Ruijie Networks RG-AP130-W User manual

RG-AP130-W Access Point
Quick Installation Guide

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

1.1 Packing List
Table 1-1 Packing List
Item
Name
Quantity
Unit
1
AP130-W Host
1
Set
2
AP130-W Plate Cover (White)
1
Piece
3
RG-AP130-W Access Point Quick Installation Guide
1
Copy
4
Product Warranty
1
Copy
5
Philips Flat Head Screw
2
Piece
6
Hex Socket Screw
2
Piece
1.2 Product Image
Figure1-1 Product Image of RG-AP130-W
Figure1-2 Front View of RG-AP130-W

Figure1-3 Bottom View of RG-AP130-W
Note:
①1000M LAN port (RJ45)
Figure1-4 Side View of RG-AP130-W

Note
①Console (Micro USB)
②Reset button (diam:
1.5mm)
③Power port (powering the
device through the power
adapter)
④RJ45 pass through
port (RJ11 combo)
⑤Key hole
⑥Locking bar hole
The key hole and locking bar hole are used with security accessories.
Figure1-5 Rear View of RG-AP130-W
Note
①1000M PoE uplink port
②RJ45 pass through port
(RJ11 combo)
The access point can be powered either with a DC power adapter or through Power over Ethernet (PoE).
When powering the device through PoE, you need to connect one end of an Ethernet cable to the PoE/uplink port
and the other end to a PoE-capable switch or any power sourcing equipment.
When powering the device through DC power adapter, you need to connect one end of an Ethernet cable to the
PoE/uplink port and the other end to a switch.
The pass through ports (RJ45) on the rear panel and the side panel are directly connected.
1.3 Button and LED Indicators
The LED indicator is inside of top plate cover, and works after you power on the device.
You can also use the quiet-mode and schedule commands on the AP or AC device to configure the quiet time range.

Table 1-2 LED Indicators on RG-AP130-W
State
Frequency
Meaning
Off
N/A
The AP is NOT receiving power. Or the AP is in Do Not Disturb
mode, which can be disabled by software.
Solid green
after fast
blinking
Fast blinking: 2.5Hz
Initialization in progress.
Continuous
fast blinking
green
2.5Hz
1. Initialization in progress.
2. Firmware upgrade in progress. Do not power off.
3. Initialization is complete, but the CAPWAP connection is
faulty.
Slow blinking
green
0.25Hz
Normal operation, and at least one wireless client is associated
with the AP.
Blinking green
1 blinking every 4 seconds
Normal operation, but no wireless clients are associated with
the AP. The device operates in low-consumption mode.
Solid green
N/A
The LAN port is not connected.
Reset button
Press for less than 2
seconds
Reset the system.
Press for more than 3
seconds
Reset the system and restore the factory settings (namely, the
AP is operating in FIT mode).
1.4 Installing the RG-AP130-W Wireless Access Point
Step 1: Remove the 86-type panel from the wall with a screwdriver. (If needed)

Step 2: Connect the Ethernet cable to the UpLNK port on the rear of the access point, and connect the telephone cords to
the pass through port if needed.
Step 3: Align the screw holes on the panel with the screw holes in the wall, use screws to fasten the access point.
Step 4: Attach the frameplate cover as shown in the figure.
The access point is installed.
The access point has 4 different color plate cover options (white, black, silver and gold. White as default delivery).
1.5 Quick Configuration:
Step 1: Access the Web user interface.
In the Fit mode, the IP address of the LAN port and the UpLNK port are 192.168.110.1/24.

In the Fat mode, the IP address of the LAN port is 192.168.111.1/24, and the IP address of the UpLNK port is
192.168.110.1/24.
Step 2: Log into the AP device.
Enter the username and password, click Login.
The default username is admin, and the default password is admin.
Step 3: Perform quick configuration.
By default, the AP works in the Fit mode.
The Homepage displays the basic information of the AP device.

Click the button to perform quick configuration or to switch to the Fat mode.
When the AP is switched to the Fat mode, the Quick Settings page is displayed
The AP device can work in AP access mode or wireless routing mode.
1 ) Select AP Access Mode.
Configure the VLAN and IP address, then click Next.

Configure the WiFi parameters, and click Finish to finish the configuration.

2 ) Select Wireless Routing Mode.
Configure the Internet connection type and related parameters, then click Next.
Configure the WiFi parameters, and click Finish to finish the configuration.