Serialio Scanfob 2002 User manual

Visit http://serialio.com/support/Scanner/Scanfob_2002 for more information.
Setup for connecting Scanfob®2002 via Bluetooth as a Keyboard*
Using iPad, iPhone, iTouch? Use this page.
To use with SerialMagic or SerialMagic Gears, use the other side of this sheet.
Step 1: Connect Scanfob®2002 to powered USB port for about 4 hours
Watch iPad/iPhone video http://youtu.be/RGNDsYWBAyw
Step 2: Scan Keyboard-HID code to set the Scanfob®2002 to keyboard mode.
Keyboard - HID
Step 3: Scan the "Make Discoverable & Connectable" code below or press the small
button on the Scanfob®2002 for five seconds, and the LED will rapidly flash blue.
_+-DSCO-+_
Make Discoverable & Connectable
Step 4: Start Bluetooth discovery from the Phone/PC and pick the Scanfob ®scanner
when the "Scanfob..." name is shown on the Phone/PC.
Step 5: The Scanfob®2002 will begin beeping, the red scan beam will remain on, and the
phone/PC will display some numbers. Scan the number barcodes to the right in the order
presented by the phone or PC, then Scan the END barcode when done and the Scanfob®
2002 should beep, and the LED will slowly flash blue showing a good Bluetooth
connection. If a mistake is made scanning, scan End, and go back to Step 4.
Step 6: Scan one of the following codes as appropriate
iOS/Windows OS X
(prefix=NONE, suffix=CR) (prefix=NONE, suffix=ENTER)
Step 7 (optional): For iPad/iPhone/iPod Touch, scan “Enable iOS Keyboard Toggle”
below (only need to scan once). Press the small button on the Scanfob®2002 to toggle
the on-screen keyboard.
_+-IOSON-+_
Enable iOS Keyboard Toggle
When done using the Scanfob®2002 scan the "Disconnect and Radio Off" code below or hold the small button
for 5 seconds. To reconnect scan "Reconnect to Last Device" below or hold the big button for 5 seconds.
The following codes are handy for disconnecting and reconnecting the Scanfob 2002.
_+-DISC-+_ _+-CONN-+_
Disconnect and Radio Off Reconnect to Last Device
1 _Q1_
2 _Q2_
3 _Q3_
4 _Q4_
5 _Q5_
6 _Q6_
7 _Q7_
8 _Q8_
9 _Q9_
0 _Q0_
END _ZZ_

Visit http://serialio.com/support/Scanner/Scanfob_2002 for more information.
Setting up Scanfob®2002 via Bluetooth with SerialMagic*
Using iPad, iPhone, iTouch? Use other side of this sheet.
Step 1: Connect Scanfob®2002 to powered USB port for about 4 hours
Step 2: Scan the SerialMagic-SPP code below to setup the Scanfob®2002 for use
with SerialMagic.
SerialMagic - SPP
Step 3: Launch SerialMagic app and do setup per your platform.
Please find information at http://serialio.com/support/SerialMagic/index.php
Step 4: When SerialMagic app is looking for the Scanfob®2002 scan "Make Discoverable & Connectable" or
press the small button on the Scanfob®2002 for five seconds. The LED will flash blue rapidly.
_+-DSCO-+_
Make Discoverable & Connectable
Step 5: Pair the Scanfob®2002 with your Phone or PC using SerialMagic software (see SerialMagic
documentation for more information). The default Bluetooth PIN code for the Scanfob is 0000.
Step 6: Scan the following code (prefix=STX, suffix=CR)
Note: To reconnect the Scanfob®2002 to the Phone or PC after it has been setup, follow Step 2 above.
A slow blue flash of the LED shows a good Scanfob®2002 Bluetooth connection to your PC or Phone.
*SerialMagic software will post scans from the Scanfob®2002 to virtually any application on
your Android, BlackBerry, Windows Mobile, Symbian S60, Windows, & OS X.
If you did not purchase SerialMagic software with your Scanfob®2002, you can download a trial
version here: http://serialio.com/products/SerialMagic/SmSuppPlat.php
Scanfob 2002 Beep OFF Scanfob 2002 Beep ON
The following codes are handy for disconnecting and reconnecting the Scanfob 2002.
_+-DISC-+_ _+-DSCO-+_
Disconnect and Radio Off Reconnect SerialMagic
For additional beeper settings see the
URL at the bottom of this page