SereneLife SLBSMPMP50 User manual

SubmersibleClean/DirtyWaterPump
SLBSMPMP50-SLBSMPMP50.9-SLBSMPMP100
Powerful Sump Pump, 1980 GPH,
Auto Float Switch with 16 ft. Power Cord Length

www.SereneLifeHome.com1
APPLICATION
This pump is used primarily as cellar pump. When installed in a shaft, the pump
provides protection from ooding. It is also used wherever water has to be
moved from one place to another, e.g. in the home, agriculture, horticulture,
plumbing and many other applications. Not suitable for professional use.
SAFETY FIRST!
• Read this manual and general safety instructions carefully before using the
appliance, for your own safety. Your power tool should only be passed on together
with these Instructions.
• To reduce risk of electrical shock, always disconnect the pump from the power
source before handling or servicing.
• DO NOT pump hazardous materials (ammable, caustic, etc.) unless the pump is
specically designed and designated to handle them.
• DO NOT block or restrict discharge hose, as discharge hose may whip under
pressure.
• DO NOT wear loose clothing that may become entangled in the impeller or other
moving parts.
• Keep clear of suction and discharge openings. DO NOT insert ngers in pump
with power connected.
• Always wear eye protection when working on pumps.
• DO NOT exceed manufacturers recommendation for maximum performance, as
this could cause the motor to overheat.
• DO NOT remove cord and strain relief. Do not connect conduit to pump.
• WARNING! Cable should be protected at all times to avoid punctures, cut, bruises
and abrasions - inspect frequently. Never handle connected power cords with
wet hands.
• WARNING! To reduce risk of electrical shock, all wiring and junction connections
should be made per the NEC or CEC and applicable state or province and local
codes. Requirements may vary depending on usage and location.
• WARNING! Submersible Pumps are not approved for use in swimming pools,
recreational water installations, decorative fountains or any installation where
human contact with the pumped uid is common.
IMPORTANT!
We are not responsible for losses, injury, or death resulting from a failure to
observe these safety precautions, misuse or abuse of pumps or equipment.
When parts are missing or damaged, please contact your dealer.

www.SereneLifeHome.com 2
GENERAL POWER TOOL SAFETY WARNINGS
Read all safety warnings and all instructions. Failure to follow all warnings and
instructions may result in electric shock, re and/or serious injury. Save all warnings
and instructions for future reference. The term "power tool" in the warnings refers
to your mains operated (corded) power tool. Only qualied personnel should
install, operate and repair pump. Any wiring of pumps should be performed by a
qualied electrician.
BEFORE START-UP, NOTE THE FOLLOWING!
• The pump can be connectedto any shock-proof plug which has been installed
according to regulations. The plug must have a supply voltage of 220 V - 50Hz.
Fuse min. 6 Amp.
CAUTION!
When the pump is to be used near swimming pools or garden ponds and in their
area of protection, it must be equipped with a PRCD (residual current circuit breaker)
with a nominal trip current of max. 30 mA (according to VDE 0100, part 702 and 738).
The pump must not be operated while people are in the swimming pool or in the
garden pond! Please contact your electrician!
ATTENTION!
Before starting to run your new submersible pump, please have the following
items checked by an expert:
• Ground connection
• Zero conductor
• Fault current breaker switch must correspond the safety regulations of the power
plants and they must work faultlessly.
• The electrical connections must be protected from moisture.
• If there is danger of ooding, the electrical connections must be taken to higher
ground.
• Circulation of aggressive uids, as well as the circulation of abrasive materials
must be avoided at all costs.
• The submersible motor-driven pump must be protected from frost.
• The pump must be protected from running dry.
• Access on the part of children should also be prevented with appropriate measures.

www.SereneLifeHome.com3
CONSISTENCY
Your submersible pump is designed for the circulation of water with a maximum
temperature of 35°C or 95°F. This pump may not be used for other uids, especially
motor fuels, cleaning uids, and other chemical products!
PARTS DESCRIPTION
1
2
3
4
5
1
2
3
4
5
1. Motor housing
2. Water inlet
3. Water outlet
4. Cable & plug
5. Floating switch
6. Carrying handle
SLBSMPMP50 and SLBSMPMP50.9 SLBSMPMP100

www.SereneLifeHome.com 4
INSTALLATION
The submersible pump is installed as follows:
• In a stationary position with xed pipeline.
• In a stationary position with a exible hose pipe.
Please note!
You should never install the pump by suspending it unsupported from its delivery
pipe or power cable. The submersible pump must be suspended from the specially
provided handle or be placed on the bottom of the shaft. To guarantee that the
pump works properly, the bottom of the shaft must be kept free of sludge and dirt
of all kinds. If the level of water sinks too far, any sludge in the shaft will dry out
quickly and stop the pump from starting up. Therefore it is necessary to check the
submersible motor pump regularly (by carrying out start-up tests). The oater is
adjusted in a way that the pump can immediately be started.
Note!
The pump shaft should have minimum dimensions of 40 x 40 x 50 cm, so that the
oating switch can move freely.
MAINS SUPPLY
Your new submersible pump is equipped with a shock-proof plug according to
regulations. The pump is designed to be connected to a 220V - 50Hz earthed socket.
Make sure that the socket is suciently secured (min.6 Amp.) and is in excellent
condition. Introduce the plug into the socket and the pump is ready to go.
Important Note!
If the mains cable or plug suers any damage from external action, repairs to the
cable should be serviced by a qualied specialist using only standard spare parts.
This will ensure that it meets the required safety standards.
SETTING TO WORK
After having read these instructions carefully, you can set your pump to work,
reconsidering the following item:
• Check if the pump rests on the ground of the shaft.
• Check if pressure cord has been attached properly.
• Check if electrical connection is 110V 60Hz
• Check if the socket is in good condition.
• Make sure that water and humidity can never come to the mains supply.
• Avoid pump running dry.

www.SereneLifeHome.com5
VENTING THE PUMP BEFORE USE
Always ensure that the pump is vented property before commissioning the pump.
Possibly tilting back and forth several times until no more air bubbles appear, wait
at least 15 seconds before the pump to start.
SETTING THE ON/OFF OPERATING POINT
The ON and OFF operating point of the oat switch can be set by adjusting
the oat switch in its latching holder. Before you put the pump into operation,
please check the following:
• The oat switch must be installed so that the levelof the ON operating point and
the level of the OFF operating point can be reached easily and with little force.
To check this, place the pump in a vessel lled with water, raise the oat switch
carefully by hand and then lower it again. As you do so, note whether the pump
switches on and o.
• Make sure that the distance between the oat switch head and the latching holder
is not too small. Proper operation is not guaranteed if the gap is too small.
• When you set the oat switch, make sure that it does not touch the base before
the pump switches o. Caution! Risk of dry-running.
This appliance cannot be used by children or people who are physically, mentally
or developmentally impaired, or people who lack experience or knowledge, except
in case these people receive instruction from a person responsible for their safety,
a supervisor, or by studying the preceding instructions concerning use of this
appliance.
CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the
power plug.
Never use solvents such as petrol, alcohol, ammonia water, etc.
These solvents may damage the plastic parts.
MAINTENANCE GUIDELINES
This submersible pump is an approved, maintenance-free high quality product,
which is subject to severe nal controls. We recommend regular inspection and
maintenance to ensure long equipment life and uninterrupted operation.

www.SereneLifeHome.com 6
Remove the mains plug before all maintenance work.
• When the pump is often transported in the course of operation, it should be
cleaned outwith clear water after every use.
• In case of stationary installation, the function of the bating switch should be
checked every3 months.
• All brous particles which may have built-up inside the pump housing should be
removed with a water jet.
• Every 3 months the shaft ground and as should be cleaned from mud.
• Remove deposits on the oater with clear water.
CLEANING THE IMPELLER
If excessive deposits collect in the pump case you must dismantle the bottom
part of the pump as follows:
1. Remove the intake cage from the pump case.
2. Clean the impeller with clear water.
Important! Do not put down or rest the pump on the impeller!
3. Re-assemble in reverse order.
SERVICE DEPARTMENT
• Damaged switches must be replaced by our after-sales service department.
• If the connecting cable (or mains plug) is damaged, it must be replaced by a
particular connecting cable which is available from our service department.
Replacement of the connecting cable must only be carried out by our service
department (see last page) or by a qualied person (qualied electrician).
STORAGE
• Thoroughly clean the whole machine and its accessories.
• Store it out of the reach of children, in a stable and secure position, in a cool and
dry place, avoid too high and too low temperatures.
• Protect it from exposure to direct sunlight. Keep it in the dark, if possible.
• Don’t keep it in plastic bags to avoid humidity build-up.
ENVIRONMENT
Should your appliance need replacement after extended use, do not discard
it with the household rubbish but dispose of it in an environmentally safe
way. Waste produced by electrical machine items should not be handled like
normal household rubbish. Please recycle where recycle facilities exist.
Check with your Local Authority or retailer for recycling advice.

Incidents Causes Remedies
Pump does not start • NO mains supply
• Floater does not switch
• Check main supply
• Bring oater in a higher
position
NO ow • Inlet sieve is clogged
• Pressure hose in bent
• Clean inlet sieve water jet
• Reset hose
Pump does not
switch o • Floater cannot sink down • Place pump properly on
shaft ground
• Inlet sieve is clogged
• Reduced pumping
capacity by dirty and
aberasive water
• Clean inlet sieve
• Clean pump and replace
worn-out parts
Insucient ow
Pump switches o
after short operation
period
• Thermal cutout stops
pumps due to dirty water
• water too hot, thermal-
cutout stops pumping
• Remove mains plug, clean
pump and shaft
• Make sure that a water
temperature of max. 35°C
(95°F) is not exceed
www.SereneLifeHome.com7
TROUBLESHOOTING
SLBSMPMP50.9 SLBSMPMP100
Power Supply
Qmax
H.Max
Product Dimension
(L x W x H)
400W (0.5HP) 750W (1HP)
1,980 gallon/
H (7,500L/H）
3,302 gallon/
H (12,500L/H）
16.40ft. (5 Meters) 26.25ft. (8 Meters)
6.2’’ X 6.1’’ 12.4’’
–inches
6.2'' x 6.1'' x 13.4''
-inches
SLBSMPMP50
400W (0.5HP)
1,980 gallon/
H (7,500L/H）
16.40ft. (5 Meters)
6.2’’ X 6.1’’ 12.4’’
–inches
MODEL

www.SereneLifeHome.com 8
FEATURES:
• Compatible with Flat PVC Hose in 0.98’’ and 1.26’’ inches
• Screw Thread in NPT1-1/4’’ and NPT5/8’’
• Auto Float Switch: Start/Stop Automatically
• Rugged and High-Quality Materials
• Designed and Manufactures with Valid Safety Requirements
• Lower Noise and Energy-Ecient
• Oil-Free Motor, Requires no Maintenance
• Thermoplastic Body Resists Corrosion
• Great to Drain the Dirty Water from the Pond, Garden Pond, or Water Tanks
• Perfect for Household & Utility Applications of Transferring Water from One place
to Another
WHAT'S IN THE BOX:
• (1) Water Pump
• (3) Power Adapters
TECHNICAL SPECS:
• Construction Material: Engineered ABS and Metal
• Power Output: AC 110V 60Hz
• Power Cord Length: 16 feet
• Type: Water Pump (blue)
• Diameter of Pipe: Screw thread in NPT1-1/4” & NPT5/8”. Flat PVC Hose in 0.98’’
and 1.26’’ inches
• Applications: Garden, Yard, Swimming pool, Pond, Flooded Area

Questions? Issues?
We are here to help!
Phone: [phone]
Email: suppor[email protected]