SFS intec isoweld 3000 Instruction Manual

1
Original-Installationsanleitung DE 3
Installing Instructions EN 11
Instructions d’installation FR 19
Istruzioni per l’installazione IT 27
Manual de instalación ES 35
Installasjonsveiledning NO 43
Instrukcja montażu PL 51
Installatiehandleiding FL 59
Installationsvejledning DK 67
Installatiehandleiding NL 75
Руководство по установке RU 83
Installáció útmutató HU 91
Instalaþní návod CZ 99
Installationsinstruktion SV 107
Asennusohje FI 115
Version 1.02
System isoweld
TM3000
Distributed by: BEST MATERIALS ®
Ph: 800-474-7570, 602-272-8128 Fax: [phone]
www.BestMaterials.com Email: [email protected]

11
System components 12
Deciding on installation strategy 13
Preparing the roof for fastening 13
Measuring and marking fastening points 13
Fixing the stress plates 14
Rolling out the waterproof membrane 15
Marking the fastening points 15
Preparing the induction tool 16
Welding the membrane at the fastening points 17
English
Table of contents

12
Ensure that you have all required system components at your disposal.
System components
System components Product identification
Stress plate
FI-P
Sleeves
FI-R
Fastener
Setting tool
FI80
Induction tool
isoweldTM3000
Magnets
FI-Magnet
Hand inductor
FI-H
Calibration template
Pad for EPS/XPS
application
FI-Pad
Dist. by: BEST MATERIALS® | Ph: 800-474-7570
www.BestMaterials.com | Email: [email protected]

13
1. Deciding on installation strategy
2. Preparing the roof for fastening
3. Measuring and marking fastening points
 Familiarise yourself with the results of the wind load calculation and decide on the
procedure for the installation.
 Consider how best to deploy personnel, materials and equipment. In this way you
will achieve a fast, correct and efficient installation.
 Prepare the roof for laying out the waterproof membrane (e.g. prepare substrate,
vapour barrier, thermal insulation, fleece etc.).
 It is important to observe local regulations and manufacturers’ instructions.
We recommend that only so much roof area be prepared as can be fastened
and welded on the same day.
 Before rolling out the waterproof membrane, steps 3 and 4have to be carried out.
Measure the locations of the fastening points in accordance with the wind load
calculation and mark these on the prepared roof surface using e.g. a chalk line.

14
4. Fixing stress plates
underdriven correct overdriven
min. 2 mm
W
W
 Fix the stress plates in accordance with the wind load calculation.
 Use the specified fastener and preferably the FI80 hand setting tool.
Only set as many stress plates as can be welded on that day.
 Ensure that the stress plates are dry and clean, both in storage and during and
after installation.
 When installing on EPS/XPS thermal insulation, an FI-Pad must always be used,
even when a fleece is placed between the EPS/XPS thermal insulation and the
waterproof membrane.
 The FI-Pad must be placed directly under the stress plate.
 Check the setting depth of the stress plates (see figure below).
 The stress plates must be set parallel to the surface.
Incorrectly installed stress plates adversely affect the quality of the weld.
FI-Pad

15
6. Marking the fastening points
5. Rolling out the waterproof membrane
 Install the waterproof membrane in accordance with the membrane manufacturer’s
instructions.
Compared to seam fixing systems, the isoweldTM system makes it possible
to reduce the overlap of the waterproof membrane.
 Overlaps of the waterproof membrane in the area of the stress plate should be
avoided. See also the isoweldTM3000 operating instructions.
 Ensure that the underside of the waterproof membrane is dry.
 Use the isoweldTM3000 magnets (turning clockwise) or other suitable aids to mark
the top of the waterproof membrane above the stress plate.
Careful marking contributes significantly to a fast welding process.

16
7. Preparing the isoweldTM 3000 induction tool
Prepare the isoweldTM3000 induction tool for welding in accordance with the
separate operating instructions.
This includes in particular:
 unpacking and assembling the magnets
 unpacking and assembling the tool
 switching the tool on
 entering the waterproof membrane material
 entering the waterproof membrane thickness
 calibration
 test welding

17
11.
12. 13. 14. 15. 16.
19.
18.
17.
20.
.
1
.
.
.
1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
1. 2. 3. 4. 5. 6.
9.
8.
7.
10.
.
.
7.
8. Welding the membrane at the fastening points
Proceed with the welding process in accordance with the isoweldTM3000
operating instructions.
For an efficient process, we recommend the following procedure:
1. Place at least 10 magnets to the right of the points to be welded (A).
2. Weld the first of these points (B).
3. Place the magnet on to this fastening point within 3 seconds of completing the
welding (C).
4. Proceed to weld the following points 2 to 10 as described in steps 2and 3 (D).
5. Move the isoweldTM 3000 induction tool to the starting point of the next line (point 11)
(E).
6. Proceed to weld points 11 to 20 of the line on the left, as described in steps 2to 4.
7. etc.
1. 2. 3. 4. 5. 6.
9.
8.
7.
10.
.
.
.
7.
1.
2. 3. 4. 5. 6.
9.
8.
7.
10.
.
.
7.
1. 2. 3. 4. 5. 6.
9.
8.
7.
10.
.
.
7.
AB
CD
E

18
Fast and exact positioning of the magnet is a prerequisite for good welds.
 Ensure that all fastening points have been properly welded.
 Should you be uncertain about whether some welds have completed properly,
SFS intec recommends testing with a commercially available suction pad.
See also isoweldTM3000 operating instructions.
Distributed by: BEST MATERIALS ®
Ph: 800-474-7570, 602-272-8128 Fax: [phone]
www.BestMaterials.com Email: [email protected]