Serenity G1391 User manual

Wishing Well Water Feature Instruction Manual
G1391
Safety Warnings and General Information:
•Use this product only in accordance with the instructions.
•Children should be supervised to ensure that they do not play with product.
•This product is not a toy.
•Keep the product and its power cable out of reach of children.
•Before cleaning and when not in use unplug from the mains supply.
•Do not handle the electrical components with wet hands.
•Do not use the appliance with a damaged power cord or plug.
•To avoid hazards, ensure that any electric cable is safely out of the way of children and
pets.
•Where possible ensure all power cables are positioned away from footfall areas.
•It is important that an RCD (Residual Current Device) is present and any product of this
type is connected to it.
•When removing re-positioning or replacing the water pump make sure the power is off
and the plug is out of the socket.
•Repairs to electrical equipment should only be performed by a qualified electrician.
Improper repairs may place user at serious risk.
•Always use the original power cable supplied with the product.
•Make sure the voltage on the rating label matches the mains power supply to be used.
•Do not unplug by pulling the power cable.
•Water temperature must not exceed 35°C. Top the water levels up frequently during hot
weather.
•In very low temperatures, drain, dry and protect the water feature from frost, snow and
ice.
•This product is designed for outdoor use only and should not be positioned where water
spillage may damage carpets or furnishings.
•Always position on a flat level surface.
•The chosen location should be free from overhanging trees and bushes which may shed
their leaves in autumn.
•Ensure that the water level is always sufficient; do not allow the pump to run dry.
•To eliminate the possibility of water damage around your water feature, check for leaks
and excessive splashing after the initial setup.
•Do not leave your water feature running for extended periods of time unattended.
•Occasionally the water pump may make excessive noise, this may be due to the pump
rattling against the side of the reservoir or a small amount of trapped air. Always ensure
that the pump is suckered to the base using the rubber feet. Remove any trapped air by
gently shaking the water pump.
•This water feature is not suitable for commercial purposes.

Assembly Instructions:
1. Choose a flat, level surface for the assembly and the final location for your fountain.
2. Insert the water supply tube into the pump outlet. Place the pump upright in the basin and draw the
pump power cord out of the back of the fountain (see fig. 1).
3. Connect the female jack of the adaptor with male jack of the pump (see fig. 2).
4. Put the wheel on the notch of the two stumps located in the middle of the well (see fig. 3).
5. Add clean water into the basin so that the water level is approx. 30mm (1.18”) lower than the edge of
the basin (see fig. 4).
6. Plug the adaptor into an outlet. The fountain will begin to flow (see fig. 5).
Please note: the adaptor is rated IP44 and is suitable for outdoor use, but it is advisable to use
an indoor or waterproofed power outlet. The pump features a dial to increase or decrease the
water flow into the fountain.
7. To eliminate the possibility of water damage around your fountain, check for leaks and excessive
splashing after the initial setup of your fountain. It is highly recommended that this fountain is placed
in an area where it cannot be damaged.
8. Do not leave your fountain running for extended periods of time when no one is present to observe
the performance.
9. In times of snow and ice, fountains should be covered to protect them from the elements. Wrapping
these items for the winter is suggested. Prior to wrapping the item for winter, the item should be first
completely dry before covering and storing for winter otherwise it is subject to mold and possible
cracking. Wrap in a breathable material.
Care and Maintenance:
•Keep water clean and free from debris. If debris gets caught in the pump, disconnect it
from any power sources and rinse the pump under clean running water.
•Clean the water feature periodically to prevent build-up of mineral deposits on the sides
and base. Use a stiff brush and clean warm water with a little liquid soap. Do not use
detergents or abrasives as this will damage the surface of your water feature.
•Frost can cause damage to the pump. The pump must be removed and stored in a frost-
free environment if the water is likely to freeze.

GUARANTEE
IMPORTANT
Please do not return this product without first calling the Customer Service number below:
0871 911 7031*
Thank you for purchasing this product, which has been made to demanding high quality
standards and is guaranteed for domestic use against manufacturing faults for a period of 12
months from the date of purchase.
This guarantee does not affect your statutory rights. If your product fails due to a defect in material or
workmanship during this period, please return it to the place of purchase. Normal wear and tear is not
covered under the guarantee.
Any guarantee is invalid if the product has been misused or subject to neglect or an attempted repair
other than by our own service centre.
Due to continuous product improvement, we reserve the right to change the product specification
without prior notice.
After Sales Customer Service:
Customer Service Department, Branded Garden Products Ltd, Premier House, Hortonwood 7,
Telford, TF1 7GP, UK
Telephone: [phone]*
E-mail [email protected]
Please retain for future reference.
Colours and contents may vary.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Please note that all products with the symbol below must be recycled.
*Calls cost 13p per minute, plus your phone company’s access charge