch on the front cover. To unlock and remove the front cover, insert the front cover key
and turn clockwise. Turn the door latch counterclockwise. Remove the security front cover from the unit. The front cover sits on two pins.
See Figure 2.
3Ensure the two hard drives are installed in the DVR and locked in place.
4Remove the cable cover from the unit. Determine where the wiring and camera cables will enter the unit: on the left side, right side or
back.
The secure cable cover ensures that the back panel connections are tamper proof once the DVR is completely installed. Three cable
Figure 2 Security front cover with locking door latch
Pin × 2

Quick Installation Guide
700-0047 R002 5
grommets on the cable cover allow the wiring to be inserted from different sides. The cable cover sits on two pins. See Figure 3.
5Remove the necessary knockout (s), insert plugs and cable grommets.
6Use the mounting plate to mark the desired position of the DVR and drill the 6 mounting holes. Make sure the front flange is facing
forward. This is where the DVR is attached to the mounting plate with security Torx screws.
7Fasten the mounting plate to the mounting surface using the six #10 × ¾ screws provided.
8Slide the DVR onto the rails of the mounting plate. See Figure 4. (Only the rails are shown to highlight the detailed area.)
Figure 3 Cable cover removed from DVR
Figure 4 Mounting plate front view. sliding the DVR on, attaching security Torx screws
Pin × 2

Quick Installation Guide
6 700-0047 R002
9Connect the necessary components. Attach the cable cover.
10 Fasten the two security Torx screws to the mounting plate. This secures the DVR onto the mounting plate.
Figure 5 Sliding the DVR onto the mounting plate
Figure 6 Attaching DVR to mounting plate with security Torx screws

Quick Installation Guide
700-0047 R002 7
11 Figure 7 shows a completed installation with security front cover, cable cover and the mounting plate.
Horizontal Installation with the Mounting Bracket
Use the mounting bracket with the mounting plate to install the Premier DVR in a suspended horizontal orientation only.
1Fasten the mounting plate to the mounting bracket using the six screws provided. See Figure 8.
Figure 7 Explorer Premier DVR secured
Figure 8 Fastening mounting plate to mounting bracket
Locking front cover
Cable cover
Door latch

Quick Installation Guide
8 700-0047 R002
2or Install the mounting bracket in desired location and fasten the mounting plate with six screws to the bracket flanges.
3Determine where the wiring and camera cables will enter the unit: on the left side, right side or back.
4Install the DVR and make the necessary connections.
5Attach the cable cover.
6Ensure the two hard drives are installed in the DVR and locked in place.
Installing the Cameras
If you have purchased cameras from Seon Design, install the cameras according to the documentation that shipped with the product. The
Premier accommodates a 6-pin Molex connector. The camera cable can be surface run or concealed.
• If the installation is surface run, ensure that the camera cable is secured at multiple points and is protected from sharp corners.
• If the cable is concealed, it can be pulled from either end.
Feed the cable through one of the large cable grommets one at a time, or cut the grommet at the top and slide the cables into the grommet.
Figure 9 Mounting bracket with DVR installed

Quick Installation Guide
700-0047 R002 9
Installing the Smart-Link™ Module and Connecting the Constant and
Switched Power Harness
The Premier uses the external Smart-Link module to provide interface connections to a variety of different signals. The Smart-Link is
designed to be installed into the electrical compartment of a vehicle, reducing the number of cables that connect to the DVR and reducing
the lengths of harnesses and cables that connect to the vehicle systems. If you need assistance in determining a suitable location to mount
the Smart-Link, contact Customer Service at Seon Design. (The dimensions for the Smart-Link are provided on page 13.)
1Mount the Smart-Link on a vertical surface to avoid having liquids pool on the bottom.
2Mount the Smart-Link using the four #10 × ¾" sheet metal screws or the four #10 × ¾" self-drilling screws.
3Connect the constant and switched power harness as shown in Figure 1, “Typical Plus System” on page 1–3.
Installing the GPS Receiver
If you have not purchased a GPS receiver or if you wish to install the GPS receiver at a later time, please proceed to “Installing the
Diagnostic Indicator/Alarm button”. Seon Design provides several models of GPS receivers designed to work with the Premier. Contact
your sales representative at Seon Design for the GPS receiver best suited for your application.
Installing the Diagnostic Indicator/Alarm button
If you wish to install the diagnostic indicator/alarm button at a later time, please proceed to “CAN Network” on page 1–11.
The Smart-Link module has an interface for a diagnostic indicator/alarm button (indicator panel). The basic version consists of a heavy
Important: The in-line automotive fuse holders consist of a black plastic piece with an attached cap. Pull the cap apart, install the fuse and snap
the holder back together. The fuse holders protect the:
• yellow ignition trigger wire on the constant and switched power harness. The ignition trigger fuse holder uses the 1 A automotive blade fuse.
• red battery positive wire on the constant and switch power harness. The red positive fuse holder uses the 10 A automotive blade fuse.
• Use the butt-splice connectors to connect the fuse holders to their respective wires.
CAUTION
To ensure proper performance, connect the red and black power wires to points as close to the battery as possible. Never connect the
ground wire (black wire) to the vehicle chassis by drilling a hole into a panel and using a sheet metal screw. The ground
connection will be corroded very quickly and the performance will be compromised.

Quick Installation Guide
10 700-0047 R002
duty, vandal-resistant switch with an green indicator ring around the switch button. The diagnostic indicator/alarm button has a weather-
sealing gasket attached to prevent water penetration. The diagnostic indicator/alarm button is supplied with a 12" cable and connector. A
10-foot extension cable is provided as a standard accessory. Contact your sales representative at Seon to order a different length cable.
1Drill a ¾" hole in the desired location. Ensure that the area behind the hole is clear of obstructions before drilling.
2Remove the mounting nut from the diagnostic indicator/alarm button.
3If you have purchased the video recording label, install the label between the button and the dashboard.
4Feed the connector and cable through the mounting hole and reattach the nut.
Pressing the alarm button of the diagnostic indicator/alarm button causes an alarm event to be recorded by the DVR. The button
corresponds to Alarm 1 on the Smart-Link alarm harness. The color of the indicator ring indicates the status of the DVR. See Table 1.
Hardware Installation Final Checklist
Harnesses (Camera, recorder, and accessories)
• Check for proper slack.
• Check that the cables and harnesses are properly secured.
• Check that sharp metal edges are not touching the cables or harnesses.
• Check that all the cables and harnesses are neat and tidy.
• Check that the connections are solid (no shorts).
Cameras
• Check for tight mounting of camera. Check the internal harness connections.
• Check that the lid is properly seated on the gasket and secured tightly.
• Check the camera (s) field of view.
Table 1 Diagnostic indicator/alarm button ring color
Ring color and activity Function
No green light No power to the DVR, or ignition is not on.
Flashing green The DVR is powered up, but not recording.
Solid green The DVR is powered up and recording.

Quick Installation Guide
700-0047 R002 11
Recorder
• Check for tight mounting of hardware.
• Confirm that the cable grommet is properly installed.
• Check that all connections are tight.
System
• Install the fuses.
• Plug the video monitor into the DVR.
• Power up the system.
• Confirm that all the cameras and audio sources are operating properly.
• Confirm that all the status indicators react properly: Hard drive power indicator, Hard drive (lock and access), Voltage, temperature
or system alarms
• Switch to temporary power by toggling the front panel POWER button with vehicle ignition turned OFF.
• Test audio/video record and test audio/video playback.
• Configure the menus per the end-user specifications. See Explorer Premier Mobile DVR System User Guide (p/n 700-0046).
• Fasten the front cover and cable cover on the unit.
Inertia Sensor
The inertia sensor is a programmable accelerometer and impact sensor that can measure rapid acceleration or deceleration, abrupt
movement in bus braking or turning which can lead to complaints or injury claims. Video footage recorded with the sensor provides
valuable information for reviewing incidents and for training purposes as well. The inertia sensor has adjustable trigger thresholds which
can be wired to trigger alarms and signals. Contact your sales representative at Seon Design for inertia sensor options.
CAN Network
The Premier has a built-in CAN interface for connecting to J1939 compliant vehicle networks. J1939 is a Society for Automotive Engineers
(SAE) specification for network communication in a vehicle. Seon Design can factory program the Smart-Link module to accept ten signals
from the large selection available on a vehicle. Contact your sales representative at Seon Design to discuss the CAN interface.
Wireless Network
Contact your sales representative at Seon Design for wireless network options.

Quick Installation Guide
12 700-0047 R002
Physical Specifications
Explorer Premier DVR
Figure 10 shows the physical specifications of the Premier. Table 2 shows the weight and material of the DVR.
Important: Specifications are subject to change without notice.
Figure 10 Explorer Premier DVR dimensions
Table 2 Explorer Premier DVR physical specifications
Weight 15 lb (6.8 kg)
Material Aluminum and steel, powder coated black paint
321 mm
125
8
425 mm
164
3in
in
442 mm
17 13
32 in
315 mm
12 3
8in
127 mm
5 in

Quick Installation Guide
700-0047 R002 13
Mounting Plate and Smart-Link™ Module
Customer Service Contact Information
Toll free telephone [phone] or telephone [phone] Email: [email protected]
©April 2010. Seon Design Inc. All rights reserved. Printed in Canada www.seon.com
Figure 11 Mounting plate dimensions and Smart-Link module
Table 3 Smart-Link physical specifications
Height × Width × Depth 5.875" × 3.25" × 0.875" (150 × 83 × 23 mm)
Weight 5.6 oz (160 g)
Material 14 GA aluminium, anodized black
28 mm
13
32
in 229 mm
9 in
229 mm
9 in
229 mm
9 in
4
3
32
104 mm
in

Quick Installation Guide
14 700-0047 R002