KEYKING 6630KE User manual

Proximity Keypads Reader
Operation Manual
Model: 6630KE/6630KDE
KEYKING GROUP LIMITED

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 1
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
Index
Chapter 1: Summarize.......................................................................................................................2
1.1 Summarize ..........................................................................................................................2
1.2 System Characteristics..................................................................................................3
Chapter 2: 6630KE System Instructions:..........................................................................................4
2.1 6630KE surface:............................................................................................................4
2.2 LED:..............................................................................................................................4
2.3 6630KE Wiring:............................................................................................................5
2.4 Mode setting:.................................................................................................................5
2.3.1 Wiegand 26 Bits................................................................................................6
2.3.2 Wiegand 34 Bits................................................................................................6
2.5 Communication Interface:.............................................................................................6
Chapter 3: Keypads Output..............................................................................................................7
3.1 Keypad Message ...........................................................................................................7
Chapter 4: Installation.......................................................................................................................8
4.1 Install on the wall (Based on Internal Back Box) .........................................................8
4.2 Install on the wall (Based on Surface Back Box)..........................................................9
4.3 Install on the wall (Surface, Without Back Box).........................................................10
4.4 Notes...........................................................................................................................12
Chapter 5: Configuaration...............................................................................................................13
5.1 Application: 6630KX Reader Display Setting..................................................................13
5.2 RS485 to RS232 converter................................................................................................14
5.3 Configuration Steps...........................................................................................................15
5.4 Change clock.....................................................................................................................16
5.4.1 Change clock by Keypads..............................................................................................16
5.4.2 Change clock by Configuration software.......................................................................16
5.4.3 Synchronize Clock by RS485 bus from Panel ...............................................................16

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 2
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
Chapter 1: Summarize
1.1 Summarize
Reader Model Define:
66 1 1K D E
Support Card Type:
E: EM; For example: EM4100, TK4100 series.
M: Mifare-; For example: Philips S50, S70 series smart cards.
RC: Mifare Sector; For example: Philips S50, S70 series smart cards.
H: HID Compatible; For example: 1326, 1386 and tags.
T: Temic, like E5557;
S: 15693; For example: Ti series cards.
B: TAP_B, For example: Chinese 2cd Identifitation;
C: TAP_C, Hongkong Metro;
E: EM; Proximity; 125KHz
H: HID Compatible; 125KHz
U: CPU, Mifare, RC; 13.56MHz
B: TAP_B, 2cd China ID; 13.56MHz
C: TAP_C, Hongkong Metro; 13.56MHz
K: Keypads Reader;
11: Model;
66: Series;
D: Display Built-in;

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 3
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
1.2 System Characteristics
Technical Parameters:
Power: 12 VDC ± 10%, 200mA
Dimensions: 90mm (H) x 90mm (W) x 22mm (D)
Weight: 200 grams
Operating Frequency:
125KHZ:
E: EM;
H: HID;
T: Temic;
13.56MHZ:
B: TAP_B;
C: TAP_C;
M: Mifare;
RC: Mifare Sector;
S: 15693;
•Read Range: 5 to 15 cm
•LED indicators: Dual LEDs, Blue&Green, or Red&Green.
•Back Ground Light: Blue.
•Display Screen: OLED, Dual Color: Yellow, Blue
Cover Back
90mm
90mm

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 4
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
Chapter 2: 6630KE System Instructions:
2.1 6630KE surface:
LED:
2.2 LED:
Blue LED for power indication.
Green LED for card reading indication.
Details of Keypads:
No. Mark Definition Output(BIN) No. Mark Definition Output(BIN)
1 1 Digital 1 0001 7 7 Digital 7 0111
2
2
Digital 2
0010
8
8
Digital 8
1000
3
3
Digital 3
0011
9
9
Digital 9
1001
4
4
Digital 4
0100
10
0
Digital 0
0000
5
5
Digital 5
0101
1
*
Cancel / Start
1010
6 6 Digital 6 0110 12 # Enter / Confirm 1100
LED (Blue&Green)
Back light
Keypads
Door Bell
Clock
Company
J4: Door Bell
J5: RS485
Sync Clcok interface
J2: Wiegand 26/34
J1: Connector

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 5
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
2.3 6630KE Wiring:
J2: Wiring Connector (Definition of wiring):
No. Mark Definition Note
1 +12V Power Supply
2 D1 Data 1
3 D0 Data 0
4 LED
LED control, when it was shorted with GND, then LED
will change the color.
5 GND GND, Ground Wire
6 BUZ Buzzer control, when it was shorted with GND, then
Buzzer will beep.
J3: Door Bell:
Normally the 2 wires are open.
When you press Door Bell Key, the 2 wires will be shorted.
2.4 Mode setting:
DIP Switch: Wiegand Selector:
OFF: the reader will output Wiegand 26 bits format.
ON: the reader will output Wiegand 34 bits format.
J4: Door Bell
J5: RS485
Sync Clcok interface
DIP: Wiegand 26/34
J1: Connector

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 6
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
2.3.1 Wiegand 26 Bits
Please keep DIP Switch on the OFF, then the reader will output Wiegand 26 bits
format.
2.3.2 Wiegand 34 Bits
Please keep DIP Switch on the ON, then the reader will output Wiegand 34 bits
format.
2.5 Communication Interface:
J5: RS485 Inteface:
Configuration interface with PC.
It can work with IC-232 or RS485HUB converter.
J5:
RS485+
RS485-

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 7
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
Chapter 3:Keypads Output
3.1 Keypad Message
The reader will processes the keypad entries in the reader and then transmits the data to the host
system via the Wiegand data lines. The reader outputs each key as an ASCII encoded hexadecimal
digit. The decoding of the message sent through the Wiegand interface is the only processing required
of the host system. The user interface has been implemented in the most generic fashion to give the
integrator the most flexibility.
The keypad message follows a basic format.
0 = 0000 4 = 0100 8 = 1000
1 = 0001 5 = 0101 9 = 1001
2 = 0010 6 = 0110 * = 1010
3 = 0011 7 = 0111 # = 1011
The reader will transmit every key value individually, after it was pushed.
For example:
If you push “1”, then the reader will transmit “0001” to the host (Panel or controller).
If you push “1” and “2”, then the reader will transmit “0001” to the host (Panel or controller), then
tranmit “0010” to the host.

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 8
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
Chapter 4: Installation
Installation Procedure:
4.1 Install on the wall (Based on Internal Back Box)
1. Install a Reader Back Box inside wall:Determine an appropriate mounting position for the
reader. Install a single or double standard electrical box (86*86mm) inside wall. If mounting to a
metal surface, drill two 7/64 (.109) inch holes and use the enclosed self tapping screws for
mounting.
a). Reader Back Box (Standard Electronic Box, single)b). Reader Back Box (Double)
2. Route: Route the interface cable from the reader to the Host.
3. Wiring: Install all wires to the green connector according below image.
4. Plug the Green Connector: Plug the green connector to the reader socket.
5. Set the JUMPER (Output mode): select W26 or W34 bits output of reader.
6. Mount the reader body: Mount the reader body to the Electronic Box (Reader Back Box) using the
two screws. Two #6-32 x 1 inch screws are provided for mounting to a gang box or metal surface.
7. Put the top cover and face plate.

KEYKING GROUP 6630KE Keypads Reader Operation Manual (1.00)
Page 9
Keyking Group Limited
33 Jabotinski St., Twin Tower 1, Ramat Gan, 52511,Israel
website: www.keyking.net E-mail: [e-mail]
4.2 Install on the wall (Based on Surface Back Box)
1. Install a Reader Back Box on wall:Determine an appropriate mounting position for the reader.
Install a single or double standard electrical box (86*86mm) on the wall using 4 screws.
a). Reader Back Box (Surface, Standard Electronic Box, single)
2. Route: Route the interface cable from the reader to the Host.
3. Wiring: Install all wires to the green connector according below image.
4. Plug the Green Connector: Plug the green connector to the reader socket.