Prastel M2000pe User manual

M2000PE ENGLISH ISM2000PEEU_02_05.doc

1. GENERAL DESCRIPTION

M2000PE is an access control unit for the operation of two doors.

It is equipped with an integrated 433MHz radio receiver, two inputs for external readers, two output relays with 5A-capacity contacts for direct

connection to the electric locks, and an internal memory with a storage capacity of 2000 user codes.

It is also fitted with 4 keys and a 4-digit display for code and functional parameter setting, and more precisely for

•programming new codes into the memory (through self-learning via the radio or the readers connected to the inputs);

•deleting single codes from the memory;

•selecting either bistable or timed operation mode independently for each relay;

•setting activation time for each relay (in the timed operation mode);

•associating any of the four channels of the radio transmitters to each relay;

•activating transfer of set data to another M2000PE unit connected via the RS485 serial line.

All operations can also be performed through the remote M/KEYB keyboard/display connected to the unit via RS/485.

All M2000PE circuits and components are housed in a plastic enclosure suitable for indoor installation and for mounting on bars according to DIN

standards. The M/KEYB keyboard is housed in an enclosure for wall-mounting or for countertop use.

2. TECHNICAL FEATURES

Power supply 12-24Vac/dc

Inputs integrated 433.92MHz radio receiver, 4 channels + 2 inputs with Wiegand protocol

Memory capacity 2,000 users

No. of output relays 2, controlled by two Wiegand inputs and/or by radio input, with the possibility of selecting channel address for each

relay. Example: channel 4 transmitter on relay 2.

Contact for enabling reading function on the door (one for each relay).

Inputs for forcing activation of the single door (“door opener” push-button)

Relay operating mode timed from 1 to 180 seconds

Relay contact capacity 5 A

Programming 4 keys (FUN, INC, DEC, VAL) and 4 displays plus M/KEYB remote optional keyboard/display

Other functions RS/485 serial communication port for transferring data to a slave unit and for connection of the M/KEYB remote

keyboard with 4 keys and 4 displays

Dimensions and weight 105x90x60, 320 grams

3. FUNCTIONS

Programming new codes

1. Simultaneously press keys INC and DEC.

2. Select a free storage location via keys INC and DEC (free location is indicated by decimal points being off).

3. Perform transmission or have the badge to be stored read by the badge reader (decimal points will go on).

4. Confirm by pressing key VAL (decimal points will briefly flash).

5. Repeat procedure from step 2 to enter other codes or simultaneously press keys INC and DEC to exit from programming mode.

Deleting codes

1. Simultaneously press keys INC and DEC.

2. Select the storage location to be deleted via keys INC and DEC (decimal points on indicate that the location is engaged)

3. Press the VAL key. The letter -C- will now appear on the left-hand side of the display.

4. Press the VAL key again to confirm deletion. The decimal points will go off and the storage location ‘h’ will be deleted.

5. Repeat procedure from step 2 to delete other codes and simultaneously press keys INC and DEC to exit from the programming mode.

Selecting operation mode and relay timing

1. Simultaneously press keys INC and DEC.

2. Press key FUN to access the function selection menu.

3. Select function F1 (relay 1) or F2 (relay 2) by pressing keys INC and DEC.

4. Confirm selection by pressing the VAL key; current parameter value will appear on the display.

5. Select the value to be assigned to the parameter by pressing keys INC and DEC. If value 0000 is set, the relay will operate in the bistable mode.

If a value between 1 and 180 is selected, the relay will operate in the monostable mode with activation time corresponding to the set value

(expressed in seconds).

6. Confirm by pressing key VAL; display will return to function selection and the new parameter will be stored.

7. Simultaneously press keys INC and DEC to exit from programming mode.

Assigning radio channel to the relay

1. Simultaneously press keys INC and DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F3 (relay 1) or F4 (relay 2) by pressing keys INC and DEC.

4. Confirm selection by pressing the VAL key; current parameter value will appear on the display.

5. Select the desired radio transmitter channel (1, 2, 3 or 4) to be assigned to the relay by pressing keys INC and DEC.

6. Confirm by pressing key VAL; display will return to function selection and the new parameter will be stored.

7. Simultaneously press keys INC and DEC to exit from programming mode.

Entering the password

1. Access programming mode by pressing keys INC + DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F5 by pressing keys INC and DEC and confirm by pressing the VAL key.

4. The letter P will appear on the left side of the display. Digit a sequence of six keys within 10 seconds. Each time a key is pressed, the letter P will

flash.

5. Upon the full sequence of six keys having been completed, the function selection menu will reappear on the display.

Failure to complete sequence within 10 seconds will abort password entry. This also avoids entry of incorrect passwords in case of any doubts as to

the sequence to be entered or erroneous pressing of any key.

M2000PE ENGLISH ISM2000PEEU_02_05.doc

The password is stored in EEPROM and is requested whenever INC+DEC are pressed to access programming mode starting from the stand-by

status (displays being off). In this case:

1. The letter P appears on the left side of the display. Digit the sequence of six keys corresponding to the password. Each time a key is pressed, the

letter P will flash.

2. Upon the 6-key sequence being completed, programming mode is accessed. If sequence is erroneous, the displays will go off.

Upon programming mode being accessed, any resident password may be deleted or replaced with a new one.

Note: To remove a password which has been forgotten, contact system supplier.

Deleting a resident password

1. Press INC+DEC to access programming mode: the password will be requested.

2. Digit in the password.

3. Press the FUN key to access the function selection menu.

4. Select the password entry function F5 by pressing keys INC and DEC and confirm by pressing key VAL.

5. Allow time-out (10 seconds) to elapse; password is deleted and will not be requested upon any subsequent accessing of programming mode.

Entering a set of codes

Entry of a set of codes avoids having to perform learning of all the transmitters or of all the badges in case of packages of 10, 50 or 100 pieces with

consecutive codes.

1. Access programming mode by pressing keys INC+DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F6 by pressing keys INC and DEC.

4. Confirm by pressing the VAL key. Request of the first location to be programmed will now appear, default value being 0001. Only the first

decimal point to the left will appear indicating that the initial location is being selected.

5. Select location by pressing keys INC and DEC, and confirm by pressing the VAL key.

6. Request of final location to be programmed will now appear. The value shown is the one which has been previously selected as the initial

location so that only a value greater than this can be selected by pressing keys INC and DEC. The last decimal point to the right will now appear

indicating that the final location is being selected.

7. After selection of the final location, confirm by pressing the VAL key. The M2000PE will now set itself up to accept transmission of a code. Once

code has been received (via radio or any of the connected readers), it is entered in the initial location. All subsequent locations up to the final

one may be entered with codes obtained by increasing the initial code by one unit.

Example: initial location = 120, final location = 127, received code = 112233

Upon all locations having been entered with the code, system will return to the function selection menu.

Deleting a set of codes

1. Access programming mode by pressing keys INC+DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F7 by pressing keys INC and DEC.

4. Confirm by pressing the VAL key. Request of the first location to be deleted

(that is, the default value 0001) will now appear. Only the first decimal point to the left will appear indicating that the initial location is being

selected.

5. Select location by pressing keys INC and DEC, and confirm by pressing the VAL key.

6. Request of final location to be deleted will now appear. The value shown is the one which has been previously selected as the initial location so

that only a value greater than this can be selected by pressing keys INC and DEC. The last decimal point to the right will now appear indicating

that the final location is being selected.

7. After having selected the final location, confirm by pressing the VAL key; the letter -C- will now appear on the left-hand side of the display.

8. Press the VAL key again to confirm. The M2000PE will now automatically delete all the codes stored in the set of programmed locations.

Upon deletion being completed, system will return to the function selection menu.

Deleting all codes

Deletion of all codes avoids having to scroll all locations and having to delete one code at a time in case of memory having to be fully cleared.

1. Access programming mode by pressing keys INC+DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F8 by pressing keys INC and DEC.

4. Confirm by pressing the VAL key. The letter C will appear on the left side of the display.

5. Confirm again by pressing the VAL key. The M2000PE will fully delete the code area only. All other stored parameters (relay times, channels,

etc.) will remain unaltered.

Upon deletion being completed, system will return to the function selection menu.

Serial transferring of data

1. Access programming mode by pressing keys INC+DEC.

2. Press the FUN key to access the function selection menu.

3. Select function F9 by pressing keys INC and DEC.

4. Confirm by pressing the VAL key. Request of the first location to be transferred (that is, the default value 0001) will now appear. Only the first

decimal point to the left will appear indicating that the initial location is being selected.

5. Select location by pressing keys INC and DEC, and confirm by pressing the VAL key.

6. Request of final location will now appear. The value shown is the one which has been previously selected as the initial location so that only a

value greater than this can be selected by pressing keys INC and DEC. The last decimal point to the right will now appear indicating that the

final location is being selected.

7. After having selected the final location, press the VAL key to confirm; the four lower segments in the display will now come on.

8. Press the VAL key again to confirm; this will initiate data transfer which while in progress will be signalled by the four segments in the lower part

of the display flashing.

Pressing of the FUN key at any time causes system to exit from data transfer mode and to return to the function selection menu.

If the FUN key is pressed while data is being transferred, the system in any case completes transfer of the code being processed, after which it exits

from this mode and returns to the function selection menu.

Location Code

120 ⇒112233

121 ⇒112234

122 ⇒112235

123 ⇒112236

124 ⇒112237

125 ⇒112238

126 ⇒112239

127 ⇒112240

M2000PE ENGLISH ISM2000PEEU_02_05.doc

Selecting the modalities for using the memory

It is possible to select three different modalities for using the code memory:

F: The codes entered via radio can activate either of the two relays, according to the assignment made with functions F3 and F4.

H: The memory is divided into two parts: lower part from location 1 to location 1000 (associated to PORT 1), upper part from location 1001 to location

2000 (associated to PORT 2).

This function is useful to manage two groups of different users in the same unit, to discriminate the activation of relay 1 or relay 2 with the same user

code (badge, radio, tag).

P: The anti-passback function is active: each code, once one of the two relays is activated (input), cannot be reactivated unless the other one is

activated first (output).

In order to select the modality:

1. Press keys INC and DEC at the same time

2. Press key FUN to access the select functions menu

3. Using keys INC and DEC select function F10

4. Confirm the selection with VAL: the display shows the current value of the modality

5. Using keys INC and DEC select modality F, H or P.

6. Confirm with key VAL: the display returns to selecting functions and the new modality is active

7. Press keys INC and DEC at the same time to exit programming

WARNING: By modifying the modalities for using the memory all previously stored codes are deleted.

In order to assign a remote control to relay 1 in modality H, store it by pressing channel 1 or channel 3. To assign it to relay 2, store it by pressing

channel 2 or channel 4.

Selecting the communication protocol

The control unit can dialog via the serial port by using two different communication protocols:

0: Communication with GTSYSTEM, M2000 or MKEYB.

1: Communication with printer PRINT2000

In order to select the protocol:

1. Press keys INC and DEC at the same time

2. Press key FUN to access the select functions menu

3. Using keys INC and DEC select function F11

4. Confirm the selection with VAL: the display shows the current value of the protocol

5. Using keys INC and DEC select protocol 0 or 1

6. Confirm with key VAL: the display returns to selecting functions and the new protocol is active

7. Press keys INC and DEC at the same time to exit programming

Printing the list of codes

In order to print the list of all the codes in the memory:

1. Set protocol 1 via function F11 (see Selecting the communication protocol)

2. Connect the printer PRINT2000 to the serial port

3. Select function F12

4. Press key VAL

When the printing is finished the control unit returns to the select functions menu.

Printing the events

If protocol 1 has been selected via function F11 (see Selecting the communication protocol), and the printer PRINT2000 is connected to the serial

port, each time a code is received a string will be printed containing the location, user status, user code, date, time and door, in the following format:

LOCATION STATUS USER CODE

DATE TIME DOOR

Type of event Print example

Valid Code POS.0001 VALID 00524602

01/12/00 04:59 DOOR1

Code not stored POS.0000 INVALID 00524999

Anti-passback (with modality P for using the memory) POS.0001 APB 00524602

03/12/00 11:04 DOOR1

The printer PRINT200 must have been previously programmed with the correct date and time.

Operating the system via the remote keyboard

The M2000PE may be connected to a terminal equipped with 4 keys and 4 displays for the remote programming, entering and deleting of codes.

Communication is made via an RS485 serial line.

Maximum link-up distance between the M2000PE and the M/KEYB keyboard/display is 500 metres.

The keys and displays of the remote terminal are exactly the same as those on the base unit both in terms of configuration and functions.

The M2000PE automatically detects the presence of the remote terminal, so that the same can be immediately controlled from the remote keyboard.

Programming cannot be made simultaneously on the central unit and the remote keyboard. In case of programming having been initiated from the

remote keyboard, the displays of the central unit will stay off and vice versa. This means that a programming operation initiated from the central unit

cannot be aborted from the remote keyboard and vice versa.

The terminal permits all M2000PE programming operations except the serial transfer of data from one central unit to another.

Note: Connect the central units as shown in the figure (maximum connection distance is 500 meters).

M2000PE ENGLISH ISM2000PEEU_02_05.doc

Diagram of terminal strips and keys:

M/2000E

18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

19 20 21 22 23 24

M/2000E

18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

19 20 21 22 23 24

Port 1 : enabling relay contact

FUN DEC INC VAL

YELLOW BLUE RED GREEN FUN DEC INC VAL

YELLOW BLUE RED GREEN

Port 2 : enabling relay contact Port 1 : enabling relay contact Port 2 : enabling relay contact

In case of the RS485 being used to connect MKEYB or GTSYSTEM, it is necessary that other M2000PEs which may have been connected

through terminals 21 and 22 be disconnected.

TERMINAL STRIP

1 Port 2: relay contact N.C. 13 Port 1: enabling contact relay

2 Port 2: relay common 14 Port 1: relay activation key

3 Port 2: relay contact N.O. 15 GROUND

4 Port 2: enabling contact relay 16 Port 1: data input (DATA1)

5 Port 2: relay activation key 17 Port 1: data input (DATA0)

6 GROUND 18 Port 1: output for reader power supply (9Vdc)

7 Port 2: data input (DATA1) 19 Antenna

8 Port 2: data input (DATA0) 20 Antenna braid

9 Port 2: output for reader power supply (9Vdc) 21 Serial line (RS485)

10 Port 1: relay contact N.C. 22 Serial line (RS485)

11 Port 1: relay common 23 Power supply, + 12-24Vac/dc

12 Port 1: relay contact N.O. 24 Power supply, - 12-24Vac/dc

Note: Make sure that terminals 4 and 13 are connected to terminals 6 and 15, respectively (see figure) in order to enable the corresponding relay

outputs 1 & 2. This contact is particularly useful for enabling, for instance, the relay outputs of the M2000PE via external devices such as buried

magnetic coils (opening command given by the M2000PE only in case of a vehicle being present on the coil so as to avoid undesired opening caused

by accidental radio transmission) or via timed relays (M2000PE enabled within a given time interval), as well as for closing the normally open contact

of a switch, and so on.