SEOWON INTECH SLC-120T42OGA User manual

AC Code
(100~240V)
AC IN
PoE Injector
LAN Cable for PC or
WiFi Access Point
LAN
Cable
Outdoor CPE
LTE Network Outdoor CPE
SLC-120T42OGA
Quick Installation Guide
Step 2 (Installing USIM Card)
Carefully insert the USIM Card into USIM slot.
Assembly sequence optimization
Mounting Conguration
You need the following :
One Bracket
Mounting Bar (2ea)
Mounting U-Bolt (2ea)
Bolts (4ea)
Toothed lock washer (4ea)
1
3
2
4
5
Bolt M3 (6ea)
Nuts (4ea)
Spring Washers (4ea)
Washer (4ea)
6
7
8
9
www.seowonintech.co.kr
1
5
3
2
4
Remove the cap.
Put A, B, Cap and Aluminum plate to cable line in order.
Plug the cable line into the LAN hole of outdoor CPE.
Connect A and B in order.
Lastly, connect Cap to Aluminum plate by turning.
Step 3
Remove the cap by turning. Then follow the next steps
as shown below.
Package Contents Connection Diagram
Mounting Kits
AC Code
(100~240V)
LAN Cable PoE
Quick
Installation
Guide
3
4
2
1
56
7 8 9
Step 1
Remove the two Bolt M3 from the outdoor CPE.
* Remaining 6 screws are enclosed in the mounting kits as
6
(2ea)
USIM
card
Cable line Cap B A
Aluminum plate
CAUTION : The surface of IC(metal)
should be facing downward from
the USIM card.
IC
USIM card
Data IN
Data &
Power Out
NOTE : It is recommended to
use the accessory provided.

Log-in to Web Interface
- Go to WEB "http://192.168.1.1" then press ENTER to access the login screen.
- The default one is user for both User Name and Password.
LED Presentation
Status icon & LED indicator
Boot in progress Blinking Yellow LED (1), Blinking period = 1sec
Network connec-
tion
Number of LED depending on signal strength
- Most Strong Signal : Five yellow LED
- Strong Signal : Four yellow LED
- Middle Signal : Three yellow LED
- Weak Signal : Two yellow LED
- Very Weak Signal : One yellow LED
Step 5
Attach item 1 to the back side of the device
using item 4 as shown.
(Insert item 5 into item 4 before installing)
Step 6
Install the device to pole using item 2 & 3,
tighten the bracket by using item 7 & 8 & 9.
Step 7
Adjust the device, using the dierent position
on the bracket. Check the LED light (1~5).
Step 4
Assemble the Aluminum plate and outdoor CPE
using the screws Bolt M3(8ea).
6
1
5
4
2
3
8 97
RESET Button (When the device turned On)
- Press the reset button once : Device reboot
- Press and hold the reset button 5sec : Factory reset
RESET Button
Turn left: Open
Turn right: Closed
NOTE : If you forget the Login password for the
Outdoor CPE or IP address after making changes,
use the reset button to restore the Outdoor CPE to its
original factory default settings.
(8ea)
LAN
Cable line

Legal Information
FCC Part 15.105
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Part 15.21
Changes or modications not expressly approved by the manufacturer (or party
responsible) for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement:
The output power from the device is below the threshold for requiring RF exposure
evaluation and may be used in portable conditions within 20cm of the body.
FCC ID: V7MSLC-120T42OGA

Warranty Information
This product is the result of high-class craftsmanship based on strict quality control
procedures.
• In case of Product failure or malfunction during normal usage, your product will be
repaired free of charge within the Limited Warranty period.
• The Consumer shall bear any labor or parts charges not covered by this Limited Warranty.
• At the request for repair, you must provide the proof of purchase and the warranty.
• Keep the warranty in a safe location because it is not reissued.
The Consumer shall have no coverage or benets under this Limited Warranty if the
Product has been:
• Subjected to inappropriate use, improper storage, unauthorized repair,
unauthorized modications, neglect abuse, inadequate installation, misuse,
damage caused by shipping, etc.
• Damaged from re, ooding, windstorm, lighting, earthquake, theft, blown fuse,
internet viruses, worms, Trojan Horses, etc.
• Treated with its Product Serial # removed or defaced.
Purchase date
Quality warranty period 1(one) year
Seller
Telephone number
Consumer
Name
Address
Telephone number
E-mail