Sharp KH-6V09CS00-EU User manual

KH-6V09CS00-EU
Cooking
Home Appliances

GB-Declaration of conformity
We declare that our products meet the applicable
European Directives, Decisions and Regulations
and the requirements listed in the standards
referenced.

EN - 2
CONTENTS:
OF THE HOB
SAFETY WARNINGS
INSTALLATION
Locating Your Built-in Hob
Electrical Connection of Your Hob
USE
Turn On and Turn Off the Control
Select Heater
Turn on dual- and triple zones
Set Cooking Level With and Without Heat Boost
Turn Off Individual Heaters
Timer Function
Key Lock
TOUCH CONTROL SAFETY FUNCTIONS
Sensor Safety Cut Off
Over Temperature Switch Off
Operating Time Limitations
Residual Heat Functions
CLEANING AND CARE

EN - 3
Single zone heater
Vitroceramic surface
Slide control panel
Note: The appearance of your hob maybe different than the model shown above
due to its conguration.
Dual zone heater
DESCRIPTION OF THE HOB
Dear Customer,
It is important for you to read this manual for best performance and to extend the
life of your appliance. We recommended you keep this manual for future reference.
Your new hob is under warranty and will provide lasting service. This warranty
is only applicable if the appliance has been installed and operated in accor-
dance with the operating and installation instructions detailed in this manual.

EN - 4
SAFETY WARNINGS
READ THESE INSTRUCTIONS CA-
REFULLY AND COMPLETELY BEFO-
RE USING YOUR APPLIANCE, AND
KEEP THEM IN A CONVENIENT PLA-
CE FOR REFERENCE WHEN NECES-
SARY.
THIS MANUAL IS PREPARED FOR
MORE THAN ONE MODEL. YOUR
APPLIANCE MAY NOT HAVE SOME
OF THE FEATURES THAT ARE EXP-
LAINED IN THIS MANUAL. WHILE
YOU ARE READING THE OPERATING
MANUAL, PAY A SPECIAL ATTEN-
TION TO THE EXPRESSIONS THAT
HAVE IMAGES.
General Safety Warnings
• This appliance can be
used by children aged
from 8 years and abo-
ve and persons with
reduced physical, sen-
sory or mental capabi-
lities or lack of experi-
ence and knowledge if
they have been given
supervision or instruc-
tion concerning use of
the appliance in a safe
way and understand
the hazards involved.
Children should not
play with the applian-
ce. Cleaning and user
maintenance shall not
be done by children
without supervision.
• WARNING: The app-
liance and its acces-
sible parts become
hot during use. Care
should be taken to
avoid touching the he-
ating elements. Child-
ren under the age of
8 should stand away
from the appliance
unless continuously
supervised.
• WARNING: Unatten-
ded cooking on a hob
with fat or oil can be
dangerous and may
result in re. NEVER
try to extinguish a re
with water. Switch off
the appliance and co-
ver the ame e.g. with
a lid or a re blanket.
• WARNING: Danger of
re: do not store items
on the cooking surfa-
ces.
• WARNING: If the sur-

EN - 5
face is cracked, switch
the appliance off to
avoid the possibility of
electric shock.
• For hobs incorpora-
ting a lid, any spillage
should be removed
from the lid before
opening. Additionally,
the hob surface sho-
uld be allowed to cool
before closing the lid.
• The appliance is not
intended to be ope-
rated by means of an
external timer or se-
parate remote-control
system.
• Do not use harsh ab-
rasive cleaners or
sharp metal scrapers
to clean the oven door
glass and other sur-
face since they can
scratch the surface,
which can cause the
glass to shatter or ca-
use damage to the
surface.
• Do not use steam
cleaners to clean the
appliance.
• Your appliance is produced in ac-
cordance with all applicable local
and international standards and
regulations.
• Maintenance and repair work must
be carried out only by authorized
service technicians. Installation
and repair work that is carried out
by unauthorized technicians may
endanger you. Altering or modif-
ying the specications of the app-
liance in any way is hazardous.
• Prior to installation, ensure that
the local distribution conditions
(nature of the gas and gas pressu-
re or electricity voltage and frequ-
ency) and the requirements of the
appliance are compatible. The re-
quirements for this appliance are
stated on the label.
• CAUTION: This appliance is de-
signed only for cooking food and is
intended for indoor domestic hou-
sehold use only and should not be
used for any other purpose or in
any other application, such as for
non-domestic use or in a commer-
cial environment or room heating.
• All possible security measures
have been taken to ensure your
safety. Since the glass may break,
you should be careful while clea-
ning it to avoid scratching. Avoid
hitting or knocking on the glass
with accessories.
• Ensure that the supply cord is not
wedged during the installation.
If the supply cord is damaged, it

EN - 6
must be replaced by the manufac-
turer, its service agent or similarly
qualied persons in order to pre-
vent a hazard.
Installation Warnings
• Do not operate the appliance be-
fore it is fully installed.
• The appliance must be installed
by an authorized technician and
put into use. The manufacturer is
not responsible for any damage
that might be caused by defective
placement and installation by una-
uthorized persons.
• When you unpack the appliance,
make sure that it is not damaged
during transportation. In the event
of any defect; do not use the appli-
ance and contact a qualied servi-
ce agent immediately. As the ma-
terials used for packaging (nylon,
staplers, styrofoam...etc.) may
cause harmful effects to children,
they should be collected and dis-
posed of immediately.
• Protect your appliance against
atmospheric effects. Do not expo-
se it to effects such as sun, rain,
snow etc.
• The surrounding materials of the
appliance (cabinet) must be able
to withstand a temperature of a
min. of 100°C .
• During use
• Do not put ammable or combus-
tible materials, in or near the appli-
ance when it is in operation.
• Do not leave the cooker while co-
oking with solid or liquid oils. They
may catch re as a result of of ext-
reme heating. Never pour water
on to ames that are caused by
oil. Cover the saucepan or frying
pan with its cover to choke the a-
me that has arisen in this case and
turn the cooker off.
• Always position pans over the
centre of the cooking zone, and
turn the handles to a safe positi-
on so they cannot be knocked or
grabbed.
• If you are not going to use the
appliance for a long time, remove
the plug from the socket. Keep the
main control switched off. Additio-
nally, when not using the applian-
ce, shut the gas valve off.
• Make sure the appliance control
knobs are always in the “0” (stop)
position when it is not being used.
• The temperature of the bottom
surface of the hob may increase
during the operation. Therefore, a
board must be installed underne-
ath the product.
• During cleaning and maintenance
• Always turn the appliance off befo-
re operations such as cleaning or
maintenance. You can do it after
removing the plug for the applian-
ce off or turning the main switches
off.
• Do not remove the control knobs
to clean the control panel.
• TO MAINTAIN THE EFFICIENCY
AND SAFETY OF YOUR APPLI-
ANCE, WE RECOMMEND YOU
ALWAYS USE ORIGINAL SPA-
RE PARTS AND ONLY CALL
OUR AUTHORIZED SERVICE

EN - 7
AGENTS SHOULD SUCH A
NEED ARISE.
INSTALLATION
The electrical connection of this hob
should be carried out by an authorized
service technician or a qualied electri-
cian, according to the instructions in this
guide and in compliance with the cur-
rent regulations.
• Before connecting your appliance to
the power line at home, make sure to
check the conformity of the voltage
settings, which are specied on the
information check the conformity of
the voltage settings, which are speci-
ed on the information available.
• The laws, regulations, directives and
standards in force in the country of
use are to be followed (safety regula-
tions, proper recycling in accordance
with the regulations, etc.)
Locating your built-in hob
After removing the packaging material
from the appliance and its accessories,
ensure that the hob is not damaged. If
you suspect any damage, do not use
the appliance and contact an autho-
rised service technician or a qualied
electrician immediately.
This built-in hob is to be inserted into a
cut out of the worktop.
Create an opening with the dimensions
shown in the next picture. The distance
between the rear edge of the hob and
any adjacent wall is dependant on the
wall's surface. Do not use easily com-
bustible material such as: curtains, pa-
per hear the hob.
520mm
590mm
41mm
560mm
490mm
Min.
A
Min.
B
Min.
130mm
Min.
25mm
• Apply the one-sided self-adhesive se-
aling tape supplied all the way round
the lower edge of the cooking surface
along the outer edge of the glass ce-
ramic panel. Do not stretch it.
• Screw the 4 worktop mounting brac-
kets on the side walls of the product
Neighbou-
ring walls A (mm) B (mm)
Combustible 60 150
Non-
combustible 25 40
worktop mounting
bracket

EN - 8
Electrical connection for your
hob
• . Before proceeding with the electri-
cal connection, verify that the current
carrying capacity of the system and
the socket is adequate for the maxi-
mum power rating of the hob.
• · Electrical installation of the residen-
ce and the electrical current plug in
use must be grounded and must con-
form with safety regulations.
• · If there is no dedicated hob circuit
and fused switch, they must be ins-
talled by a qualied electrician before
the hob is connected.
• The fused switch must be easily ac-
cessible once the hob has been ins-
talled.
• · Do not use adaptors, multiple soc-
kets and/or extension leads.
• This appliance conforms with the re-
quirements of the following EEC Di-
rectives:
1. Vitroceramic hob EEC/73/23 and
93/68, EEC/89/336 relating to radio
interference,
2. EEC/89/109 relating to contact with
foods.
• · A circuit breaker with a contact ope-
ning of at least 3 mm, rated 20 A and
delayed functioning type must be ins-
talled inside the supply circuit.
• For the touch controlled vitroceramic
hob, the cable must be H05VV-F
3X1,5 mm² / 60227 IEC 53. You will
nd the connection diagram shown on
the back of your appliance.
• During installation, please insure that
isolated cables are used. An incorrect
connection might damage your app-
liance. The warranty will not cover
such damages.
• All repairs must be carried out by an
authorized service technician or a
qualied electrician.
• ·Unplug your appliance before each
maintenance. For reconnection,
follow the connection diagrams
carefully.
The supply cable connection can differ
according to the terminal box type.
3x2,5 mm² 220V~
3x2,5 mm² 230V~
3x2,5 mm² 240V~
3x2,5 mm² 220V~
3x2,5 mm² 230V~
3x2,5 mm² 240V~
5x1.5 mm² 380V 3N~
5x1.5 mm² 400V 3N~
5x1.5 mm² 415V 3N~
5x1.5 mm² 380V 3N~
5x1.5 mm² 400V 3N~
5x1.5 mm² 415V 3N~
/

EN - 9
USE
The appliance is operated by pressing buttons and the functions are conrmed by
displays and sound signals.
MODE DESCRIPTION
Stand-By-Mode S-Mode The power lines are applied to the hob
control and all heater displays are off
or residual heat display is active.
Operating-Mode B-Mode At least one heater display shows a
heat setting between ‘0’ and ‘9’
Lock Mode VR-Mode The hob control is locked.
1 2 3 4 5 6
7 8 9 10 11 12
7- Stop/Go
8- Dual/Triple Zone Selection
9- Heat Setting/Timer Sliding
10- Key Lock indicator
11- Key Lock
12- On/Off
1- Heater Display
2- Active/Inactive Heater
3- Active/ Inactive Tımer
4- Timer Display
5- Cooking Zone Indicators Timer Function
6- Decimal Point

EN - 10
Turn On and Turn Off the
Appliance
If the appliance is in Stand-By-Mode, it
is put in Operating-Mode by pressing the
On/Off button for at least 1 second. The
sounding of a buzzer signal indicates a
successful operation.
On all heaters a ´0` appears and the
heater Decimal Point ashes (1 sec on,
1 sec off).
If there is no operation within 10 sec,
the display of all the heaters will turn off.
If the displays are turned off, the heater
will be set into Stand-By-Mode.
If is pressed for more than 2 seconds
(in Operating-Mode), the appliance
switches off and is set into Stand-By-
Mode again. The appliance can be turned
off by pressing at any time; even if
other buttons are pressed simultaneously.
If residual heat from a heater remains,
this will be indicated in the corresponding
heat setting Heater Display.
Select Heater
If a single heater is chosen with the
corresponding Active/Inactive Heater
Button , the Decimal Point of the related
Heater Display will ash. For the selected
heater, you can set the heat level between
1-9 by touching the Heat Setting Slider
Buttons
The slider button must be pressed within 3
seconds, otherwise the heater selection is
erased and heat setting dot will disappear
(Decimal Point). If there is no further
operation within 10 seconds, the heater
will fall back into the S-Mode.
The heat setting can always be changed
by pressing between
level 1-9.
Each sliding operation or each display
change is quitted by a buzzer signal.
Turning on dual and triple zones (available
only in some models)
Turning on the dual zone
The activation of the dual zone is done
after selecting the desired heater by
actuation . This is conrmed by a
buzzer signal. At the same time, the
corresponding Dual Zone Indicator goes
on statically. Pressing it for a second time,
the status of the dual zone toggles: it
changes from dual zone on to dual zone
off and back again.
The extension zone can be activated only
after a level between 1-9 is set on the
basic zone of the heater.
Turning on triple zones
A dual or triple zone can only be switched
on if the basic zone of a heater is set to
level 1–9 and the heater is selected, the
dot is on.

EN - 11
If is pressed, the buzzer signal sounds
and the Dual Zone Indicator is statically
on. If is pressed once again, another
signal is heard and the triple heater is
switched on. The Triple Zone Indicator
will be illuminated and the triple zone will
be energized.
After pressing once again, the triple
zone of the heater will be switched off
again. Each operation causes a status
change of the dual/triple zones following
in this manner (Dual zone on, triple zone
on, all extended zones off, dual zone on,
triple zone on, dual zone on, etc. ...)
Set Cooking Level With and Without Heat
Boost. All heaters are equipped with a
heat boost functionality.
If the heat boost is active, then the heater
will be operated with maximum power for
the period of the heat boost time, that is
dependent on the selected heat setting.
This is indicated through a ashing ´A`,
alternating with the heat setting value (e.g.
0.5 sec ´A` and 0.5 sec ´9`) in the heater
display. Once the heat boost time ends,
only the heat setting will be indicated.
If the heat boost should be used for a
heater, touch or slide the heat to level 0,
then touch heat level 9 again. After setting
the heat to level 9, ´A` will be indicated
alternating. This means that level 9 and
the heat boost is active now.
The heat boost can be turned off by sliding
your nger across the panel until heat
setting ´0` appears.
Turn Off Individual Heaters
A selective heater can be turned off with
3 different ways:
•Simultaneous operation of the right
and left part of the slider button
.
• Reduction of the heat setting to ´0` by
press the right and the left part of the
slider button .
•Use of timer turn off function for the
corresponding heater
Timer Function
The timer provides the following features:
The control can run a max. of 4 heater
assigned timers and 1 minute minder
(which is not assigned to any heater)
simultaneously. All timers can be used
only in B-Mode. A heater timer can only
be assigned to an active heater, running
in levels between 1-9. The minute minder
is independent of any heater.
In order to use both functions, the timer
function must be activated by the Active/
Inactive Timer button .
Pressing for the st time after activating
the heaters, the control proposes the
minute minder (no Cooking Zone Indicator
is ashing, they are all on or off).

EN - 12
Pressing for the second time, the
control proposes the assignment to one
of the activated heaters by ashing the
Cooking Zone Indicator. Now the timer
to the linked timer signalised.
Pressing again, the next timer in the
in the clockwise direction, is proposed
for assignment of the next active heater.
And so on…
Minute Minder
No matter whether a heater is activated or
not, the minute minder can be operated
by pressing . The appearing ´00`
shows that timer is active and the dot
in the right Timer Display indicates that
is now linked for setting
the timer value.
The minute minder is selected when all
Cooking Zone Indicators are statically
on or off (no Cooking Zone Indicator is
ashing).
With , the timer value
can be set.
After successful setting of the minute
minder time, the timer starts to decrement
the time.
The minute minder will not be stopped by
switching off the appliance or activating
the key lock function, it will proceed
increasing the minutes until run out
indication.
After reaching the ´00` of the timer, the
buzzer indicates that time has run out.
To stop the buzzer you have to conrm
the ´run out` by pressing any button.
Heater timer
Heater timers can be set only for activated
heaters (the heater level must be set
between 1-9)
The rst pressing of , activates the
minute minder. After pressing for the
second time, the timer is assigned to
the activated heater. The proposed
assignment is indicated by the related
Cooking Zone Indicator that is ashing.
Pressing again after activating the st
heater timer, the control recommends
the next active heater assigned to the
timer in the clockwise direction. The
assignment recommendation is indicated
by the ashing Cooking Zone Indicator.
Pressing , the timer
value for the heater can be set.
The running timer of the rst set heater
timer is indicated by the statically lighting
Cooking Zone Indicator.
Pressing once again assigns further
times to other activated heaters.
10 seconds after the last operation, the
timer display changes to the timer that
will run out next.

EN - 13
The assignment of that timer is displayed
always by a ashing Cooking Zone
Indicator. The number of timers running
can be identied by the number of Cooking
Zone Indicators that are statically on.
By toggling , you can display the
timer values for the heater timer and the
minute minder. The assignment is always
indicated by the ashing
Cooking Zone Indicator. If no Cooking
Zone Indicator is ashing, the minute
minder time is shown in the 2-digit Timer
Display.
All heater timers can be erased by
switching off the appliance into the S
Mode using . A minute minder will
not be erased, it will proceed until the
operation runs out.
To erase a timer in Operation Mode, you
rst have to select the timer by toggling
the Active/Inactive Timer Button until it is
displayed. The value can be erased in 2
different ways:
· Decrement by sliding your nger across
the panel until ´00`
appears on the Timer Display.
After reaching the ´00` of a heater timer,
the assigned heater level will be set to ´0`.
The heater timer or minute minder running
out is indicated by a buzzer tone. This
will be erased by pressing any button for
acknowledgement.
Key Lock
Key lock functionality is for blocking and
setting the appliance into safe mode
during operation. Touch modications as
for example rise heat settings and others
should not be possible. Only switching
the appliance off is possible.
The lock function becomes active, if the
Key Lock button is pressed for at least
2 sec. This operation is acknowledged
by a buzzer. After a successful operation
of more than 2 seconds, the Key Lock
Indicator ashes and the heater becomes
locked.
The heater can only be locked in Operating
Mode (B-Mode).
If the heater is locked, only can be
operated, all other buttons are blocked. If
there is any other button operated in the
blocked mode, the buzzer signal sounds
and the Key Lock Indicator ashes as
an indication for the activated key lock
functionality. Only the switch off by
operation of is possible. If you have
switched off the appliance, you can not
restart it again without unlocking it rst.
After pressing for 2 seconds, the Key
Lock indicator will disappear. Now, the hob
control is unlocked and can be operated
in normal order.

EN - 14
Child Lock
The purpose of the child lock functionality
is to lock the appliance in a complicated
multi-step process.
Child locking and unlocking is only
available in S-Mode.
First has to be pressed until the buzzer
beeps, then the the right and the left of
the slider button have to be pressed
for at least 0.5 sec, but for a max. of 1
second simultaneously. Following that,
the appliance can be locked the right of
the slider button. All 4 heaters display ´L`
is showed as a conrmation.
In the event the minute minder is still
running, it will proceed until ´00` is
reached and the timer will beep. After
conrmation of the timer running out, the
appliance will be fully locked. None of
the buttons can be used as long as the
appliance is locked.
The child lock is deactivated the same way
it was activated. After pressing until
the beep sounds, then the right and the
left of the slider button simultaneously for
at least 0.5 second, followed by pressing
only the left. As conrmation for successful
unlocking, the ´L` symbol in the displays
will be erased immediately.
Stop & Go
The Stop & Go function is used for pausing
the operation of the heaters during
cooking.White heaters are in operation,
if Stop & Go button is pressed for the
rst time, all the heaters will be turned
off. After pressing for the rst time, all
the heaters will be turned on.
Touch Control Safety Functions
The following safety functions are
available to avoid unintended operations
of the hob control.
Sensor Safety Cut Off
A sensor monitoring is included to prevent
the appliance from unwanted, random
sensor operation.
In the event one or more buttons are
pressed for longer than 12 seconds,
the sensor monitoring routine audibly
indicates that the wrong operation has
occurred (pot or other object placed on the
button, sensor failure, etc.) and switches
off the appliance.

EN - 15
The safety turn off results in the hob
control being turned off to S-Mode. An
´F` will ash in all heater displays.
If residual heat is present, it will be
displayed in all other heater displays.
The hob control will then go into S-Mode.
A buzzer signal will appear at the
same time After 10 minutes the buzzer
signalling will stop.
If there is no erroneous operation present
any longer, both the visual and the buzzer
signal will disappear.
Over Temperature Switch Off
Since the placement of the control is very
close to the heater in the middle front of
the hob, an incorrectly placed pot half
on the control, which is not sensed by
the sensor safety cut off (not covering a
button), heats up the hob to a very high
temperature, which makes the glass
and the buttons extremely hot, which
will result in burning.
To prevent the hob control unit from
damage, the control monitors all the
time the temperature and switches off
in case of overheating emergency.
It is indicated in heater 4 heater display
with the letter ´t`, for all the time until the
temperature decreases.
After the temperature falls, the ´t` displays
will be erased and the hob control unit
will fall back into the S-Mode. This means
that the user can reactivate the appliance
by touching .
Operating Time Limitations
The hob control unit has a limitation of
the operating time. If the heat setting for
this heater has not been changed for a
certain time, then the heater will turn
off automatically (´0` is displayed for 10
seconds, afterwards the residual heat).
The limit of the operating time depends
of the selected heat setting.
If a timer was associated with the heater,
then a ´00` will be displayed on the timer
display for 10 seconds, Afterwards, the
timer display will turn off.
After an automatic turn off of the heater, as
described above, the heater is operable
again and the maximum operating time
for this heat setting is applied.

EN - 16
Residual Heat Functions
After all cooking processes are
completed, there is some heat stored
in the vitroceramic glass referred to as
residual heat. The control can calculate
roughly how hot the glass is in the worst
case. If the calculated temperature is
higher than + 60 ° C, then this will be
indicated in the corresponding heater
display after the heater or the hob control
is turned off. The residual heat display is
shown as long as the calculated heater
temperature is > + 60 ° C.
The display of the residual heat has the
lowest priority and is overwritten by every
other display value, during safety turn offs
and displaying an error code.
After reapplying the supply voltage to
the hob control after an interruption of
the supply voltage has occurred, results
in the residual heat display ashing, if
the corresponding heater had a residual
heat of greater + 60 ° C before the power
interruption occurred. The display will
ash until the max. residual heat time
has expired or the heater is selected
and activated.
CLEANING AND CARE
Cookware with rough bottoms should
not be used since these can scratch the
glass ceramic surface. The bottoms of
good cookware should be as thick and
at as possible. Before use, make sure
that cookware bottoms are clean and
dry.
Always place the cookware on the co-
oking zone before it is switched on. If
possible, always place the lids on the
cookware. The bottoms of the cookwa-
re must not be smaller or larger than the
cooking zones, they should be at the
proper size as indicated below, not to
waste energy.
CORRECT FALSE
FALSE FALSE
Before cleaning the hob, rst remo-
ve the plug from the electrical supply
socket. Then ensure that there is no
residual heat stored in the appliance.
Vitroceramic glass is very resistant to
high temperatures and overheating. If
residual heat is stored in the appliance,
´H` will ash on the Heater Display. In
order to avoid burns, let the appliance
cool down.
Remove all split food and fat with a win-

EN - 17
dow scraper. Then wipe the hob with a
suitable washing up liquid and a clean
damp cloth. Rub the appliance using a
clean dry cloth.
If aluminium foil or plastic items are ac-
cidentally melted on the hob surface,
they should be removed immediately
from the hot cooking area with a scra-
per. This will avoid any possible dama-
ge to the surface. This also applies to
sugar or food containing sugar which
may be spilled on the hob.
In the event of other food melting on
the hob surface, remove the soil when
the appliance has cooled down. Use a
glass, ceramic or stainless steel cleaner
when cleaning the surface.
Do not use a dishcloth or abrasive
sponge to clean the vitroceramic sur-
face. These materials may damage the
surface.
Do not use chemical detergents, sprays
or spot removers on the vitroceramic
surface. These materials may cause
re or fading of the vitroceramic colour.
Clean with water and washing up liquid.
Remove all split food and fat with a win-
dow scraper. Then wipe the hob with a
suitable washing up liquid and a clean
damp cloth. Rub the appliance using a
clean dry cloth.
If aluminium foil or plastic items are ac-
cidentally melted on the hob surface,
they should be removed immediately
from the hot cooking area with a scra-
per. This will avoid any possible dama-
ge to the surface. This also applies to
sugar or food containing sugar which
may be spilled on the hob.
In the event of other food melting on
the hob surface, remove the soil when
the appliance has cooled down. Use a
glass, ceramic or stainless steel cleaner
when cleaning the surface.
Do not use a dishcloth or abrasive
sponge to clean the vitroceramic sur-
face. These materials may damage the
surface.
Do not use chemical detergents, sprays
or spot removers on the vitroceramic
surface. These materials may cause
re or fading of the vitroceramic colour.
Clean with water and washing up liquid.

Brand
Model
Type of Hob Electric
Number of Cooking Zones 4
Heating Technology-1 Radiant
Size-1
cm Ø14,5
Energy Consumption-1 Wh/kg 192,0
Heating Technology-2 Radiant
Size-2 cm Ø14,5
Energy Consumption-2 Wh/kg 192,0
Heating Technology-3 Radiant
Size-3 cm Ø18,0
Energy Consumption-3 Wh/kg 191,0
Heating Technology-4 Radiant
Size-4 cm 15,5x26,0
Energy Consumption-4 Wh/kg 190,0
Energy Consumption of Hob Wh/kg 191,3
This hob complies with EN 60350-2
Energy Saving Tips
Hob
- Use cookwares having flat base.
- Use cookwares with proper size .
- Use cookwares with lid.
- Minimize the amount of liquid or fat.
- When liquid starts boiling , reduce the setting.
KH-6V09CS00-EU

1
Service &
Support
Visit Our Website
sharphomeappliances.com
52299733