Sharp Aquos LC-26GA6E User manual

LCD COLOUR TELEVISION
LCD-FARBFERNSEHGERÄT
TÉLÉVISION COULEUR À ÉCRAN
À CRISTAUX LIQUIDES (LCD)
TELEVISORE A COLORI LCD
LCD-KLEURENTELEVISIE
TELEVISIÓN EN COLOR LCD
OPERATION MANUAL
BEDIENUNGSANLEITUNG
MODE D’EMPLOI
MANUALE DI ISTRUZIONI
GEBRUIKSAANWIJZING
MANUAL DE MANEJO
SHARP CORPORATION
LC-26GA6E LC-32GA6E LC-37GA6E
Printed in Malaysia
Gedruckt in Malaysia
Imprimé en Malaisie
Stampato in Malesia
Gedrukt in Maleisië
Impreso en Malasia
TINS-B900WJZZ
05P07-MA-NG
OPERATION MANUAL MANUALE
DI ISTRUZIONI
BEDIENUNGSANLEITUNG
GEBRUIKSAANWIJZING
LC-26GA6E
LC-32GA6E
LC-37GA6E
MODE D’EMPLOI
MANUAL DE MANEJO
B900WJZZ 1
ENGLISH
FRANÇAIS DEUTSCH
ITALIANO
NEDERLANDS
ESPAÑOL
PIN
Printed on environmentally friendly paper
Auf ökologischem Papier gedruckt
Imprimé sur papier écologique
Stampato su carta ecologica
Afgedrukt op ecologisch papier
Impreso en papel ecológico

(567,9) / [700,4] / ((822,6))
(567.9) / [700.4] / ((822.6))
(556) / [638] / ((707))
(407) / [479] / ((548))
(504) / [576] / ((645))
(52) / [62] / ((62))
(278) / [307] / ((307))
(519) / [677] / ((677))
(421) / [473] / ((473))
(355) / [400] / ((435))
108
(663) / [795] / ((917))
(57) /
[109] /
((109))
(320,6) / [395,1] / ((463,8)) (320.6) / [395.1] / ((463.8))
3,1
3.1
(100)
(100)
(50)
[200] / ((200))
[115] / ((104))
[200] / ((200))
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should
the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or
ASA
and of the same rating
as above, which is also indicated on the pin face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the
mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of
in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet, as a serious
electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT:
The wires in the mains lead are coloured in accordance with the following code:
Blue: Neutral
Brown: Live
As the colours of the wires in the mains lead of this product may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
• The wire which is coloured blue must be connected to the plug terminal which is marked N or coloured black.
• The wire which is coloured brown must be connected to the plug terminal which is marked L or coloured red.
Ensure that neither the brown nor the blue wire is connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
• If the new fitted plug contains a fuse, its value is the same as that removed from the cut-off plug.
• The cord grip is clamped over the sheath of the mains lead, and not simply over the lead wires.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
LC-26/32/37GA6E
LC-26GA6E LC-32/37GA6E
( ) : LC-26GA6E
[ ] : LC-32GA6E
(( )) : LC-37GA6E
: LC-26/32/37
GA6E

1
Contents ……………………………………………………………………… 1
Dear SHARP customer ………………………………………………………… 2
Important Safety Precautions ……………………………………………… 2
Supplied accessories ………………………………………………………… 2
Preparation ……………………………………………………………………… 3
Setting the TV ……………………………………………………………… 3
Inserting the batteries …………………………………………………… 4
Using the remote control unit …………………………………………… 4
Cautions regarding the remote control unit ……………………… 4
Part names ……………………………………………………………………… 5
Remote control unit ……………………………………………………… 5
TV (Front view) …………………………………………………………… 6
TV (Rear view) …………………………………………………………… 6
Using external equipment …………………………………………………… 7
EXT 1 ……………………………………………………………………… 7
EXT 2 ……………………………………………………………………… 7
EXT 3 ……………………………………………………………………… 7
EXT 4 and 5 ……………………………………………………………… 7
PC INPUT ………………………………………………………………… 7
Watching TV …………………………………………………………………… 8
Turning on the power …………………………………………………… 8
Turning off the power ……………………………………………………… 8
Standby/On ………………………………………………………………… 8
Initial auto installation …………………………………………………… 8
Menu operations ……………………………………………………………… 9
Menu operation buttons ………………………………………………… 9
On-Screen Display ……………………………………………………… 9
PICTURE menu ………………………………………………………… 10
Using PICTURE menu screen ………………………………… 10
LEVELS …………………………………………………………… 10
PICTURE MODE …………………………………………… 10
Picture adjustments (CONTRAST/BRIGHTNESS/
COLOUR/SHARPNESS/BACKLIGHT/OPC) ……… 10
ADVANCED ……………………………………………………… 10
I/P SETUP …………………………………………………… 10
MOV. COMP. (MOVEMENT COMPENSATION) ………… 10
COMB FILTER ……………………………………………… 10
NOISE RED. (NOISE REDUCTION) ……………………… 10
DYN. CONTRAST (DYNAMIC CONTRAST) …………… 10
DYN. GAMMA (DYNAMIC GAMMA) …………………… 10
MONOCHROME …………………………………………… 11
COLOUR TEMP. (COLOUR TEMPERATURE) ………… 11
NTSC HUE ………………………………………………… 11
SOUND menu …………………………………………………………… 11
Using SOUND menu screen …………………………………… 11
EFFECTS ………………………………………………………… 11
SOUND EFFECTS ………………………………………… 11
LEVELS …………………………………………………………… 11
SPEAKERS ………………………………………………… 11
VOLUME ……………………………………………… 11
BALANCE …………………………………………… 11
LOUDNESS ………………………………………… 11
AUTO VOL. (AUTO VOLUME) …………………… 11
DYNAMIC BASS …………………………………… 12
EXTERNAL ………………………………………………… 12
SCART VOLUME …………………………………… 12
AV VOLUME ………………………………………… 12
EQUALIZER ……………………………………………………… 12
STEREO …………………………………………………………… 12
SPEAKERS ………………………………………………… 12
AV ………………………………………………………… 12
SOUND IDENT. (SOUND IDENTIFICATION) …………… 12
FEATURES menu ……………………………………………………… 12
Using FEATURES menu screen ………………………………… 12
TIMERS …………………………………………………………… 13
DATE ………………………………………………………… 13
TIME ………………………………………………………… 13
ON TIMER (Wake-up timer) ……………………………… 13
OFF TIMER (Sleep timer) ………………………………… 13
RADIO/TV …………………………………………………… 13
VOL. LIMIT (VOLUME LIMIT) …………………………… 13
Contents
OPERATION MANUAL ENGLISH
• The illustrations and on-screen displays in this operation manual are for explanation purposes and may vary slightly from the actual
operations.
• The examples used throughout this manual are based on the LC-32GA6E model.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
AV-LINK …………………………………………………………… 13
AVL CONTROL (AV-LINK CONTROL) …………………… 14
AVL TIMERS (AV-LINK TIMERS) ………………………… 14
DATE ………………………………………………… 14
START ………………………………………………… 14
STOP ………………………………………………… 14
MODE ………………………………………………… 14
SPEED ……………………………………………… 14
DEMO ……………………………………………………………… 14
CHILD LOCK …………………………………………………… 14
LOCK ALL ………………………………………………… 14
TYPE ………………………………………………… 14
START ………………………………………………… 14
STOP ………………………………………………… 14
LOCK PROGRAM ………………………………………… 14
TYPE ………………………………………………… 15
PROGRAMME ……………………………………… 15
START ………………………………………………… 15
STOP ………………………………………………… 15
CHANGE PIN ……………………………………………… 15
CLEAR LOCK ……………………………………………… 15
SETUP menu …………………………………………………………… 15
Using SETUP menu screen …………………………………… 15
AUTO INSTALLATION …………………………………………… 15
MANUAL TUNE ………………………………………………… 15
TYPE ………………………………………………………… 15
SYSTEM …………………………………………………… 16
CHANNEL ………………………………………………… 16
MODE ……………………………………………………… 16
FINE TUNE ………………………………………………… 16
SCAN ……………………………………………………… 16
EDIT ……………………………………………………………… 16
EDIT ………………………………………………………… 16
DELETE …………………………………………………… 16
SORT ……………………………………………………… 16
GENERAL SETUP ……………………………………………… 17
OSD LANGUAGE ………………………………………… 17
FACTORY SETTINGS ……………………………………… 17
TTX CHAR. SET
(TELETEXT CHARACTER SET) …………………… 17
WSS (Wide Screen Signalling) …………………………… 17
ROTATION ………………………………………………… 17
AV SETUP ………………………………………………………… 17
HDMI SETUP ……………………………………………………… 17
DVI SETUP VIA HDMI …………………………………………… 17
POWER CONTROL ……………………………………………… 18
POWER MANAGEMENT ………………………………… 18
NO SIGNAL OFF …………………………………………… 18
NO OPERATION OFF ……………………………………… 18
Useful adjustment settings and features ……………………………… 18
PC INPUT mode adjustments ………………………………………… 18
PICTURE/SOUND adjustments ………………………………… 18
Image position …………………………………………………… 18
PC compatibility chart …………………………………………… 18
HD mode adjustments ………………………………………………… 19
FM Radio menu screen ………………………………………………… 19
Radio Setting …………………………………………………… 19
Auto Station Search ……………………………………………… 19
Manual Station Search ………………………………………… 19
WIDE MODES …………………………………………………………… 20
Manual selection ………………………………………………… 20
Auto selection …………………………………………………… 20
Teletext function ………………………………………………………… 20
Appendix …………………………………………………………………… 21
Troubleshooting ………………………………………………………… 21
IMPORTANT NOTE ON DISENGAGING
ADVANCED CHILD LOCK ……………………………………… 21
Specifications …………………………………………………………… 22
Corresponding real channel ………………………………………… 23
End of life disposal …………………………………………………… 24
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.
ENGLISH
LC-26/32/37GA6E(E)_a 05.6.29, 7:48 AM1

2
Thank you for your purchase of the SHARP LCD colour TV product. To ensure safety and many years of trouble-free
operation of your product, please read the Important Safety Precautions carefully before using this product.
Dear SHARP customer
• Cleaning—Unplug the AC cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not
use liquid cleaners or aerosol cleaners.
• Water and moisture—Do not use the product near water, such as bathtub, washbasin, kitchen sink, laundry tub, swimming
pool and in a wet basement.
• Do not place vases or any other water-filled containers on this product.
The water may spill onto the product causing fire or electric shock.
• Stand—Do not place the product on an unstable cart, stand, tripod or table. Doing so can cause the
product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting
the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware
recommended by the manufacturer.
• When relocating the product placed on a cart, it must be moved with utmost care. Sudden stops, excessive
force and uneven floor surface can cause the product to fall from the cart.
• Ventilation—The vents and other openings in the cabinet are designed for ventilation. Do not cover or block
these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the
product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation
openings. This product is not designed for built-in installation; do not place the product in an enclosed place
such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.
• The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or impact applied.
If the LCD panel is broken, be careful not to be injured by broken glass.
• Heat sources—Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating products
(including amplifiers).
• To prevent fire, never place any type of candle or naked flames on the top or near the TV set.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
• There is power consumption always if main plug is connected.
The LCD panel is a very high technology product, giving you fine picture details.
Due to the very large number of pixels, occasionally a few non-active pixels may appear on the screen as a fixed
point of blue, green or red.
This is within product specifications and does not constitute a fault.
Precautions when transporting the TV
When transporting the TV, never carry it by holding onto the speaker. Be sure to always carry the TV by two people
holding it with two hands—one hand on each side of the display.
Remote control unit (g1) AC cord (g1)
Page 4 and 5
Product shape varies in
some countries.
Page 3
• “AAA” size battery (g2) .............. Page 4
• Operation manual
Important Safety Precautions
Supplied accessories
Cable clamp (g1)
Page 3
Cable tie (g1)
Page 3
LC-26/32/37GA6E(E)_a 05.6.29, 7:48 AM2

3
Preparation
Setting the TV
Bundling the cables
NOTE
• The illustration shows the LC-32GA6E.
To TV antenna terminal
To FM antenna terminal
Standard DIN45325 plug
(IEC 169-2)
75-ohm coaxial cable
FM antenna cable
Removing the terminal cover
Press the two hooks and slide the cover toward
the left of TV to remove. TV (Rear view)
AC cord
Product shape varies
in some countries.
Cable clamp
Cable tie
LC-26/32/37GA6E(E)_a 05.6.29, 7:48 AM3

4
Preparation
CAUTION
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.
• Do not mix batteries of different types. Different types of batteries have different characteristics.
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage in old
batteries.
• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you find any chemical leakage,
wipe thoroughly with a cloth.
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.
• If you will not be using the remote control unit for an extended period of time, remove the batteries from it.
30°
30°
Remote control sensor
7 m
1Press and slide the battery cover to open it.
2Insert two supplied “AAA”size batteries.
• Place batteries with their terminals corresponding to the
(e) and (f) indications in the battery compartment.
3Close the battery cover.
Inserting the batteries
Before using the TV for the first time, insert two “AAA” size batteries (supplied). When the batteries become depleted and
the remote control unit fails to operate, replace the batteries with new “AAA” size batteries.
Using the remote control unit
Use the remote control unit by pointing it towards the remote control sensor. Objects between the remote control unit and
the sensor may prevent proper operation.
ECautions regarding the remote control unit
• Do not expose the remote control unit to shock.
In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.
• Do not install or place the remote control unit under direct sunlight. The heat may cause deformation of the unit.
• The remote control unit may not work properly if the remote control sensor of the TV is under direct sunlight or strong
lighting. In such case, change the angle of the lighting or TV, or operate the remote control unit closer to the remote
control sensor.
LC-26/32/37GA6E(E)_a 05.6.29, 7:49 AM4

5
Remote control unit
Part names
RADIO
Displays the RADIO menu screen
and make adjustments for
FM RADIO mode.
(See page 19.)
3(Hold)
Temporarily holds the
current Teletext page.
(See page 20.)
B(Standby/On)
Turns on and off the power or
enters Standby mode.
(See page 8.)
[(Subtitle)
Displays the Teletext
Subtitle directly.
(See page 20.)
END
Exit the menu item.
i(e/f) (Volume)
i(e) Increases the volume.
i(f) Decreases the volume.
Programme select
Changes programmes or sets the
page in Teletext mode.
A(Flashback)
Returns to the previous
programmes or sources.
2(Sound Mode Selector)
Displays the “SOUND STEREO”
menu screen directly. (See pages
11 and 12.)
Virtual
Displays the “SOUND EFFECTS”
menu screen directly.
(See page 11.)
1 (Clock/Subpage)
Displays time in TV mode. (When
available).
Displays the Teletext Subpage in
Teletext mode. (See page 20.)
TIMER
Displays the “FEATURE TIMERS”
menu screen directly.
(See page 13.)
k(Reveal)
Displays hidden information such
as solutions to riddles and puzzles
in Teletext mode.
(See page 20.)
p(Display/Info)
Displays the programme
information.
m(Teletext)
Displays the Teletext mode screen.
(See page 20.)
e(Mute)
Switches the sound on and off.
b(Input mode)
Displays the “EXT. SOURCES
MENU” menu screen. (See page
7.)
f(WIDE MODES)
Displays the “WIDE MODES” menu
screen directly, to select your
desired screen size.
(See page 20.)
Sets the area of magnification in
Teletext mode. (See page 20.)
MENU
Displays the menu. (See page 9.)
P (r/s)
r Increases programme number.
s Decreases programme number.
Red
Displays the “PICTURE LEVELS”
menu screen directly.
(See page 10.)
Select a desired level or item.
OK
Go to the next step or execute the
item.
Green
Displays the “SOUND SPEAKER
LEVELS” menu screen directly.
(See page 11.)
Programmes List, Upwards/
Downwards Selection
Colour (Red/Green/Yellow/Blue)
Select a page in Teletext mode.
(See page 20.)
LC-26/32/37GA6E(E)_a 05.6.29, 7:49 AM5

6
TV (Front view)
Part names
TV (Rear view)
TV/FM Radio antenna input
terminals
OPC sensor
Remote control sensor
Standby/On indicator (B)
OPC indicator
Power button (a)
Input button (b)
Volume buttons ( il/k)
Programme buttons (Ps/r)
WAKE-UP (ON TIMER) indicator
EXT 1 (RGB) terminal
EXT 3 terminals
AV OUTPUT terminals
Headphone jack
PC INPUT terminals
EXT 2 (AV) terminal
EXT 4 (COMPONENT/AUDIO)
terminals
AC INPUT
terminal
EXT 5 (HDMI/AUDIO) terminals
LC-26/32/37GA6E(E)_a 05.6.29, 7:49 AM6

7
Using external equipment
You can connect many types of external equipment to your TV, like a decoder, VCR, DVD player, PC, game console and
camcorder. To view or select the input source, see the operations below.
Using bon the TV: Press b. Each time you press b, the input source will change. TV s EXT1 s EXT2 s EXT3 s
EXT4 s EXT5 s PC s RADIO s TV
Using bon the remote control unit: Press bto display the “EXT. SOURCES MENU” screen. Press a/bto select
your desired input source, and then press OK. TV/EXT1/EXT2/EXT3/EXT4/EXT5/PC INPUT
NOTE
• Before connecting external equipment to your TV, see page 17.
• The cables marked with * are commercial items.
EXT 1
You can use the EXT 1 terminal when connecting a decoder
and other audiovisual equipment.
EXT 2
You can use the EXT 2 terminal when connecting a VCR
and other audiovisual equipment.
NOTE
• TV-VCR advanced “AV LINK” systems may not be compatible
with some external sources.
NOTE
• The S-VIDEO terminal has priority over the VIDEO terminals.
• You can also connect the game console to EXT 1 or 2 terminals
to enjoy clearer picture.
VIDEO S-VIDEOL-AUDIO-R
AV OUTPUT
EXT 3
A game console, camcorder and some other audiovisual
equipment are conveniently connected using the EXT 3
terminals.
or
EXT 4 and 5
You can use the EXT 4 (COMPONENT) or 5 (HDMI) terminals
when connecting to a DVD player and other audiovisual
equipment.
L-AUDIO-R
AV OUT
YP
B
( C B)
P R
( C R)
COMPONENT
PC INPUT
Use the PC INPUT terminals to connect a PC.
NOTE
• The PC INPUT terminals are DDC1/2B-compatible.
SCART cable*
SCART cable* SCART cable*
S-video
cable*
AUDIO
cable*
VCR, DVD player or
Decoder
VCR VCR or DVD
player
Game console Camcorder
DVD player or Decoder
When using an HDMI-DVI conversion
cable, input the Audio signal to
AUDIO terminal of EXT 5.
DVD player or Decoder
PC
PC
Composite video cable*
AUDIO cable*
Component cable*
HDMI cable*
RGB/DVI
conversion cable*
RGB cable*
ø 3.5 mm stereo
minijack cable*
ø 3.5 mm stereo
minijack cable*
LC-26/32/37GA6E(E)_a 05.6.29, 7:49 AM7

8
Turning on the power
Press aa
aa
a(Power) on the TV.
• The Standby/On indicator on the TV changes from red to green.
Watching TV
Initial auto installation
When the TV powers on for the first time after purchase, the
initial auto installation is invoked. You can set language,
country and automatically search for and store all the
receivable TV and FM radio channels.
NOTE
• The initial auto installation function only once. If the Initial auto
installation is not completed, (ex: When menu screen
disappeared by not operating for a few minutes, when the power
shut down, etc.), try “AUTO INSTALLATION” from the “SETUP”
menu. (See page 15.)
1Setting the on-screen display language
1Press a/bto select “SELECT LANGUAGE”.
2Press c/dto select the desired language listed on the
screen.
2Setting the country or area
1Press a/bto select “SELECT COUNTRY”.
2Press c/dto select your country or area listed on the
screen.
NOTE
• The TV set is ready to preset automatically all local channels for
you.
• If you do not intend to use your TV set with a VCR then proceed
to step 3.
• If the TV set is being used with a VCR, turn on the VCR and play
back a pre-recorded tape. The signal from the RF terminal of
your VCR is assigned to a TV programme.
Turning off the power
To turn off the power, press aa
aa
a(Power) on the TV again.
• The Standby/On indicator on the TV gradually turns off.
• When the TV is turned off by aa
aa
a(Power), you cannot turn on the
power by pressing Bon the remote control unit.
NOTE
• If you are not going to use this TV for a long period of time, be
sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when a a
a a
a (Power) is
turned off.
Standby/On
Press Bon the remote control unit.
• The TV enters Standby mode and the image on the screen
disappears.
• The Standby/On indicator on the TV changes from green to red.
Watching TV
The setup menu disappears and you can watch the
programme.
3Press OK to start Auto Channel Preset.
•Automatic Channel Sorting System (ACSS):
The TV searches for frequencies, memorises the channels
found, and sorts them (according to technical criteria).
For TV channels: from Pr-01 to a maximum of 99
programmes.
For FM RADIO channels: from Pr-01 to a maximum of 99
programmes.
• This tuning process may take several minutes to perform.
•You do not need to do anything during the Auto
Channel Preset.
4When the Auto Channel Preset is completed, the “EDIT”
menu screen displays.
• In this menu you can change the order of the channels,
delete channels, and change or give the channels an eight-
letter name.
Available options in EDIT Menu screen
• For more details about “EDIT” menu screen, see page
16.
Button Mode Description
c/dTV or RADIO To select the programmes
of “TV” or “RADIO”.
a/bSELECT To select a programme
from the list.
Yellow DELETE Use this mode for
cancelling channels which
are badly tuned or
repeated.
Red EDIT Use this mode for giving a
name made up of eight-
letter to the channels or for
changing the one which
appears on some
channels.
Blue SORT Use this mode for sorting
the channels into the
desired programme (Pr).
END EXIT To return to the normal
screen.
LC-26/32/37GA6E(E)_a 05.6.29, 7:49 AM8

9
Menu operations
On-Screen Display
Menu
Press MENU to display On-Screen Display.
Example:
Menu operation buttons
Use the following buttons on the remote control unit to
operate the menu.
MENU: Press to open the menu screen.
a/b/c/d:Press to select a desired item on the
screen or adjust a selected item.
OK: Press to go to the next step or execute
the item.
END: Press to exit the menu item.
Colour buttons: Press to go to the menu item screen
and select a desired item on the menu.
PICTURE
Top Menu name
: PICTURE (See page 10.)
: SOUND (See page 11.)
: FEATURES (See page 12.)
: SETUP (See page 15.)
2Sub Menu
Press OK to move to next screen (Menu item).
• Press a/bto select your desired Sub Menu.
• The selected item is displayed in yellow letters with red
background. Press OK to move to next screen (More
options or Menu item).
3More options
When more options appear, press a/bto select your
desired item.
• The selected item is displayed in yellow letters with red
background.
Press OK to display the next screen.
4Operation guidance for the remote control
Follow the operation guidance to adjust/set.
Example: Menu item
1Top Menu
Press c/dto select your desired Top Menu.
Example: Top Menu
SOUND
EFFECTS
LEVELS
EQUALIZER
STEREO
MOVE SELECT EXIT
SPEAKERS
EXTERNAL
1
2
PICTURE LEVELS
PICTURE MODE
CONTRAST
BRIGHTNESS
COLOUR
40
50
80
USER
USER
DYNAMIC
STANDARD
MOVIE
GAME
SELECT ADJUST EXIT
7
8
65
9
5Selected menu item.
6Item currently selected.
7Items available to be set.
8The items for LEVELS menu.
• Press a/bto select your desired items.
9Indication of the next screen.
• Press bto display the next screen.
4
3
LC-26/32/37GA6E(E)_b 05.6.29, 7:49 AM9

10
PICTURE menu
Menu operations
EUsing PICTURE menu screen
USER: Select this mode in order to recover the “PICTURE” level
(“CONTRAST”, “BRIGHTNESS”, “COLOUR”, “SHARPNESS”
“BACKLIGHT”, and “OPC”) that you had adjusted at the last
time. Each time you change one of these adjustments, it is
memorized automatically within the option “USER”.
DYNAMIC: This mode has been designed for a clear-cut image
emphasising high contrast for sports viewing.
STANDARD: Select this mode if you wish to normalize
“PICTURE” levels to default factory settings.
MOVIE: This mode has been designed to be used when
watching movies.
GAME: This mode has been designed to be used when
watching home video game system.
ELEVELS
✔Picture adjustments (CONTRAST/
BRIGHTNESS/COLOUR/SHARPNESS/BACKLIGHT/
OPC)
Menu Operation: PICTURE Group A (top of this page)
Adjusts the picture to your preference with the following
picture settings.
1Press MENU to display the menu screen.
2Press c/dto select “PICTURE”.
Common Operation
Selecting an item from PICTURE Group A
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “LEVELS” or “ADVANCED”, and then
press OK.
• The “PICTURE LEVELS” menu screen can be
displayed directly by pressing Red.
3Press a/bto select the desired menu item (Example:
“PICTURE MODE”, “CONTRAST” etc).
4Press c/dto select/adjust.
✔PICTURE MODE
Menu Operation: PICTURE Group A (top of this page)
Select a predetermined picture level.
EADVANCED
The “ADVANCED” menu consists of the advanced feature
items for the picture adjustments.
NOTE
• “ADVANCED” items cannot be set when the FM radio mode is
selected.
✔COMB FILTER
Menu Operation: PICTURE Group A (left side of this page)
Set to “ON” to reduce the colour interference in picture with
fine details and the picture gets sharper.
NOTE
• When selecting RGB signal through EXT 1 terminal, “COMB
FILTER” is set to “OFF” automatically, for the best picture quality.
✔NOISE RED. (NOISE REDUCTION)
Menu Operation: PICTURE Group A (left side of this page)
Select your desired item from the three items of “OFF”,
“HIGH”, or “LOW” to reduce the noise when receiving a weak
signal. “NOISE RED.” provides high quality images with
minimal dot crawl and cross colour noise.
✔I/P SETUP
Menu Operation: PICTURE Group A (left side of this page)
Adjusting the image and input signal can give you a more
beautiful picture.
INTERLACE: Use this setting when you cannot get a clear
picture with PROGRESSIVE. (Especially suitable for media
with special effects like game software.)
PROGRESSIVE: Normally, you should select this setting.
✔MOV. COMP. (MOVEMENT COMPENSATION)
Menu Operation: PICTURE Group A (left side of this page)
The “MOV. COMP.” smoothes the quick jumps (movements)
of images on the screen, in order to avoid artifacts.
✔DYN. CONTRAST (DYNAMIC CONTRAST)
Menu Operation: PICTURE Group A (left side of this page)
Set to “ON” to increase the contrast on the soft parts of the
picture.
✔DYN. GAMMA (DYNAMIC GAMMA)
Menu Operation: PICTURE Group A (left side of this page)
Set to “ON” to increase the brightness on the dark parts of
the picture.
NOTE
•OPC: Select this mode to activate the Intelligent Picture Control.
This function allows the automatic adjustment of the screen
brightness, according to the ambient light of the room, via OPC
(Optical Picture Control).
When set to “ON”, make sure that no object obstructs the OPC
sensor, which could affect its ability to sense surrounding light.
Item cButton dButton
CONTRAST For less contrast For more contrast
BRIGHTNESS For less brightness For more brightness
COLOUR For less colour
intensity
For more colour
intensity
SHARPNESS For less sharpness For more sharpness
Item
Item
BACKLIGHT For screen dims For screen brightness
OPC Press c/dto select ON/OFF
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM10

11
Menu operations
✔MONOCHROME
Menu Operation: PICTURE Group A (page 10)
For viewing a video in monochrome.
✔COLOUR TEMP. (COLOUR TEMPERATURE)
Menu Operation: PICTURE Group A (page 10)
Adjusts the colour temperature to give the best white image.
Press c/dto add bluish/reddish tone to white images.
✔NTSC HUE
Menu Operation: PICTURE Group A (page 10)
Adjusts the skin colour during NTSC signal reception. Press
c/dto make skin tones become purplish/greenish.
SOUND menu
EUsing SOUND menu screen
1Press MENU to display the menu screen.
2Press c/dto select “SOUND”.
Common Operation
Selecting an item from SOUND Group A
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “EFFECTS”, and then press OK.
• The “SOUND EFFECTS” menu screen can be
displayed directly by pressing Virtual.
3Press c/dto select/adjust.
Selecting an item from SOUND Group B
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “LEVELS”, and then press OK.
3Press a/bto select “SPEAKERS“ or “EXTERNAL”, and
then press OK.
• The “SOUND SPEAKER LEVELS” menu screen can
be displayed directly by pressing Green.
4Press a/bto select the desired menu item (Example:
“VOLUME”, “BALANCE” etc).
5Press c/dto select/adjust.
Selecting an item from SOUND Group C
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “EQUALIZER”, and then press OK.
3EQUALIZER MODE: Press Red to select a pre-defined
equalization mode: “PERSONAL”, “CLASSIC”, “JAZZ”,
“POP”, “CONCERT” or “STADIUM”.
4To change the EQUALIZER MODE “PERSONAL”:
Press c/dto select 100Hz, 330Hz, 1KHz, 3.3KHz or
10KHz.
Press a/bto adjust the item to your desired position.
Selecting an item from SOUND Group D
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “STEREO”, and then press OK.
• The “SOUND STEREO” menu screen can be displayed
directly by pressing 2(Sound Mode Selector).
3Press a/bto select the desired menu item (Example:
“SPEAKERS”, “AV” or “SOUND IDENT.”).
4Press c/dto select/adjust.
BYPASS: Normal sound without sound effect.
DOLBY VIRTUAL: Divide the centre signal equally between the
left and right speakers to achieve a phantom centre image.
Process the mono surround channels (or left surround, right
surround) signal via a virtualised before sending it to the left,
right speakers, creating a virtualised image around the
listener.
PANORAMA: This sound reproduction mode mixes all four
surround decoder outputs to the left and right output channel
without any loss of information and creates a surround like
effect with only two speakers.
EEFFECTS
Select a predetermined sound effect.
ELEVELS
Adjusts the sound quality to suit your preference.
■VOLUME
Adjusts the volume. Press c/dto decrease/increase
volume.
✔SPEAKERS
Menu Operation: SOUND Group B (left side of this page)
✔SOUND EFFECTS
Menu Operation: SOUND Group A (left side of this page)
■AUTO VOL. (AUTO VOLUME)
Different sound sources, fairly often do not have the same
volume level, for example the changing from movie to the
advertisements. The Automatic Volume Correction (AUTO
VOL.) solves this problem and equalizes the volume levels.
■LOUDNESS
This setting increases the volume of low and high frequency
signals according to the current volume setting.
OFF: Deactivates the “LOUDNESS”.
NORMAL: Keeping the amplitude of the 1KHz reference
frequency constant.
SUPERBASS: Keeping the amplitude of the 2KHz reference
frequency constant.
■BALANCE
Adjusts the balance. Press c/dto increase volume of the
left/right.
Item
Item
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM11

12
Menu operations
✔EXTERNAL
Menu Operation: SOUND Group B (page 11)
Adjusts the sound level output to the external connectors to
suit your preference.
■SCART VOLUME
Adjusts the sound level output to the Euro-SCART connector
(EXT1). Press c/dto decrease/increase volume output.
■AV VOLUME
Adjusts the sound level output to the external connectors
(EXT2 and AV OUTPUT). Press c/dto decrease/increase
volume output.
ESTEREO
This enables the selection of the reception mode when
receiving a “STEREO” or “DUAL” (bilingual) signal. To let
you enjoy “STEREO” and “DUAL” broadcastings, this TV
receives stereo, bilingual, and monaural broadcasts.
NOTE
•About sound mode: In the “STEREO” menu you can select a
sound mode to the SPEAKERS and HEADPHONES, and another
to the audio output of the external connectors (EXT 2 and AV
OUTPUT).
• Depending on the sound transmission the sound reproduction
can be chosen in the “STEREO” menu as indicated below.
EEQUALIZER
Menu Operation: SOUND Group C (page 11)
This enables the selection of the pre-defined equalization
modes.
PERSONAL: User configurable mode. Five equalizer bands are
available.
CLASSIC: Predefined mode, designed to listen classic music
JAZZ: Predefined mode, designed to listen jazz music
POP: Predefined mode, designed to listen pop music
CONCERT: Predefined mode, designed to listen concert music
STADIUM: Predefined mode, designed to watch sports
✔SPEAKERS
Menu Operation: SOUND Group D (page 11)
Change sound mode. Select your desired mode to your
preference depending on the type of broadcast.
✔AV
Menu Operation: SOUND Group D (page 11)
Change sound mode in the audio output of the external
connectors. Select your desired mode to your preference
depending on the type of broadcast.
■DYNAMIC BASS
“DYNAMIC BASS” system extends the frequency range to
create different bass effects.
OFF: Deactivates the “DYNAMIC BASS”.
MEDIUM: Increases the volume of low frequency signals
moderately.
STRONG: Increases the volume of low frequency signals
exceptionally.
FEATURES menu
EUsing FEATURES menu screen
1Press MENU to display the menu screen.
2Press c/dto select “FEATURES”.
Common Operation
✔SOUND IDENT. (SOUND IDENTIFICATION)
Menu Operation: SOUND Group D (page 11)
Activates “ON” or deactivates “OFF” the automatic
identification of audio system of the current programme.
ON: The TV automatically identifies the received audio system
MONO (FM), STEREO or DUAL signal.
OFF: Disqualifies the automatic identification of the audio system
and forces the sound into MONO (FM).
This mode can be convenient when the level of the signal
received is extremely weak.
NOTE
• This function is independent for every programme.
Selecting an item from FEATURES Group A
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “TIMERS”, and then press OK.
• The “FEATURE TIMERS” menu screen can be
displayed directly by pressing TIMER.
3Press a/bto select the desired menu item (Example:
“DATE”, “TIME”, “ON TIMER”, “OFF TIMER”, “RADIO/TV”
or “VOL. LIMIT”).
4Press c/dto select/adjust or input 0–9.
Selecting an item from FEATURES Group B
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “AV-LINK”, and then press OK.
3Press a/bto select “AVL CONTROL”, and then press
OK.
4Press OK, Blue or Red to select the desired setting.
Exception: When you are watching the TV through the external
sources, the “STEREO” menu and 2(Sound Mode Selector) are
not operative. These operate only in TV mode.
Item
Item
Item
Signal Selectable item
STEREO STEREO, MONO
BILINGUAL DUAL CHANNEL A, B, AB, MONO
MONO NICAM MONO NICAM, MONO (FM)
MONO (FM) MONO (FM)
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM12

13
Menu operations
ETIMERS
You can set “DATE”, “TIME” (Clock), “ON TIMER” (Wake-up
timer) and “OFF TIMER” (Sleep timer) to automatically turn
on and off the TV or RADIO at the specified time.
You can also set “ON TIMER” to automatically turn on at the
specified sound volume.
The Timer functions that turn power on at the specified time
do not work unless the clock is adjusted. Be sure to adjust
the “DATE” and the “TIME” (Clock) first.
NOTE
• “DATE” and “TIME” are automatically set/corrected via the
Teletext broadcast when available.
• When you set “ON TIMER”, the WAKE-UP indicator lights up red
while in the Standby mode.
• “ON TIMER” and “OFF TIMER” will not be activated if the power
is turned off with a(Power) on the TV.
• In the event of a power cut, disconnection from the plug or TV
switch, all the data on the “ON TIMER” and “OFF TIMER” will be
cancelled.
• As a safety precaution, in the case of nobody being home when
the TV or RADIO switches on automatically, the TV will return to
Standby mode after 120 minutes; if it is to continue to run, any
button on the remote control functions should be pressed.
• The “OFF TIMER” data will be cancelled if you turn off the TV by
B(Standby/On) on the remote control unit.
• You can check the timer settings by pressing p(Display/ Info).
✔DATE
✔TIME
Menu Operation: FEATURES Group A (page 12)
Current date and current time are necessary to set in order
to be able to run the Timer functions.
Automatic adjustment: If a programme with Teletext is being
received, the “DATE” and “TIME” can be adjusted automatically
with that signal’s clock.
Press mto synchronize “DATE” and “TIME”.
• If a signal via satellite is being received, or if correct date or
time, cannot be obtained, “DATE” and “TIME” will have to be
adjusted manually.
Manual adjustment: Press the Programme select (0–9) to adjust
“DATE” (DD/MM/YY (day/month/year)) and “TIME” (HH:MM
(hour:minute)) manually.
Selecting an item from FEATURES Group C
1Select the programme you wish to record at the specified
time, using Programme select (0–9), Programmes List
(a/b)or P (r/s).
2Perform steps 1 and 2 in Common Operation.
3Press a/bto select “AV-LINK”, and then press OK.
4Press a/bto select “AVL TIMERS”, and then press OK.
5Press a/bto select the desired menu item (Example:
“DATE”, “START” etc).
6Press c/dto select/adjust or input 0–9.
Selecting an item from FEATURES Group D
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “CHILD LOCK”, and then press OK.
3Press a/bto select “LOCK ALL”, “LOCK PROGRAM”,
and then press OK.
4Input the desired four-digit “PIN” with 0–9, and then press
OK.
5Press a/bto select the desired menu item (Example:
“TYPE”, “START” etc).
6Press c/dto select/adjust or input 0–9.
Selecting an item from FEATURES Group E
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “CHILD LOCK”, and then press OK.
3Press a/bto select “CHANGE PIN”, and then press OK.
4Input your PIN with 0–9, and then press OK.
5Input new PIN with 0–9, and then press OK.
Selecting an item from FEATURES Group F
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “CHILD LOCK”, and then press OK.
3Press a/bto select “CLEAR LOCK”, and then press
OK .
4Input your PIN with 0–9, and then press OK.
✔ON TIMER (Wake-up timer)
Menu Operation: FEATURES Group A (page 12)
The “ON TIMER” turns on the TV or RADIO automatically
anytime of the day.
When “ON TIMER” has been set, press Bon the remote
control unit to put the TV into Standby mode.
When the preset time is reached, the TV or RADIO turns “ON”.
HH:MM (hour:minute)
IMPORTANT
• In order to use the “ON TIMER” (Wake-up timer), be sure to
deactivate all child protection beforehand, otherwise the “ON
TIMER” may not operate correctly. You may have to input your
PIN in the corresponding menu.
✔OFF TIMER (Sleep timer)
Menu Operation: FEATURES Group A (page 12)
The “OFF TIMER” switches the TV to Standby mode
automatically, after the set length of time has passed.
Input selectable item OFF, 30, 60, 90, or 120 (minutes)
✔RADIO/TV
Menu Operation: FEATURES Group A (page 12)
For the “ON TIMER” (Wake-up timer), you can select the
mode (TV or RADIO) to automatically turn on.
✔VOL. LIMIT (VOLUME LIMIT)
Menu Operation: FEATURES Group A (page 12)
For the “ON TIMER” (Wake-up timer), you can adjust the
sound volume when TV or RADIO automatically turns on.
EAV-LINK
This feature can only be used with NexTView, Smart Link,
Easy Link and Megalogic compatible VCR.
This “Intelligent” communication system allows controlling
some VCR functions from the TV and vice versa.
For example, it is possible to programme the VCR timer
recording from the TV or record the signal currently being
displayed on the TV regardless of the signal source.
In this case, the VCR and the TV must be connected through
the 21-pin Audio/Video connector especially available for
this function (EXT2 terminal in this TV) using the fully-wired
SCART cable.
Refer to your VCR operation manual for further information.
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM13

14
Menu operations
✔AVL TIMERS (AV-LINK TIMERS)
Menu Operation: FEATURES Group C (page 13)
In this menu you can set a late start and stop time for a
recording.
NOTE
• After input all functions (DATE, START, STOP, MODE and SPEED),
press OK to transfer the data to the external VCR.
■DATE
Set the recording date. DD/MM/YY (day/month/year)
■START
Set the time of recording beginning. HH:MM (hour:minute)
■STOP
Set the time of recording end. HH:MM (hour:minute)
■MODE
If you want to make additional recordings at the same time
each day, from Monday to Friday or weekly, select
“UNIQUE”, “MON-FRI” “DAILY” or “WEEKLY”.
NOTE
• “MODE” (UNIQUE/MON-FRI/DAILY/WEEKLY) can be changed
only if your VCR has these functions available.
■SPEED
Use this setting to change recording speed between “SP”
Standard-Play and “LP” Long-Play.
Standard-Play gives the best picture quality. Long-Play
provides the longest recording time.
NOTE
• “SPEED” (SP/LP) can be changed only if your VCR has these
functions available.
✔AVL CONTROL (AV-LINK CONTROL)
Menu Operation: FEATURES Group B (page 12)
Use this menu to “PRESET DOWNLOAD” and to “RECORD
WHAT YOU SEE”.
EDEMO
The “DEMO” (demonstration) function allows you to see all
the menus implemented in this TV.
Press END to stop the DEMO mode.
NONE: Cancels the protection.
ALWAYS: The access to the TV will be protected always.
TIMER: The access to the TV will be protected during the
programmed period. If you have set “TIMER”, it is
indispensable to set “START” and “STOP” period.
✔LOCK ALL
Menu Operation: FEATURES Group D (page 13)
Set the CHILD LOCK to the whole TV.
NOTE
•Access to protected modes: When the TV is protected in “LOCK
ALL” way, it will be blocked when switched on and the instruction
“INPUT YOUR PIN” will appear on the screen.
In order to view your TV, you must press 0–9 of your Secret
Number “PIN” and OK.
If the “PIN” is not entered, only a(Power) on the TV and B
(Standby/On) on the remote control unit will operate.
■TYPE
Set the desired period of time to lock the TV for.
■START
Enter the hour and minutes to set the beginning of protection.
HH:MM (hour:minute)
■STOP
Enter the hour and minutes to set the end of protection.
HH:MM (hour:minute)
ECHILD LOCK
Use the “CHILD LOCK” function to block access to the
television by means of a 4-digits code (PIN).
The protection can apply to the television itself “LOCK ALL”
or to specific programmes “LOCK PROGRAM”. With the
“CHILD LOCK” function, you can also programme a time
period during which the TV or the programmes will be
protected. (Your children cannot select the programme,
which you locked.)
IMPORTANT
• Refer to page 21 for “IMPORTANT NOTE ON DISENGAGING
ADVANCED CHILD LOCK”.
NOTE
• If the protection is timed, the blocking of the TV or programmes
will only occur during the time period programmed.
• In order for the timed protection to function correctly, the internal
clock must be set at the right time. To check the time setting,
see DATE and TIME on page 13.
✔LOCK PROGRAM
Menu Operation: FEATURES Group D (page 13)
Set the CHILD LOCK for individual programmes.
NOTE
•Access to protected modes: When one or several programmes
are protected, the TV will block any attempt to gain access to
them and the instruction “INPUT YOUR PIN” will appear on the
screen.
In order to view these programmes you must press 0–9 of your
Secret Number “PIN” and OK.
If the “PIN” is not entered, only P (r/s)for changing
programmes, a(Power) on the TV and B(Standby/On) on the
remote control unit will operate.
Item Button Description
PRESET
DOWNLOAD
OK Automatically transfers the
channel preset information
from the tuner on the TV to
the one on the connected
VCR via the EXT2 terminal.
START
RECORDING
Blue While the VCR is in Standby
mode, it automatically turns
on and starts recording the
image from the TV
(RECORD WHAT YOU
SEE).
STOP
RECORDING
Red The TV indicates the VCR
that must stop the
recording.
Item
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM14

15
NONE: Cancels the protection from the selected programme.
ALWAYS: The access to the selected programme will be
protected always.
TIMER: The access to the selected programme will be protected
during the programmed period. If you have set “TIMER”, it is
indispensable to set “START” and “STOP” period.
AUTO(VPS): Activates the automatic protection. The selected
programme will only be blocked when it receives the “VPS”
signal*.
■TYPE
Set the desired period of time to lock the TV for.
■PROGRAMME
Select the programme number you want to protect.
■START
■STOP
Refer to “START” and “STOP” in “LOCK ALL”. (See page
14.)
* When the programme that is being shown is not suitable for
children, some broadcasting stations send this “VPS” signal, for
activating the automatic protection.
✔CLEAR LOCK
Menu Operation: FEATURES Group F (page 13)
This option enables you to erase all the adjustments made
to the CHILD LOCK function except the PIN.
✔CHANGE PIN
Menu Operation: FEATURES Group E (page 13)
Set a new PIN.
Menu operations
SETUP menu
EUsing SETUP menu screen
1Press MENU to display the menu screen.
2Press c/dto select “SETUP”.
Selecting an item from SETUP Group A
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “AUTO INSTALLATION”, and then
press OK.
3Press c/dto select the desired language for the on-
screen display.
4Press bto select “SELECT COUNTRY”, and then press
c/dto select your country.
5Press OK to start Auto Channel Preset.
•You do not need to do anything during the Auto
Channel Preset.
6When the Auto Channel Preset is completed, the “EDIT”
menu screen displays.
Common Operation
Selecting an item from SETUP Group B
1Select the programme number you want to preset with
Programme select (0-9) or Programme List (a/b).
2Perform steps 1 and 2 in Common Operation.
3Press a/bto select, “MANUAL TUNE”, and then press
OK.
4Press a/bto select the desired menu item (Example:
“TYPE”, “SYSTEM” etc).
5Press c/dor Programme select (0-9) to select/adjust.
Selecting an item from SETUP Group C
1Perform steps 1 and 2 in Common Operation.
2Press a/bto select “EDIT”, “GENERAL SETUP”, “AV
SETUP”, “HDMI SETUP”, “DVI SETUP VIA HDMI” or
“POWER CONTROL” and then press OK.
3Press a/bto select the desired menu item.
4Press c/dto select/adjust.
EAUTO INSTALLATION
Menu Operation: SETUP Group A (left side of this page)
In this menu you can perform the Initial Auto Installation
again. Using this routine, you can select the On-Screen
Display “SELECT LANGUAGE”, set the “SELECT
COUNTRY”, and automatically search for and store all the
receivable TV and FM radio channels.
When the automatic search has been completed, the “EDIT”
menu (Stored Programmes) will appear on screen and you
can change the order of the channels, delete channels, and
change or give the channels an eight-letter name. (See page
8.)
EMANUAL TUNE
Perform the procedure to search for and store new TV
programmes after the first installation routine.
(e.g. when a new TV broadcasting station being installed
on your geographic area).
✔TYPE
Menu Operation: SETUP Group B (top of this page)
Select your desired item to your preference from the two
items of “AERIAL” or “CABLE”.
Item
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM15

16
Menu operations
✔MODE
Menu Operation: SETUP Group B (page 15)
This feature allows you to set the programmes to “TV”, “VCR”
or “SKIP” mode.
TV: If the TV signal is weak the image can shake. In this case
put it in TV mode.
VCR: In some cases, the upper part of the picture may be
distorted when receiving signal from a VCR via RF terminal
on the TV set. Selecting this option will help to reduce this
effect.
SKIP: Allows you to SKIP programmes you do not want to view
when using P (r/s). (Use Programme Select (0–9) or
Programmes list (a/b)to display these channels)
✔SYSTEM
Menu Operation: SETUP Group B (page 15)
For more information, see the table “Corresponding real
channel” on page 23.
✔CHANNEL
Menu Operation: SETUP Group B (page 15)
NOTE
• Receivable channels depend on TV norm (Band, System, etc.),
installation site, and range.
EEDIT
Menu Operation: SETUP Group C (page 15)
In this menu you can change the order of the channels,
delete channels, and change or give the channels an eight-
letter name. (See page 8.)
1Press c/dto select “TV” or “RADIO”.
2Press a/bto select the channel you want to edit, and
then press OK to watch/listen to TV/radio.
3Perform the steps below for each setting.
✔FINE TUNE
Menu Operation: SETUP Group B (page 15)
When a preset programme channel is not exactly tuned,
you can fine-tune the channel in this mode.
✔SCAN
Menu Operation: SETUP Group B (page 15)
NOTE
• Press and hold c/d, until the best tuning position is found, for
the best picture and sound, and then press OK to memorise.
Press c/dto “SCAN” between the existing channel and
the previous or next one.
• The tuning sequence will stop when a signal is detected.
• If the signal is not the required channel, press c/dto continue
searching.
• If the signal is the required channel, press OK to memorise.
For more information, see the table “Corresponding real
channel” on page 23.
✔EDIT
1Press Red to display the “EDIT” setting.
2Press a/bto change the letters, and then press c/d
for changing the position of the cursor.
3Press OK to “STORE” the name.
4Press END to exit.
NOTE
• The selected item is displayed in yellow letters with red
background.
• Letters A to Z of the alphabet, symbols, a blank space and the
numbers 0 to 9 will appear.
✔DELETE
1Press Yellow to display the “DELETE” setting.
2Press OK to delete the channel selected on the list.
3Press END to exit.
NOTE
• When you delete a channel, the channels that follow it on the list
will automatically rearrange themselves by moving up one
programme (Pr) place, to restore the space of the cancelled
channel.
✔SORT
1Press Blue to display the “SORT” setting.
2Press a/bto move the channel to the required position
(Pr).
3Press OK to “STORE”.
NOTE
• When you change of site a channel, the located channels next
are rearranged. By such reason, it is advisable to order the
channels, being begun by which you wish to place in the first
position (Pr1).
Item
Band System Real Channel Number
VHF L/L’ CH-02 — CH-10
B/G CH-02 — CH-20
I CH-01 — CH-09
D/K CH-02 — CH-12
UHF B/G, D/K, I,
L/L’
CH-21 — CH-69
CATV L/L’ CC-01 — CC-74
B/G CC-01 — CC-55
CH-75 — CH-79
I CC-01 — CC-68
D/K CC-01 — CC-41
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM16

17
Menu operations
✔TTX CHAR. SET (TELETEXT CHARACTER SET)
Menu Operation: SETUP Group C (page 15)
You can select a character set from the items listed on the
screen.
✔WSS (Wide Screen Signalling)
Menu Operation: SETUP Group C (page 15)
WSS allows a television to switch automatically among the
different screen formats.
Select “ON” to activate the “AUTO” function, located in the
“WIDE MODES” menu screen. (See page 20.)
✔ROTATION
Menu Operation: SETUP Group C (page 15)
You can set the orientation of the picture by this function.
ABC
ABC
ABC ABC
[NORMAL] [MIRROR] [UPSIDE
DOWN]
[ROTATE]
EAV SETUP
Menu Operation: SETUP Group C (page 15)
In this menu, you can configure the input terminals in
concordance with the connected device and the signal type.
The EXT 5 terminals is only necessary for setting the “HDMI
SETUP” or “DVI SETUP VIA HDMI”.
✔OSD LANGUAGE
Menu Operation: SETUP Group C (page 15)
You can select a language from setup menu. Select from
among 13 languages: DUTCH, ENGLISH, FINNISH,
FRENCH, GERMAN, GREEK, ITALIAN, POLISH,
PORTUGUESE, RUSSIAN, SPANISH, SWEDISH, TURKISH.
EGENERAL SETUP
The “GENERAL SETUP” menu consists of the generally used
setting items.
✔ FACTORY SETTINGS
Menu Operation: SETUP Group C (page 15)
Press OK to set the factory presets.
Selectable item
RGB/
YCbCr 4:4:4/
YCbCr 4:2:2
ITU601/
ITU709
STANDARD/
ENHANCED
ENABLE/
DISABLE
DIGITAL/
ANALOGUE
Item
SIGNAL
TYPE
COLOUR
MATRIX
DYNAMIC
RANGE
AUTO
VIEW*
AUDIO
SELECT*
Description
Select the signal type from
the HDMI terminal.
Select the internal colour
space conversion method
when RGB signal is input.
Select the signal
amplitude range. Usually,
select “STANDARD”.
Set whether or not to use
WIDE MODE based on
signal recognition,
including HDMI signal.
Select “DIGITAL” for audio
signal via the HDMI
terminal. Select
“ANALOGUE” for audio
signal via the AUDIO jack.
NOTE
• Items marked with * are available in HDMI SETUP. All items are
available in DVI SETUP VIA HDMI except “AUDIO SELECT”.
EHDMI SETUP
EDVI SETUP VIA HDMI
Menu Operation: SETUP Group C (page 15)
HDMI (High-Definition Multimedia Interface) terminal
selection.
Input terminal Type
EXT 1 SOURCE VCR, DVD, AUTO
EXT 2 SOURCE VCR, DVD, AUTO
EXT 3 SIGNAL CVBS, Y/C
EXT 4 SIGNAL SD, HD, AUTO
SOURCE Description
VCR For viewing the signals from a Video
Cassette Recorder equipment through the
selected input terminal.
DVD
AUTO
EXT 2 SIGNAL CVBS, Y/C
For viewing the signals from a Digital Video/
Versatile Disc equipment through the
selected input terminal.
For auto detection of the input signal type.
EXT 1 SIGNAL CVBS, Y/C, RGB
EXT 3 SOURCE VCR, DVD, AUTO
SIGNAL
CVBS
Y/C
RGB
HD (High
Definition)
SD (Standard
Definition)
AUTO
Description
For viewing COMPOSITE VIDEO signal
output from video equipment.
For viewing S-VIDEO signal output from
video equipment.
For viewing RGB signal output from video
equipment.
For viewing the signals from video
equipment, with output COMPONENT of
Standard Definition, connected through the
EXT4 terminals.
For viewing the signals from video
equipment, with output COMPONENT of
High Definition, connected through the EXT4
terminals.
For auto detection (HD or SD) of EXT 4
terminals.
LC-26/32/37GA6E(E)_b 05.6.29, 7:50 AM17

18
PC INPUT mode adjustments
TitleB
Menu operations
EPICTURE/SOUND adjustments
After connecting the PC to your TV (see page 7), you can
adjust the “PICTURE” and “SOUND” modes to your
preference setting with the following steps.
1Press bon the remote control unit to display the
“EXT. SOURCES MENU” screen.
2Press a/bto select “PC INPUT”, and then press OK
to display PC image on your TV.
3For PICTURE setting:
Press MENU or Red to display PICTURE setting.
1Press a/bto select your desired PICTURE item.
(CONTRAST/BRIGHTNESS/PHASE/CLOCK)
2Press c/dto adjust the item to your desired position.
3Press END to exit.
For SOUND setting:
Press Green to display SOUND setting.
1Press a/bto select your desired SOUND item.
(VOLUME/BALANCE/LOUDNESS/DYNAMIC BASS/
MODE)
2Press c/dto adjust your desired position or select your
desired item.
3Press END to exit.
EImage position
After connecting the PC to your TV (see page 7), you can
adjust a picture’s horizontal or vertical position with the
following steps.
1Perform steps 1 to 2 in PICTURE/SOUND
adjustments.
2Press a/b/c/dto centre the image by moving to
H.POS/V.POS.
Resolution Vertical Frequency 60Hz
O
O
O
O
O
O
O
O
O
640 g400
720 g400
640 g480
848 g480
800 g600
1024 g768
1280 g720
1280 g768
1280 g1024
VGA
WVGA
SVGA
XGA
WXGA
SXGA
EPC compatibility chart
✔POWER MANAGEMENT
Menu Operation: SETUP Group C (page 15)
When set to “ON”, the power will automatically shut down
(Standby mode) if no image signal is received from the PC
in the PC input mode.
EPOWER CONTROL
Power control setting allows you to save energy.
✔NO SIGNAL OFF
Menu Operation: SETUP Group C (page 15)
When set to “ON”, the power will automatically shut down if
no signal inputs for 15 minutes.
✔NO OPERATION OFF
Menu Operation: SETUP Group C (page 15)
When set to “ON”, the power will automatically shut down if
no operation for 3 hours.
Useful adjustment settings and features
LC-26/32/37GA6E(E)_c 05.6.29, 7:50 AM18