SerVision UVG400 User manual

UVG400
Installation Guide
September
2013

SerVision UVG400 Installation Guide
2
Trademarks & Copyright
Trademarks
All trademarks mentioned in this manual are the sole property of their respective manufacturers.
Copyright
SerVision Ltd., Jerusalem, Israel
www.servision.net • [e-mail]
© 2013 SerVision Ltd. All rights reserved.
Notice
Information in this document is subject to change without notice. SerVision Ltd. assumes no responsibility for any
errors that may appear in this manual. Companies, names and data used in examples herein are fictitious unless
otherwise noted. No part of this document may be copied or reproduced in any form, or by any means, electronic or
mechanical, for any purpose, without the express written permission of SerVision Ltd. SerVision Ltd. makes no
warranties with respect to this documentation and disclaims any implied warranties of merchantability or fitness for
a particular purpose.

SerVision UVG400 Installation Guide
3
Table of Contents
Introduction 4
The UVG400 Package 5
Additional Equipment 6
Installing the UVG400 System 7
Selecting a Location for the Unit 7
Diagram of the Rear Panel 7
Connecting Devices to the UVG400 10
Connecting Cameras 10
Connecting PTZ Controllers 10
Connecting Sensors 11
Connecting a Sensor Directly to the Unit 12
Connecting Sensors Using an ADAM Module 12
Connecting Activators 16
Connecting Sensors and Activators Using an IA Relay Board 16
Connecting Microphones 18
Connecting a Speaker or Headphones 18
Connecting a CCTV Monitor 19
Connecting the Mouse 20
Connecting a Switch 20
Connecting Multiple Monitors 20
Setting Up Network Connections 21
Connecting the UVG400 to an External Network 21
Connecting Devices to the UVG400’s Internal Network 21
Connecting the UVG400 to a Power Source 23

SerVision UVG400 Installation Guide
Introduction 4
Introduction
This guide explains how to set up the hardware components of SerVision’s UVG400 security system. The UVG400
belongs to SerVision’s line of embedded Video Gateway units. These units provide state-of-the-art security
functionality, including live video streaming, video recording and playback, motion detection, sensor management,
real-time event notification, and device activation. All of these features can be accessed remotely via PC, PDA, or
cellular telephone.
The UVG400 can stream video and other security data to users via cabled Ethernet connection or wirelessly via
WiFi or cellular networks. This versatility makes it ideal for securing locations in which cabled connections are not
available: garages, stables, parking lots, construction areas, etc.
Once the UVG400 has been installed as explained in this guide, it must be configured. Configuration is performed
by connecting to the UVG400 unit using a PC that is on the same network as the unit (or connected to the unit
directly using a LAN cross cable) and opening the unit’s configuration utility in a browser. For additional
information about configuring your UVG400, please refer to the Embedded Video Gateway System Guide.
Client software is used for accessing the UVG400 unit remotely in order to view video and events and control the
system in various ways. SerVision offers client software for PCs and for certain cellular telephone and PDA
models. Full instructions for the use of the client applications are available in separate manuals, which can be
downloaded at http://www.servision.net.

SerVision UVG400 Installation Guide
The UVG400 Package
The UVG400 package contains the following items:
Item Description Illustration
UVG400 unit Video Gateway
Power supply cable Connects the unit to an
electrical outlet
Ethernet (LAN) cable Connects the unit to a network
RS232/485 serial
adapter Connects PTZ controllers to the unit
Mouse Mouse for use with CCTV
monitors
The UVG400 Package 5

SerVision UVG400 Installation Guide
Additional Equipment 6
Additional Equipment
Up to four video cameras can be connected to the UVG400. You must acquire the cameras you require; they are not
included in the UVG400 package. For information about camera compatibility and about connecting the cameras to
the unit, see Connecting Cameras, page 10, or consult your vendor.
In addition to the cameras, you may wish to incorporate some or all of the optional equipment listed below into your
security system. For additional information about these items and the cables required to connect them, please refer
to the installation instructions for each type of device.
NOTE: This equipment is not included in the UVG400 package.
•Cellular modem with USB adaptor (see Connecting the UVG400 to an External Network, page 21)
Note: Not all cellular modems are supported. Please contact your UVG400 supplier or SerVision technical
support for a list of supported cellular modems.
•USB extension cord for connecting the cellular modem to the unit; the modem functions best if it is installed
as high up as possible and in an exposed location (see Connecting the UVG400 to an External Network,
page 21)
Note: The extension cord should not be longer than about 1.5 meters.
•WiFi card with USB adaptor (see Connecting the UVG400 to an External Network, page 21)
Note: Not all WiFi cards are supported. Please contact your UVG400 supplier or SerVision technical support
for a list of supported WiFi cards.
•Up to four dry-contact sensors (see Connecting Sensors, page 11)
Note: Up to four dry-contact sensors can be connected directly to the UVG400 unit. If you use either an
ADAM module or an IA relay board, as described below, you can connect an additional 16 dry-contact
sensors via the unit’s RS232/485 connector.
•ADAM Data Acquisition Module and ADAM isolated RS232->RS422/RS485 converter, for connecting up to
16 dry-contact sensors (see Connecting Sensors, page 11)
•Intelligent Appliance IA-3126-2 relay board, for connecting up to 16 dry-contact sensors (see Connecting
Sensors and Activators Using an IA Relay Board, page 16) and 16 activators to the UVG400 unit
•Up to two dry-contact activators (alarms or other devices that are turned on or off in response to the activation
of a sensor; see Connecting Activators, page 16)
Note: Up to two activators can be connected directly to the UVG400 unit. If you use an IA relay board, as
described above, you can connect an additional 16 activators via the unit’s RS232/485 connector.
•Up to two microphones (see Connecting Microphones, page 18)
•Speaker or headphones (the unit already contains a built-in speaker; see Connecting a Speaker or Headphones,
page 18)
•CCTV monitor for closed-circuit video display (see Connecting a CCTV Monitor, page 19)
•Push-button switch to change the display in a connected CCTV monitor (see Connecting a Switch, page 20)
•Toggle (on-off) switch to change the active outline (see Connecting Sensors, page 11)

SerVision UVG400 Installation Guide
Installing the UVG400 System 7
Installing the UVG400 System
These are the steps that you will typically follow in order to install the UVG400 system:
1. Place the UVG400 unit in its desired location; see Selecting a Location for the Unit, page 7.
2. Install the video cameras in their desired locations.
3. Install the sensors in their desired locations (optional).
Note: Four sensors can be connected directly to the unit; another 16 must be connected through an ADAM
module or an IA relay board; see Connecting Sensors, page 11.
4. Install a toggle switch to change the active outline (optional); see Connecting Sensors, page 11.
5. Install the activators in their desired locations (optional).
Note: Two activators can be connected directly to the unit; another 16 can be connected through an IA relay
board; see Connecting Activators, page 16.
6. Install a CCTV monitor in its desired location (optional).
Note: If you want to use a mouse to control the monitor display, place the monitor close to the UVG400 unit,
because the mouse is plugged into the unit, not into the monitor.
7. Install a push-button switch in its desired location (optional); the push-button switch can be used to change the
display on the CCTV monitor, if a monitor is connected to the unit; see Connecting Sensors, page 11.
8. Connect the cameras and other devices to the UVG400 and to a power supply, as required; see Connecting
Devices to the UVG400, page 10.
9. Place the cellular modem in an appropriate location in the vehicle and connect it to the unit using a USB
extension cord (optional); see Connecting the UVG400 to an External Network, page 21.
10. Connect the WiFi adaptor to the unit (optional); see Connecting the UVG400 to an External Network, page 21.
11. Connect the unit to a LAN using an Ethernet cable (optional); see Connecting the UVG400 to an External
Network, page 21.
12. Install any devices that will be connected to the UVG400's internal network in their desired locations. Connect
them to a power source and to the unit (optional); see Connecting Devices to the UVG400’s Internal Network,
page 21.
13. Connect the UVG400 unit to a power source; see Connecting the UVG400 to a Power Source, page 23.
Selecting a Location for the Unit
The UVG400 unit should be placed on a flat surface such as a table or shelf. (It is not designed for mounting
directly on a wall.) Ensure the unit has at least a few centimeters (1–2 inches) of space above it and on all sides for
ventilation.
When choosing a location for the UVG400, bear in mind that the unit must be connected to a power outlet and a
LAN or a PC, and that other devices (cameras, sensors, etc.) must be connected to it. Choose a location in which
these connections are feasible.
Diagram of the Rear Panel
The rear of the UVG400 unit contains the connectors and controls described below.

SerVision UVG400 Installation Guide
Reset
Powe
r
A
udio Out (Aout)
A
udio In2 (Ain2)
A
udio In1 (Ain1)
T
V Out
Ethernet
Cable
V
ideo In
V
in1–Vin4
Installing the UVG400 System 8
Figure 1: UVG400 connectors and controls
RS232/485
USB Ports
Mouse Connecto
r
Sensors
In1–In4
Activators
Out1, Out2
Ethernet In
Ethernet Out

SerVision UVG400 Installation Guide
Installing the UVG400 System 9
Connector/Control Description
Reset Reset button. Use a pin to press the button when it is necessary to reset the unit
manually.
Note: Your configuration settings will not be lost during a reset.
Power Connector for the power supply and, if required (see page 23)
Audio Out (Aout) Connector for an external speaker or headphones (see page 18)
Audio In2 (Ain2) Connector for an active microphone (see page 18)
Audio In1 (Ain1) Connector for a passive microphone (see page 18)
TV Out Connector for a CCTV monitor (see page 19)
Video In (Vin1–Vin4) Connectors for video cameras (see page 10)
Ethernet Cable Cable connecting the Video Gateway component of the UVG400 to the unit’s router.
Do not disconnect.
RS232/485 Serial (COM) port for PTZ controllers (see page 10), ADAM modules (see page 12),
or technicians' use
Mouse Connector Mouse connector (for the supplied PS2 mouse only; see page 19)
USB Ports Connectors for WiFi cards or cellular modems with USB adaptors (see page 21)
Sensors (In1 – In4) Sensor connectors (see page 11)
Ethernet Out 10/100 Base-T LAN connector for connecting the unit to an external network (LAN
or WAN; see page 21.)
Ethernet In Three 10/100 Base-T LAN connectors for connecting other devices to the internal
network managed by the UVG400’s router (see page 21)
Activators (Out1, Out2) Activator connectors (see page 16)

SerVision UVG400 Installation Guide
Connecting Devices to the UVG400
This section explains how to connect cameras, sensors, activators, microphones, a speaker or headphones, and a
CCTV monitor to the UVG400 unit.
Connecting Cameras
Up to four cameras can be connected to the UVG400. If the cameras have PTZ controls for remote aiming and
zooming, and the PTZ protocols they use are supported, the control cables can also be connected to the unit.
Any PAL or NTSC video camera with a composite video output can be connected to the unit. A cable with a
composite video connector on one end, and a male BNC connector on the other, should be used to connect each
camera to the UVG400.
NOTE: A cable with a male RCA connector can be connected to a female BNC connector by using an
RCA-to-BNC adaptor.
Figure 2: RCA-to-BNC adaptor
D To connect a camera:
1. Install the camera in its desired location.
2. Connect the output of the camera to one of the Video In connectors on the rear panel of the unit.
3. Connect the camera's power connector to a power source.
Connecting PTZ Controllers
If a camera has remote PTZ control features (pan, tilt, zoom, and/or focus), and uses a supported PTZ protocol, you
can connect the control cable to the unit. Both RS232 and RS485 PTZ connection types are supported. Consult the
camera documentation for information about which connection type to use.
NOTE: If you are connecting sensors to the unit using an ADAM module, you cannot connect any RS232 PTZ
controllers to the unit. For additional information, see Connecting Sensors Using an ADAM Module,
page 12.
If you want to connect the PTZ controllers of multiple cameras to the unit, only one of the controllers can use an
RS232 connector – the others must all use RS485 connectors. PTZ controllers for more than one RS232 camera
cannot be connected to the unit simultaneously.
If you connect multiple RS485 PTZ camera controllers, they should be daisy-chained to the RS232/485 connector,
as described below. In this case, each camera in the chain must be given a different ID number. Please refer to your
camera's documentation for information about configuring its ID number. In addition, note that you can only create
an RS485 daisy chain if every link on the chain (i.e., every camera) uses the same PTZ protocol. Attempting to
connect cameras that use different protocols will prevent all of the cameras from working properly.
Connecting Devices to the UVG400 10

SerVision UVG400 Installation Guide
D To connect an RS232 PTZ controller:
The RS232 controller cable should end with a female 9-pin RS232 connector.
•If you are only connecting the RS232 PTZ controller to the unit, and are not connecting any RS485 PTZ
controllers, plug the 9-pin RS232 connector directly into the RS232/485 connector on the rear panel of the
unit.
•If you are also connecting one or more RS485 PTZ controllers to the unit, plug the 9-pin RS232 connector into
the RS232/485 adapter supplied with the unit.
D To connect an RS485 PTZ controller:
Each RS485 controller cable should end with two wires.
1. Use a wire connector to connect the wires to the RS485 connection wires of the adapter. Be sure to match the
positive (+) wire of the controller cable to the positive (+ red) wire of the adapter, and the negative (-) wire of
the controller cable to the negative (- grey) wire of the adapter (see figure 3).
Figure 3: RS232/485 adapter
To connect multiple RS485 controllers to the adapter, insert the positive (+) wires of all of the controllers into
one slot in the wire connector, and the negative (-) wires of all of the controllers into the other slot of the wire
connector.
Figure 4: Wire connector
2. If multiple PTZ cameras are connected to the unit, configure each camera to use a different ID. For
information about how to do this, refer to the camera documentation.
3. Connect the RS232/485 adapter to the RS232/485 connector on the rear panel of the unit.
RS485 connection wires
Plug into RS232/485
connector on MVG 400UVG
RS232 connecto
r
Positive (+) wire for RS485
connector (red)
Negative (-) wire fo
r
RS485 connector (grey)
Connecting Sensors
Sensors are devices that detect events such as a door being opened or a light being turned on. Up to four dry-contact
input sensors can be connected directly to the unit. In addition, if you wish, you can connect either an ADAM Data
Connecting Devices to the UVG400 11

SerVision UVG400 Installation Guide
Acquisition Module or an IA-3126-2 relay board to the unit. Either of these devices makes it possible to connect up
to 16 additional sensors to the unit.
Sensor 1 and Sensor 4 can be used as switches instead of sensors. The switches can be used to activate outlines and
to change the display on a CCTV monitor.
Connecting a Sensor Directly to the Unit
The unit has four Input connectors (In1 – In4). You can use these connectors to connect up to four dry-contact
input sensors directly to the unit. Alternatively, In1 and In4 can be used to connect switches as follows:
•In1: If you are defining more than one outline (alternate sets of recording and event-handling settings), you
can connect a toggle (on-off) switch to In1 instead of a sensor. The switch can then be used to change the
active outline. For additional information, please refer to the Embedded Video Gateway System Guide.
Note: Some alarm panels can also be connected to In1. When they are, they can function as automatic outline
toggle switches. For additional information, please consult the alarm panel vendor.
•In4: If a CCTV monitor will be connected to the unit, you can connect a push-button switch to In4 instead of
a sensor. The button can then be used to change the display on the monitor. For additional information, see
Connecting a CCTV Monitor, page 19 and refer to the Embedded Video Gateway System Guide.
D To connect a sensor or switch directly to the unit:
1. Install the sensor or switch in its desired location in accordance with the manufacturer's instructions.
2. Connect the two wire contacts of the sensor or switch to the Sensors terminal block on the rear panel of the
UVG400, as illustrated in figure 5. Insert the wires into the connectors and tighten the screws below each
connector to hold the wires in place.
Note: The wires must be connected to two adjacent contacts in the same group (e.g. the two contacts of
“In1”), but the polarity does not matter.
Figure 5: Connecting a sensor
In1 In2 In3 In4
Sensor
Sensors terminal bloc
k
UVG rear panel
Connecting Sensors Using an ADAM Module
If you want to connect additional dry sensors to the UVG400, you can do so by connecting an ADAM Data
Acquisition Module to the unit. Up to 16 additional dry sensors can then be connected to the unit through the
ADAM module.
NOTE: Alternatively, you can connect additional sensors using an IA-3126-2 relay board, as explained
Connecting Sensors and Activators Using an IA Relay Board, page 16.
To connect sensors using an ADAM module, you will need the following items:
•ADAM-4051 Data Acquisition Module (available from SerVision)
•ADAM-4520 isolated RS232->RS422/RS485 converter (available from SerVision)
Connecting Devices to the UVG400 12

SerVision UVG400 Installation Guide
•Flat ribbon cable with D-type 9-pin female connector on one end and a D-type 9-pin male connector on the
other end
•Wire to connect the ADAM module to the ADAM converter – red, black, yellow, and green
•Wire and an electrical plug (optional) to connect the ADAM module to a power source
Figure 6: ADAM-4051 module
Figure 7: ADAM-4520 isolated converter
NOTE: The instructions below explain how to connect sensors to the UVG400 using the ADAM module and
converter described above. For additional information about connecting and configuring the ADAM
module and converter, please refer to the manufacturer's documentation, or contact your vendor.
D To connect sensors using an ADAM module:
1. Install the sensors in their desired locations in accordance with the manufacturer's instructions.
2. Connect the wire contacts of each of the sensors to the terminal blocks of the ADAM-4051 module as follows:
•
•
• Connect all of the negative (-) wires of all of the sensors to one of the ground (D GND) connectors on the
ADAM module. If the wires cannot all be inserted into the connector, use a wire connector to connect
them together, and then connect the wire connector to the ground (D GND) connector on the ADAM
module.
•
•
• Connect each of the positive (+) sensor wires to one of the numbered connectors (D1 0 through D1 15) in
the terminal blocks of the module.
Connecting Devices to the UVG400 13

SerVision UVG400 Installation Guide
Figure 8: Connecting sensors to the ADAM-4051 module
3. Connect the ADAM-4051 module to the ADAM-4520 isolated converter as follows (see figure 10, page 15):
D GN
D
Connect sensor ground
wires to this connector
D1 0 through D1 10
Connect positive (+) sensor wires
to these connectors
D1 11 through D1 15
Connect positive (+) sensor
wires to these connectors
D GN
D
Connect sensor ground
wires to this connector
Connect this connector on
the ADAM-4051 To this connector on the ADAM-4520
(Y) Data+ Data+
(G) Data- Data-
(R) +Vs (R)+Vs
(B) GND (B)GND
4. Connect the ADAM-4520 isolated converter to the RS232/485 connector on the rear panel of the UVG400
unit in one of the following ways:
•
•
• If you are not connecting any RS485 PTZ controllers to the unit, using the 9-pin flat ribbon cable, connect
the RS232 connector of the ADAM-4520 converter directly into the RS232/485 connector.
•
•
• If you are also connecting one or more RS485 PTZ controllers to the unit, using the 9-pin flat ribbon
cable, connect the RS232 connector of the ADAM-4520 converter into the RS232 connector of the
RS232/485 adapter supplied with the unit. Connect the PTZ controllers to the adaptor as explained under
Connecting PTZ Controllers, page 10. Then plug the adaptor into the RS232/485 connector on the unit.
Connecting Devices to the UVG400 14

SerVision UVG400 Installation Guide
Figure 9: RS232/485 adapter
Note: If you connect an ADAM module to the unit, you cannot connect any RS232 PTZ controllers or an IA
relay board to the unit. For additional information about connecting PTZ controllers to the unit, see
Connecting PTZ Controllers, page 10. For information about connecting an IA relay board to the unit, see
Connecting Sensors and Activators Using an IA Relay Board, page 16.
5. Connect the ADAM-4051 module to the power source as follows (see figure 10, page 15):
•
•
• Connect the positive (+) wire of the power supply cable to the (R) +Vs connector on the module
•
•
• Connect the negative (-) wire of the power supply cable to the (B) GND connector on the module
Note: Each of the power connectors on the module will then have two wires connected to it – one connecting
it to the power supply, and one connecting it to the power connectors of the ADAM-4520 converter.
Connect to RS232/485
connector on the UVG
(Y) Data +
(G) Data -
(R) +Vs
(B) GND
Connect to power
supply (-)
Connect to powe
r
supply (+)
Plug into RS232/485
connector on UVG
RS232 connector
Figure 10: Connecting the module to the converter, the UVG400, and the power supply
Connecting Devices to the UVG400 15

SerVision UVG400 Installation Guide
Connecting Activators
Activators are external devices such as alarms and lights that can be turned on by the system in response to an
event. Essentially, the unit functions as an on/off switch for these devices. The unit activates an activator by closing
the circuit of its power supply. Two activators can be connected directly to the unit. In addition, if you wish, you
can connect an IA-3126-2 relay board to the unit. This makes it possible to connect up to 16 additional activators to
the unit (see Connecting Sensors and Activators Using an IA Relay Board, page 16).
In addition to the activators themselves, you will need the 16 AWG red and black cables to connect each activator
to the unit.
D To connect an activator:
1. Install the activator in its desired location in accordance with the manufacturer's instructions.
2. Connect the two contacts of the activator to the Activators terminal block on the rear panel of the UVG400, as
illustrated in figure 11.
Note: The wires must be connected to two adjacent contacts in the same group (e.g. the two contacts of
“Out1”), but the polarity does not matter.
Figure 11: Connecting an activator that has its own power supply
Out1
Out2
MVG 400UVG
HV
G
r
e
a
r
pa
n
e
l
+ -
A
ctivator
s
terminal bloc
k
+ -
A
ctivato
r
+
Power
-
Connecting Sensors and Activators Using an IA Relay Board
If you want to connect additional dry sensors and/or two activators to the UVG400, you can do so by connecting an
Intelligent Appliance IA 3126-2 relay board to the unit. Up to 16 additional dry sensors and 16 additional activators
can then be connected to the unit through the relay board. Sensor and activator events from devices connected to an
IA relay board can be seen in SerVision client applications and activators can be turned on and off via these
applications. However, the sensors and activators cannot be configured using the UVG400’s configuration utility.
NOTE: Alternatively, you can connect additional sensors using an ADAM module, as explained under
Connecting Sensors Using an ADAM Module, page 12. Sensors that are connected through an ADAM
module can be configured using the UVG400’s configuration utility.
Connecting Devices to the UVG400 16

SerVision UVG400 Installation Guide
Figure 12: IA 3126-2 relay board
For information about connecting sensors and activators to the IA 3126-2 relay board, and about connecting the
relay board to a power source, please consult the relay-board’s documentation.
NOTE: If you are connecting less than 16 activators or 16 sensors to the relay board, be sure to connect them to
the relay beginning with the lowest connector, and do not leave open connectors between those that
you use. For example, if you are connecting 4 activators and 3 sensors, connect the activators to output
connectors 1-4 on the board and the sensors to input connectors 1-3 on the board.
D To connect the IA 3126-2 relay board to the UVG400:
1. Set the ID of the relay board to 0. (For information about how to do this, consult the relay-board
documentation.)
2. Connect the relay board to the RS232/485 connector on the rear panel of the UVG400 unit in one of the
following ways:
•
•
• If you are not connecting any RS485 PTZ controllers to the unit, using a 9-pin flat ribbon cable, connect
the RS232 connector of the relay board directly into the RS232/485 connector.
•
•
• If you are also connecting one or more RS485 PTZ controllers to the unit, using a 9-pin flat ribbon cable,
connect the RS232 connector of the relay board into the RS232 connector of the RS232/485 adapter
supplied with the unit. Connect the PTZ controllers to the adaptor as explained under Connecting PTZ
Controllers, page 10. Then plug the adaptor into the RS232/485 connector on the unit.
Connecting Devices to the UVG400 17

SerVision UVG400 Installation Guide
Figure 13: RS232/485 adapter
RS232 connector
Plug into RS232/485 serial port
connector on HVG 400
Note: If you connect a relay board to the unit, you cannot connect any RS232 PTZ controllers or an ADAM
module to the unit. For additional information about connecting PTZ controllers to the unit, see Connecting
PTZ Controllers, page 10. For information about connecting an ADAM module to the unit, see Connecting
Sensors Using an ADAM Module, page 12.
Connecting Microphones
Up to two microphones can be connected to the unit, one active and one passive. When one or two microphones are
connected, you can hear and record sound along with video images. The sound from a microphone can be
associated with any or all of the cameras. (For additional information, please refer to the Embedded Video Gateway
System Guide.)
Microphones can be connected to one or both of the Audio In connectors (Ain1 and/or Ain2). Passive
microphones, which require external amplification, must be connected to Ain1. Active (self-amplifying)
microphones must be connected to Ain2. Microphones with an output voltage of 1 Vrms or 1.41 Peak are
supported.
D To connect a microphone:
1. Install the microphone in the desired location.
2. Plug the microphone connector into the desired Audio In connector (Ain1 or Ain2).
Connecting a Speaker or Headphones
The UVG400 unit contains a built-in, 1-watt, internal speaker, which is located on the right side of the unit. You
can also connect an external speaker or headphones to the unit. The speakers (and headphones) allow you to hear
audio that is transmitted from one of the client applications. In addition, if you are viewing recorded video on a
CCTV monitor, these speakers can broadcast the audio associated with the video. The external speaker or
headphones can be used in addition to the internal speaker or instead of it. (For additional information, please refer
to the Embedded Video Gateway System Guide.)
Connecting Devices to the UVG400 18

SerVision UVG400 Installation Guide
Internal speaker
Figure 14: Internal speaker
D To connect a speaker or headphones:
1. Install the speaker in its desired location, if necessary.
2. Plug the speaker or headphone connector into the Audio Out (Aout) connector.
Connecting a CCTV Monitor
You can connect a CCTV monitor to the unit. The monitor offers an alternative way to view live or recorded video
from the UVG400. It is primarily useful if you want to view video when you are near the unit. For example, if the
UVG400 is set up in a grocery store, and you sit at the check-out counter, you can use a CCTV monitor to keep tabs
on parts of the store that you cannot see from your seat.
The following types of monitors can be used:
•Surveillance monitors: Monitors that are designed to be plugged directly into surveillance cameras.
•Entertainment monitors: Monitors that are intended to be plugged into portable DVD players in vehicles.
•Standard television sets with AV connectors
When choosing a monitor to connect to the unit, ensure the monitor supports the video format used by the cameras
(NTSC or PAL). Some SECAM monitors will also work when the PAL video format is used.
To connect the monitor to the UVG400, you will need a cable with the following connectors:
•An appropriate connector (BNC or RCA) for the Video In connector of the monitor. (Consult the monitor
documentation or your vendor to find out which kind of connector is required for the particular monitor you
are using.)
•A BNC male connector to connect to the TV Out connector of the UVG400. (A cable with an RCA connector
can be used by attaching a BNC-to-RCA adaptor to the connector. See figure 9, page 10.)
D To connect a CCTV monitor:
1. Install the monitor in its desired location.
2. Connect the Video In connector of the monitor to the TV Out connector of the UVG400, using a cable with an
appropriate connector (BNC or RCA) for the Video In connector of the monitor on one end, and a BNC male
connector on the other end.
Note: If you are using a standard television set as a monitor, use the television’s AV connector as the Video
Input connector.
Connecting Devices to the UVG400 19

SerVision UVG400 Installation Guide
Connecting Devices to the UVG400 20
Connecting the Mouse
If you wish, you can also connect the supplied mouse to the UVG400 when the video monitor is connected. When
the mouse is connected, you can use it to control the screen display, select cameras, play recorded video, and
activate PTZ controls (if available). For additional information, please refer to the Embedded Video Gateway
System Guide.
NOTE: Only the mouse supplied with the UVG400 is supported. If you connect a different mouse, the mouse
may be damaged.
D To connect the mouse:
•Plug the mouse into the Mouse Connector on the rear panel of the unit.
Connecting a Switch
If you wish, you can connect a switch to the unit to change the display on the monitor. The switch must be
connected to the Sensor 4 (In4) connector. For additional information, see Connecting Sensors, page 11 and refer to
the Embedded Video Gateway System Guide.
Connecting Multiple Monitors
If you wish, you can connect multiple CCTV monitors to the UVG400. For example, you may wish to have one
monitor beside a check-out counter, and another in the manager's office.
To connect multiple monitors, you must use video splitters to split the connection. Bear in mind, however, that the
image quality in each of the monitors will be slightly degraded. To correct this problem, you can use a video
amplifier (booster) for each monitor. To ensure you have the correct equipment, consult a video equipment supplier.
Note, also, that only one mouse can be connected to the unit. This means that there is only one point of control over
the display, and the display will be identical on all connected monitors.