Shark 200T User manual

Doc# E149704 V.1.04 QS - 1
Shark® 200T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Shark® 200T Quickstart Guide
Mechanical Installation
Installation Steps: Slide top of groove of meter onto DIN Rail. Press gently until the meter clicks into
place. If mounting with DIN Rail provided, use Black Rubber Stoppers (also provided) shown above.
To remove meter, pull down on Release clip.
Electrical Installation: Select diagram to meet your application.
NOTE: Other wiring configurations are available. See the full Manual on the enclosed CD.
v
;CM=
v
CM
Ic Ib Ia
HI HI HI
LOLOLO
v
CM
v
CM
CM

CM

v
CM
DIN Installation 200T
Dimensions
DIN Rail with black
rubber stoppers
Release Clip
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
N
N
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
N
N
C
C
B
B
A
A
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
C
C
B
B
A
A
lc
HI
LO
lb
HI
LO
la
HI
LO
GND
Power
Supply
VRef
A
B
C
L (+)
N (-)
WYE direct, 3
phase, 4 wire
WYE with PTs, 3
phase, 4 wire
Delta direct, 3
phase, 3 wire
Delta with PTs, 3
phase, 3 wire
High
Side
Low
Side

Doc# E149704 V.1.04 QS - 2
Shark® 200T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Communication Wiring: The Shark®200T meter’s RS485 port
uses standard 2-wire, half duplex architecture.
Factory Initial Default Settings: When the Shark 200T is powered
up, for 10 seconds you can connect to the meter using the Factory
Default Settings (even if the Device Profile has been changed). After
10 seconds the Device Profile reverts to the actual Device Profile in
use. This is one way you can always connect to the meter. The
Factory Initial Default Settings are:
Device Address:1
Baud Rate:9600
Protocol:Modbus RTU
Connection Steps:
1.Open Communicator EXT software (download from
product CD).
2.Click Connect on the tool bar. You will see the
Connect screen, shown on the right. Make sure
your settings match these (use pull-down win-
dows).
3.Click Connect. The Device Status screen confirms
the connection.
4.Click OK. Communicator EXT’s Main screen opens.
Configuration Steps:
5.Click the Profile button on the tool bar.
The Device Profile screen opens. The Tree
menu on the left side of the screen lets you
choose setting screens.
6.Click Communications and select settings
based on your application (see instructions
below).
7.Click CT, PT Ratios and System Hookup
and select settings based on your applica-
tion (see instructions on the next page).
Communications Settings:
NOTE: The IrDA settings do not apply to the 200T.
COM2 (RS485): Enter the following settings:
Address (1-247)
Protocol (Modbus RTU, ASCII or DNP)
Baud Rate (9600 to 57600)
Response Delay (0-750 msec)

Doc# E149704 V.1.04 QS - 3
Shark® 200T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
CT, PT Ratios and System Hookup
Settings: Enter the following settings:
CT Numerator (enter value you want),
Denominator (display only), Multiplier (1,
10, or 100), CT Fullscale (Calculated auto-
matically)
PT Numerator (enter value you want),
Denominator (enter value you want),
Multiplier (1, 10, 100, or 1000), PT Fullscale
(Calculated automatically)
System Wiring: select from 3 Element Wye,
2.5 Element Wye, or 2 CT Delta.
NOTE: Voltage Full Scale = PT Numerator x PT Multiplier
Current Full Scale = CT Numerator x CT
Multiplier
IMPORTANT! Specify Primary and Secondary Voltage in Full Scale (NOT Ratios).
Example CT Settings:
200/5 Amps: Set Ct-n value as 200, Ct-S value as 1.
800/5 Amps: Set Ct-n value as 800, Ct-S value as 1.
2,000/5 Amps: Set Ct-n value as 2000, Ct-S value as 1.
10,000/5 Amps: Set Ct-n value as 1000, Ct-S value as 10.
Example PT Settings:
14,400/120 Volts: Set Pt-n value as 1440, Pt-d value as 120, Pt-S value as 10.
138,000/69 Volts: Set Pt-n value as 1380, Pt-d value as 69, Pt-S value as 100.
345,000/115 Volts: Set Pt-n value as 3450, Pt-d value as 115, Pt-S value as 100.
345,000/69 Volts Set Pt-n value as 345, Pt-d value as 69, Pt-S value as 1000.
Update Device:
8.When changes are complete, click the Update button to send a new profile to the Shark 200T meter.
9.Click Cancel to Exit the profile (or) click other tabs to update other screens.
10.Use Communicator EXT to communicate with the device and perform required tasks.
NOTE: For further details and additional programming screens (Password, Limits, Energy and Dis-
play), refer to the Shark User’s Manual & Communicator EXT 3.0 Software Manual on the enclosed CD.

Doc# E149704 V.1.04 QS - 4
Shark® 200T Quickstart
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
Electro Industries/GaugeTech
The Leader In Power Monitoring and Smart Grid Solutions
This page intentionally left blank.