Sesamsec Secustos sq80 series User manual

SECUSTOS SQ80 SERIES

Multi-frequency access control readers

USER MANUAL

TABLE OF CONTENTS

1INTRODUCTION............................................................................................................................................................ 3

1.1 ABOUT THIS MANUAL ..........................................................................................................................................3

1.2 SCOPE OF DELIVERY ..........................................................................................................................................3

1.2.1 COMPONENTS ..............................................................................................................................................3

1.2.2 ACCESSORIES ..............................................................................................................................................4

1.3 SESAMSEC SUPPORT .........................................................................................................................................4

2INTENDED USE............................................................................................................................................................. 5

3SAFETY INFORMATION ............................................................................................................................................ 6

4TECHNICAL DATA ....................................................................................................................................................... 9

4.1 TECHNICAL SPECIFICATIONS .........................................................................................................................9

4.2 FIRMWARE ................................................................................................................................................................9

4.3 ANTENNAS ..............................................................................................................................................................10

5INSTALLATION ............................................................................................................................................................ 11

5.1 GETTING STARTED.............................................................................................................................................11

5.2 INSTALLATION OVERVIEW ..............................................................................................................................12

5.3 ELECTRICAL CONNECTION ............................................................................................................................13

5.3.1 CONNECTOR ASSIGNMENT .................................................................................................................13

5.3.2 ADDITIONAL CABLE INFORMATION..................................................................................................13

5.4 MECHANICAL INSTALLATION.........................................................................................................................14

5.4.1 INSTALLATION DIRECTLY ON THE WALL.......................................................................................14

5.4.2 INSTALLATION WIT FLUSH-MOUNTED BOX..................................................................................15

6SETTINGS ..................................................................................................................................................................... 16

6.1 GENERAL SETTINGS..........................................................................................................................................16

6.2 CONFIGURATION WITH SECUSTOS SECO APP....................................................................................16

6.3 CONFIGURATION WITH USB CABLE...........................................................................................................16

6.4 CONNECTION TO AN ACCESS CONTROLLER .......................................................................................17

6.4.1 LINE TOPOLOGY ........................................................................................................................................17

6.4.2 STAR TOPOLOGY ......................................................................................................................................17

7COMPLIANCE STATEMENTS................................................................................................................................ 19

7.1 EU................................................................................................................................................................................19

7.2 RF EXPOSURE COMPLIANCE ........................................................................................................................19

7.3 UNITED KINGDOM ...............................................................................................................................................19

APPENDIX.................................................................................................................................................................................. 20

A – RELEVANT DOCUMENTATION............................................................................................................................20

B – TERMS AND ABBREVIATIONS ............................................................................................................................20

C – REVISION HISTORY.................................................................................................................................................21

1 INTRODUCTION

1.1 ABOUT THIS MANUAL

This manual is intended for users and installers. It enables a safe and appropriate handling of the product and

it gives a general overview, as well as important technical data and safety information about the product. Before

installing and using the product, the users and installers should read and understand the content of this manual.

For the sake of better understanding and readability, this manual might contain exemplary pictures, drawings

and other illustrations. Depending on your product configuration, these pictures might differ from the actual

design of your product.

The original version of this manual has been written in English. Wherever the manual is available in another

language, it is considered as a translation of the original document for information purposes only. In case of

discrepancy, the original version in English will prevail.

1.2 SCOPE OF DELIVERY

1.2.1 COMPONENTS

Your Secustos SQ80 access control reader is delivered as a kit with the following components:

Secustos SQ80 reader

All Secustos SQ80 readers are equipped ex-works

with one 4-pin (X1) and one 6-pin (X2) connector.

Depending on the product configuration, access

control readers of the Secustos SQ80 series are

available with or without keypad, in a silver or gray

housing.

4-pin connector (X1)

6-pin connector (X2)

Mounting plate

The mounting plate delivered with the kit enables to

fix the Secustos SQ80 reader on a wall.

It must be fixed directly to the wall or on a flush-

mounted box with 2 to 4 screws*

*Not part of the delivery

(screws are generally

available on site)

Fixing screw

(countersunk screw with

cross recess, M2x5)

The fixing screw delivered with the kit is intended to

fix the Secustos SQ80 reader on the mounting plate.

Due to its small size and inconspicuousness,

particular attention should be given to the screw

when unpacking the kit, as the screw might easily fall

down from the support and get lost.

Installation guide

(exemplary illustration)

The installation guide

delivered with the product

gives a short description of the installation options.

Please note that the installation guide does not

replace the user manual!

1.2.2 ACCESSORIES

Depending on your product configuration, the product can be delivered with the following accessories:

Mounting frame

Additional frame required for on-wall installation.

The mounting frame is delivered with 4 fixing screws

and 2 rubber seals on each side of the frame.

Part no.:

T4SA-QWF1SL (mounting frame, silver)

T4SA-QWF1GY (mounting frame, gray)

USB maintenance and

configuration cable

Specific USB cable intended for maintenance and

configuration purposes only.

Particular attention should be given when plugging

the USB cable in and out of the Secustos SQ80

reader.

Part no.: CAB-J4MSBAMSB150

1.3 SESAMSEC SUPPORT

In case of any technical questions, refer to the sesamsec website (www.seamsec.com) or contact sesamsec

technical support at

support@sesamsec.com

In case of questions regarding your product order, contact your Sales representative or sesamsec customer

service at

info@sesamsec.com

2 INTENDED USE

Secustos SQ80 is a product family of access control readers based on RFID technology. The readers give the

user the possibility to read simultaneously more than 60 RFID technologies from low (125 kHz) and high

(13.56 MHz) frequency bands. Many mobile use cases can be facilitated with their NFC and, optionally, BLE

functions, like authentication and data communication.

All readers are for both indoor and outdoor use in environmental conditions according to the respective product

data sheets and installation instructions given in this manual.

Any use other than the intended use described in this section, as well as any failure to comply with

the safety information given in this document, is considered improper use. sesamsec excludes any

liability in case of improper use or faulty product installation.

3 SAFETY INFORMATION

Transport and storage

•Observe carefully the transport and storage conditions described on the product packaging or other relevant

product documents (e.g. data sheet).

Unpacking and installation

•Before unpacking and installing the product, this user manual and all relevant installation instructions must

be read carefully and understood.

•After unpacking the product, check that all components have been delivered according to your order and

delivery note.

Contact sesamsec if your kit is not complete.

•The following measures must be checked prior to any product installation:

oMake sure that the mounting location and tools used for the installation are appropriate and safe.

In addition, make sure that the cables intended to be used for the installation are appropriate. Refer

to Chapter “Installation” for more information.

oIn case the product is installed outside, check if any further installation steps are required (e.g.

sealing of cables or housing). Refer to Chapter “Installation” for more information.

oThe product is an electrical device made of sensitive materials (e.g. glass housing). Check all

product components and accessories for any damage.

A damaged product or component may not be used for the installation.

oLife-threatening hazard in the event of fire

A faulty or improper installation of the product might cause a fire and lead to death or severe

injuries.

Check that the mounting location is equipped with appropriate safety installations and devices, like

a smoke alarm or fire extinguisher.

oLife-threatening hazard due to electrical shock

Make sure that there is no voltage on the wires before starting with the electrical wiring of the

product and check that power is turned off by testing the power supply of each wire.

Power to the reader supply should be applied only after the installation has been completed.

oMake sure that the product is installed in accordance with local electrical standards and regulations

and observe general safety measures.

oRisk of property damage due to transient overvoltages (surges)

Transient overvoltages imply short-duration voltage peaks that might result in system breakdown

or significant damages of electrical installations and devices.

sesamsec recommends the installation of appropriate Surge Protection Devices (SPD) by a

qualified and authorized personnel.

osesamsec also recommends the installers to follow general ESD protective measures during the

installation of the product.

Please also refer to the safety information in Chapter “Installation”.

•The product might show sharp edges or corners and requires a particular attention during the unpacking

and installation.

Unpack the product carefully and do not touch any sharp edges or corners, or any sensitive

components on the product. If necessary, wear safety gloves.

•In case the product is equipped with a cable, do not twist or pull the cable.

•In case of an on-wall or in-wall installation, the product must be installed in conformity with applicable local

regulations.

Observe the minimum installation height and other regulations applicable in the region in which

the product is installed.

•The product is an electronic product whose installation requires specific skills and expertise.

The installation of the product should be done by a trained and qualified personnel only.

Handling

•Depending on your product configuration, the product might be equipped with one or more light-emitting

diodes (LED).

Avoid direct eye contact with the blinking or steady light of the light-emitting diodes.

•The product has been designed for a use under specific conditions, e.g. in a specific temperature range

(refer to the product data sheet).

Any use of the product under different conditions might damage the product or alter its reading performance.

•The use of other RFID readers or reader modules in direct vicinity to the product, or in combination with the

product might damage the product or alter its reading performance. In case of doubts, contact sesamsec

for more information.

•The user is liable for the use of spare parts or accessories other than the ones sold or recommended by

sesamsec.

sesamsec excludes any liability for damages or injuries resulting from the use of spare parts or accessories

other than the ones sold or recommended by sesamsec.

•In case the product is equipped with a cable, the cable may not be replaced or extended.

sesamsec excludes any liability for damages or injuries resulting from a use of the product with a cable

extension or a replaced cable.

•Like most electronic devices, RFID systems generate electromagnetic waves that can vary in amplitude

and frequency. It is generally known and accepted that some RFID devices might potentially interfere with

personal medical devices, like pacemakers or hearing aids.

The access control readers of the Secustos SQ80 series fulfill general radio and EMC requirements.

However, users with a pacemaker or any other medical device should use the Secustos SQ80

readers carefully and refer to the information given by the manufacturer of their medical devices

before using the readers.

Maintenance and cleaning

•Any repair or maintenance work should be done by a trained and qualified personnel only.

Do not allow any repair or maintenance work on the product by an unqualified or unauthorized third

party.

•Life-threatening hazard due to electrical shock

Before any repair or maintenance work, turn the power off.

•Check the installation and electrical connection of the product in regular intervals for any signs of damage

or wear. Should any damage or wear be noticed, contact sesamsec or a trained and qualified personnel for

repair or maintenance work.

•The product does not need any special cleaning. However, the housing may be carefully cleaned up with

a soft, dry cloth and a non-aggressive or non-halogenated cleaning agent on the outer surface only.

Make sure that the used cloth and cleaning agent do not damage the product or its components

(e.g. label(s)).

Disposal

•The product must be disposed of in accordance with the EU directive on waste electrical and electronic

equipment (WEEE) or any applicable local regulations.

Product modifications

•The product has been designed, manufactured and certified as defined by sesamsec.

Any product modification without prior written approval from sesamsec is prohibited and

considered improper use of the product. Unauthorized product modifications may also result in the

loss of product certifications.

If you are unsure about any part of the safety information above, contact sesamsec support.

Any failure to comply with the safety information given in this document is considered improper use.

sesamsec excludes any liability in case of improper use or faulty product installation.

4 TECHNICAL DATA

4.1 TECHNICAL SPECIFICATIONS

Secustos

SQ80

Secustos

SQ80 K

Secustos

SQ80 K LEGIC

Secustos

SQ80 K LF HF

Secustos

SQ80 LEGIC

Secustos

SQ80 LF HF

transponders ●●●●●●

NFC ●●●●●●

BLE ●●●●

Keypad ●●●

Dimensions

(L x W x H)

Reader frame only (mounted): approx. 86 x 86 x 8.25 mm / 3.38 x 3.38 x 0.33 inch

Rear connector height: approx. 8 mm / 0.31 inch

Reader with rear connector: approx. 86 x 86 x 15.9 mm / 3.38 x 3.38 x 0.62 inch

Optional mounting frame: approx. 86 x 86 x 9.75 mm / 3.38 x 3.38 x 0.38 inch

Weight

Reader, potted, with connectors

and mounting plate: approx. 113 g / 3.99 oz

Power

6.0 V - 28 V via connector X1

PS2 classified power source according to IEC 62368-1, short-circuit current < 8 A

Current

consumption Max. 300 mA @ 6.0 V

Temperature

range

Operating: -20 °C up to +60 °C (-4 °F up to +140 °F)

Storage: -20 °C up to +70 °C (-4 °F up to +158 °F)

Relative

Humidity

Mounted front: IP65 protected housing

Transport/Storage: 5% to 95% non-condensing

4.2 FIRMWARE

Your product is delivered ex-works with a specific firmware version. Refer to the label attached to the product

to find the firmware version installed ex-works.

A/B1.50/NCD4.70/STD2.02/B/BT1.07EL

(exemplary firmware)

4.3 ANTENNAS

The readers contain an RFID reader module equipped with the following antennas:

HF antenna

(13.56 MHz)

LF antenna

(125 kHz)

BLE

(2.4 GHz)*

Secustos SQ80

Dimensions:

approx. 42 x 25 mm

(1.65 x 0.98 inch)

Number of turns: 4

Outer diameter:

max. 16.3 mm

(0.64 inch)

Number of turns: 144

Integrated BLE module

Secustos SQ80 K

Integrated BLE module

Secustos SQ80 K

LEGIC Integrated BLE module

Secustos SQ80 K

LF HF n/a

Secustos SQ80

LEGIC Integrated BLE module

Secustos SQ80

LF HF n/a

*Optional (Secustos SQ80 K LF HF and Secustos SQ80 LF HF do not support BLE)

For more information, refer to the respective product data sheets or other technical documents.

5 INSTALLATION

5.1 GETTING STARTED

Before starting with the installation of a Secustos reader, the following measures must be checked:

•Make sure you have read and understood all safety information given in Chapter “Safety information”.

•Make sure that there is no voltage on the wires and check that power is turned off by testing the power

supply of each wire.

•Make sure that all tools and components required for the installation are available and appropriate.

•Make sure that the installation site is appropriate for the installation of the reader. In particular, check

that the temperature of the installation site is within the operating temperature range given in the

Secustos technical documentation and make sure that the wall used for the installation is appropriate. In

some cases, the wall material might not be suitable for a safe and durable installation, or it might require

specific mounting screws (e.g. wall made out of silicon or drywall). Furthermore, some materials might

interfere with the RFID antennas of the reader and reduce its reading performance (e.g. metallic

surfaces). Contact sesamsec for more information.

•The recommended installation height for a standard installation is 110 cm from the ground. However, in

some cases (e.g. wheelchair access, local regulations, etc.), the actual installation height on site might

differ from the recommended height. Please also note the maximum wall mounting height of 200 cm

from the ground.

•In case of power lines, make sure that the minimum distance between the connection cable of the

reader and the next power line is 10 cm.

•In case other RFID devices are already installed on site, or if several Secustos readers must be

installed on the same site, observe a minimum distance of 30 cm between all readers and devices in

order to achieve the best reading performance for each reader. Should two readers be installed in the

same location (e.g. on each side of a wall, next to a door), the wall thickness should also be at least 30

cm to prevent a loss of performance of both readers.

Example 1:

installation of 2 readers next to each other

Example 2:

installation of 2 readers on each side of a wall (i.e. inside/outside)

•When installing the reader, do not cover the top left corner of the RFID module (i.e. top right corner

when the reader is fixed on the wall), as it would disable both proximity and ambient light sensors.

proximity and ambient light sensors (blue frame)

front view

•The protective film on the housing front should only be removed after complete installation of the reader.

5.2 INSTALLATION OVERVIEW

The illustration below gives an overview on an exemplary installation of a Secustos SQ80 access control

reader:

5.3 ELECTRICAL CONNECTION

5.3.1 CONNECTOR ASSIGNMENT

Drawing – RFID module contained in Secustos SQ80 readers

Power supply

V+

Input voltage 6 – 28 V

V-

Ground

Data transfer

A+

RS-485, cable length: max. 1000 m

B-

RS-485, cable length: max. 1000 m

Wiegand D0, cable length: max 200 m*

IN1

Digital input 1, cable length: max 200 m*

IN2

Digital input 2, cable length: max 200 m*

IN3

Digital input 3, cable length: max 200 m*

INS

Digital input S (for external Sabotage

switch), optional if sabotage button is

not available on the reader, cable

length: max 200 m*

* Cable routing requirements: twisted pair cabling (D0/GND,

D1/GND).

Maintenance / Configuration

USB

4-pin USB connector, 1.25 mm pitch (for

maintenance and configuration

purposes only)

5.3.2 ADDITIONAL CABLE INFORMATION

Typical installation cables are:

JY(ST)Y 4x2x0.6 for distance between devices ≤ 25 m

JY(ST)Y 4x2x0.8 for distance between devices > 25 m

Alternatively, any other appropriate cables that meet the prerequisites of RS-485 installations and wirings can

be used.

In case of long cables, voltage drops might lead to a breakdown of the readers. To prevent such malfunctions,

it is recommended to wire the ground (V-) and input voltage (V+) with two wires each.

In addition, the installation cable used to connect the controller must contain a cable shield and/or a drain

wire with PE connection.

The cable shield/drain wire may not be connected to the reader, but only to the controller. Otherwise, it could

lead to a potential difference.

5.4 MECHANICAL INSTALLATION

5.4.1 INSTALLATION DIRECTLY ON THE WALL

1. Fix the mounting frame to the wall as described below:

2. The mounting frame is equipped with a cable inlet on its bottom side, which also serves as a

cable strain relief. Optionally, the cable inlet can be sealed with silicone.

3. Finally, attach the mounting plate to the mounting frame, and the reader to the mounting plate

as described below:

Rubber seal

Mounting screws

Connection cable

Mounting frame

Rubber seal

Sealant

Cable inlet

Mounting frame

Mounting plate

Fixing screws for

mounting plate

Fixing screw for

reader

Reader

5.4.2 INSTALLATION WIT FLUSH-MOUNTED BOX

1. Attach the mounting plate to the flush-mounted box, and the reader to the mounting plate as

described below:

Connection cable

Flush-mounted box

Mounting plate

Fixing screw for

reader

Reader

6 SETTINGS

6.1 GENERAL SETTINGS

By default, the reader is delivered ex-works with the following settings:

•OSDP: 9600 baud

•Address: 0

•Terminating resistors: off

A customer-specific configuration is also possible by changing the device settings with the sesamsec Seconfig

tool.

6.2 CONFIGURATION WITH SECUSTOS SECO APP

The reader configuration with the Secustos Seco app requires an NFC-enabled mobile device (e.g.

smartphone or tablet) with Android operating system (from Android 4.0). The Seco app must be downloaded

from the Google Play Store and installed on the mobile device. Once the app has been installed, it is possible

to set parameters on the mobile device and transmit them subsequently on the reader via NFC.

6.3 CONFIGURATION WITH USB CABLE

The reader can also be configured using the sesamsec specific USB cable (refer to Chapter “Accessories”)

and the sesamsec Seconfig tool.

To do so, proceed as follows:

1. Connect the reader to a PC with the USB cable.

Particular attention should be given when plugging the USB cable in and out of the reader, as

the 4-pin USB connector is a very sensitive component.

Do not twist or pull excessively on the reader and press the connector lock when plugging

the cable out.

2. Open the Seconfig tool on the PC and set the reader as requested.

Refer to the Secustos technical handbook for more information about the reader settings.

3. Save your settings before closing the Seconfig tool and disconnect the reader from the PC by plugging

out the USB cable carefully.

6.4 CONNECTION TO AN ACCESS CONTROLLER

6.4.1 LINE TOPOLOGY

In this configuration, the reader bus consists of one reader connected to an RS-485 controller bus. An address

must be assigned to the reader and the terminating resistors of the RS-485 bus on the reader and on the

controller must also be set.

Reader

Address: 0

Terminating resistor: on

Controller

Terminating resistor: on

6.4.2 STAR TOPOLOGY

In this configuration, the reader bus consists of max. two readers, which are both connected to the same RS-

485 controller bus. An address must be assigned to each reader before initial operation (e.g. Reader 1 =

Address 0, Reader 2 = Address 1) as two readers with the same address would cause a conflict.

The terminating resistors of the RS-485 bus on both readers must be on, whereas the terminating resistor of

the RS-485 bus on the controller must be off.

The terminating resistors of the RS-485 bus on the readers and on the controller must also be set.

Controller

Terminating resistor: off

Reader 1

Address: 0

Terminating resistor: on

Reader 2

Address: 1

Terminating resistor: on

Please note:

•A star topology is only possible with max. two readers.

•In general, the terminating resistors of the devices opening and closing the RS-485 bus must be on. The

terminating resistors of all other devices within the RS-485 bus are off.

•An RS-485 bus should contain max. two readers. Operating more than two readers would lead to a

performance loss.

•A correct configuration of the controller is necessary to ensure a proper function of the readers.

7 COMPLIANCE STATEMENTS

7.1 EU

Hereby, sesamsec GmbH declares that the following products are in compliance with Directive 2014/53/EU:

•Secustos SQ80 K LEGIC

•Secustos SQ80 LEGIC

The full text of the respective EU declarations of conformity is available at the following internet address:

sesamsec.me/approvals

7.2 RF EXPOSURE COMPLIANCE

RF exposure statement (mobile and fixed devices)

This device complies with the RF exposure requirements for mobile and fixed devices. However, the device

shall be used in such a manner that the potential for human contact during normal operation is minimized.

7.3 UNITED KINGDOM

The following products comply with the requirements of the UK legislations and other regulations as listed in

the respective UK declarations of conformity.

•Secustos SQ80 K LEGIC

•Secustos SQ80 LEGIC

The importer is responsible for applying the following information to the packaging of the products:

•the importer company’s details, including the company’s name and a contact address

in the United Kingdom.

•UKCA marking

This manual suits for next models

Table of contents

Popular IP Access Controllers manuals by other brands

urmet domus

urmet domus 1099/811 quick guide

suprema

suprema CoreStation CS-40 Configuration guide

BioMax

BioMax N-WL20 manual

KEYKING

KEYKING FPC3002Q user manual

EDEN INNOVATIONS

EDEN INNOVATIONS OPTIMA BOX+ Techical manual

RF SOLUTIONS

RF SOLUTIONS FlexiPanel BlueLock manual

Owon

Owon SAC451 quick start guide

Videx

Videx PORTAL PLUS Application note

LeeLen

LeeLen 8 Series installation manual

Continental Access

Continental Access CARDACCESS 3000 - ARCHITECTURAL AND ENGINEERING SPECIFICATION... specification

Belco Security

Belco Security DA3000 user manual

Grosvenor

Grosvenor Janus C4 485 installation guide

TimeTec

TimeTec AC1 Series user guide

Paxton

Paxton ins-20100 quick start guide

Accuride

Accuride SENSEON PLUS installation guide

eKey

eKey FS WM 2.0 Mounting instruction

CEBEK

CEBEK DA-03 manual

HIK VISION

HIK VISION DS-K1T6QT-F43 Series user manual

sesamsec SECUSTOS SQ80 Series User manual

Popular IP Access Controllers manuals by other brands