Shademaker Rope and Pole User manual

FOR
CONVENIENT STORAGE
Purchase pole case
Sold separately
See: To store
Page 2
INSTALLATION
INSTRUCTIONS
SHADEMAKER
DELUXE AWNINGS
For RV's, Campers, Trailers
and Patio Cover
REVIEW INSTALLATION INSTRUCTIONS PRIOR TO BEGINNING
INSTALLATION. CHECK CONTENTS OF PACKAGE WITH PARTS
LIST TO INSURE ALL PARTS ARE INCLUDED.
CAUTION
Do not allow water to collect
on the awning or roof of
shelter. When leaving your
unit for extended periods,
lower one corner to insure
proper water run off.
Make sure the installed unit
does not interfere with
operation of vehicle door(s)
y
If necessary install caster to
top corner of door(s) to make
sure door corner does not
tear installed unit.
When re-packing and storing
your unit keep the fabric
portion and hardware sep-
erate to avoid hardware from
tearing or puncturing your
unit.
This unit has been inspected
prior to being shipped from
the factory. Any manu-
facturing defects must be
reported prior to installation.
Damage to unit caused by faulty,
improper installation or abuse
will not be credited.

STEP # 2
(1
)
Do not allow water to
stand on canopy.
STEP # 3
ROPE TENSIONER USE
AWNING FABRIC

1
ea.
UPRIGHT TOP POLE (PIKED = 3 ea.
UPRIGHT BOTTOM POLE 
3 ea.
ROPE 
5 ea.
PLASTIC STAKE 9 INCHES

5 ea.
ROPE LOCK

5 ea.
1 " PLASTIC CAP

3 ea,.
ea.
4 ea.
4 ea.
6 ea.
6 ea.
6 ea.
4 ea.
KEY
NO
1
2
3
4
5
6
7
100-P -44
100-SOE -44
R6-10P
PS-9
P-ML
CAP
REPLACEMENT PARTS
WARNING
FLAMMABLE
Avoid flame and heat sources. This awning is made with flame
resistant fabric which meets CAPI-84 specifications. It is not
fireproof.
The fabric will burn if left in contact with any
flame source.
Do not apply any foreign substance to the fabric, it may
render the flame resistant properties ineffective.
SPECIAL SET UP INSTRUCTIONS
Use extreme caution in attaching awning to trailer. Three
people should assist to-prevent possibilty of material
being torn at juncture of top and header rope. Two people
should hold up flaked (or folded) canopy while third
person draws header rope through track of awning rail
on trailer.
SHADEMAKER PRODUCTS CORP
ShacIE
PO BOX 5271
MAKER
BUFFALO GROVE, IL 60089
Phone [phone]
MOST TRAILERS COME EQUIPPED WITH AN ALUMINUM RAIL TO ATTACH YOUR
AWNING. IN ABSENCE OF THIS RAIL INSTALL THE CORRECT LENGTH OF
STANDARD AWNING RAIL. THIS ITEM MAY BE PURCHASED AT LOCAL R.V.
DEALERS.
Spread end of rail with screwdriver
as shown to make insertion of awn-
ing fabric
easy.
Step #1 Insert plastic strip at top of
awning cover into awning
rail.
Step #2 Assemble uprights ( 2 & 3 ) as
shown. Attach plastic end cap
at bottom of each assembled
pole. Slip upper pike end of
pole through grommet of
awning cover.
Step #3 Loop
end
of rope ( 4 ), hook
it
over piked pole top. Guide
rope out at a 45 degree angle
and stake to ground. Adjust
rope length with rope slider.
Do not over stretch.
To Store Fold awning cover to a width
of 54 inches or less. Place
disassembled poles on folded
cover. Roll folded cover tightly
around poles. Store in main
compartment of bag. Place
stakes in plastic bag. Store bag
of stakes, ropes and hardware
in pocket
of storage bag.
Storage bag not supplied with
awning. Purchase separately.
1 Year lin1ited Warranty on material & worksmanship.