Sewio Anchor 1.4 User manual

Sewio Networks, s.r.o,
www.sewio.net, email:[e-mail]
1
Anchor User Manual
V1.2
Anchor 1.4 User Manual
DIMENSIONS
70x74x25 mm
WEIGHT
72g
POWER SUPPLY
USB or Passive PoE
POWER
REQUIREMENTS
1.5W
USB DC 5V, ≈ 300mA
Passive PoE 48V, ≈ 30mA
TEMPERATURE
0 –50 °C
RADIO RANGE
15-50m*
UWB ANTENNA
Omnidirectional
WARM-UP TIME
20 minutes
PLACEMENT
For Indoor Use Only
Office, Warehouse, and Light industry environment.
*DEPENDS ON LINE OF SIGHT CONDITIONS, RADIO SETTINGS AND ENVIRONMENT

Sewio Networks, s.r.o,
www.sewio.net, email:[e-mail]
2
Anchor User Manual
V1.2
1Anchor Power Supply
There are two options to power the Anchor. It can be powered either via USB or Passive PoE. Only one
interface can be used at one time, never connect both.
▪Power Supply from USB –DC 5V, 500mA –mobile battery pack or USB Adaptor with maximum
cable length 1.8m.
Do not use longer USB cables, since cable voltage drop can cause instability of the device.
▪Power from Passive PoE Injector. DC voltage 24V/48V injected into unused Ethernet pairs
(Pairs 4,5 positive terminal, 7,8 negative terminal)
Always connect Anchor’s Ethernet to network infrastructure inside a building.
Always use galvanic isolated power adaptor with short circuit protection. Verified PN are:
GS36E24-P1J, GS36E48-P1J Meanwell.
Please note Passive PoE is not compliant with PoE IEEE 802.3af / Cisco. Anchor v1.3 cannot be powered
from those PoE ports. To use IEEE 802.3af Active PoE to power the Anchors, you need to get a converter
to the Passive PoE from the IEEE 802.3af.
Single-port Injector
Contains DC Jack, PoE Port and Lan port.
Multi-port Injector for 19” rack
“Data LAN” ports are connected to the network Switch, “Power+Data” ports are connected to the Anchors.
Never connect “Power+Data” ports to the computer or other network devices.
When the Anchors are connected to a stable power supply, a blue LED should start to blink on the side of
the enclosure.

Sewio Networks, s.r.o,
www.sewio.net, email:[e-mail]
3
Anchor User Manual
V1.2
2Default Configuration
Sync Channel
5
Sync RF Profile
RF3
Blink Channel
5
Blink RF Profile
RF3
IP Address
192.168.225.200
IP Mode
Static
*Default configuration could be changed please read the news on partner portal regarding the default
configuration.
To connect to the Anchor, you can use its native web interface:
1) Set your PC to the same IP scope as the Anchor. The recommended settings for your PC are:
IP Address: 192.168.225.1
Netmask: 225.255.255.0
2) Once your computer is on the same network, open your web browser and type in the IP Address of the
Anchor (default: 192.168.225.200). If the Anchor is properly connected and powered, you should see the
web interface of the device.
If you’re using more than one Anchor on the same network, be aware that they all have the same
IP address in default. You have to change the IP address of each Anchor, so an IP collision does
not occur.
To change the IP address of the Anchor, go to the web interface, change the Ethernet IP address and
netmask and press the “Submit” button and wait until the Anchor is restarted. Then the IP address is
changed.
Alternatively, you can also use the RTLS Manager to connect to the Anchor and change its’ IP
address:
1) Go to the RTLS Studio Software and launch the RTLS Manager by clicking its icon:
2) Go to the Anchors’ Settings tab. Change the IP address of each Anchor here. To confirm, press the
“Update” button:
Then the IP reconfiguration is finished and you should see the address changed in the RTLS Manager. Make sure
that the reconfigured Anchor is online.