Sharp AN-WS350 User manual

RACK SOPORTE DE PIE
WALL ASIDE STAND
AN-WS350
AN-WS350R
MODELO
MODEL
Please refer to pages E-1 to E-14.
ENGLISH
Consulte las páginas S-1 a S-14
ESPAÑOL
MANUAL DE MANEJO
OPERATION MANUAL
...
AN-WS350_OM_FRONT.indd 1 2009-08-15 10:37:50

E-1
ENGLISH
Thank you for purchasing this SHARP product. Before using the product, please be sure to
read this operation manual carefully. In particular, be sure to read the section “To Ensure
Safe and Correct Use”. After reading the manual, keep it in a convenient location where it
can be accessed at any time.
Parts
Please conrm that the following parts are included.
WU V
METAL BASE x 1 LCD TV
SUPPORT (A) x 2
LCD TV
SUPPORT (B) x 2
LCD
U BRACKET x 1
CENTRE BAR x 1 LCD TV HOOK
x 2
SOUND BAR
SUPPORT x 1
SOUND BAR U
BRACKET x 1
SUPPORT
PLATE x 1
SCREWS
M8 [50mm] x 4
ALLEN KEY M6
x 1
ALLEN KEY M8
x 1
SOUND BAR
SPACER x 8
GLASS SHELF
SUPPORT
TV SPACER
x 4
SCREWS
M8 [16mm] x 4
SCREWS
M6 [35mm] x 6
SCREWS
M6 [16mm] x 53
SCREWS
M4 [12 mm] x 6
FLANGE
NUT x 20
SPRING
WASHER
Ø6 x 4
SPRING
WASHER
Ø8 x 8
GLASS x 2 CABLE COVER
x 1
BACK COVER
x 1 CABLE BAND x 2
LEFT x 2
RIGHT x 2
4 mm 5 mm
GLASS PROTECTOR x 4
SCREWS
M6 [45mm] x 4
SCREWS
M8 [45mm] x 4
AN-WS350_OM_EN.indd 1 2009-08-19 23:00:03

E-2
EN
To Ensure Safe and Correct Use
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays
and labels and incorrectly using the product could have results as classied below. Please read the following warning
symbol information before reading the rest of this section, and be sure to strictly observe all instructions.
Warning: Not following these instructions could result in death or serious injury.
Caution: Not following these instructions could result in injury or property damage.
Meaning of symbol The symbol means something that should not be done.
Special Precautions for Safety
Warning:
zFollow the instructions in this manual regarding the installation method and installation orientation. Not following
these instructions could result in injury or damage from falling parts.
zAccurate work is required for the installation work, so please have it done by the dealer or qualied contractor.
zDuring installation, be careful not to pinch your ngers in the xture, etc.
zDo not apply any other loads to the installation xtures. Doing so could cause the TV to fall causing injury and
damage.
zDo not modify or change the installation parts. Doing so could cause the TV or sound bar system to fall causing
injury and damage.
zBe sure to install the stand on a solid and level oor. When assembling, lay the packing material on the oor to
avoid damage to the oor.
zDo not use a stand if it has sustained any cracks.
zDo not climb on the stand and do not use the stand as a footstool.
zDo not move the stand with the TV attached or with connected equipment inside.
zWhen using an electric screwdriver, set the torque setting to approximately 2.0 N-m (20 kgf-cm).
zThis unit is suitable for SHARP LCD TV with sizes ranging from 32” to 46”.
zDo not use chemicals for cleaning (petrol, paint thinner, etc.). It may damage the cabinet nish. Periodically wipe
it with a soft cloth.
zDo not let children play around the TV stand as this might cause injury or the stand might fall on them.
zDo not step, stand or sit on the glass shelf.
zMaximum load on the glass shelf is 10 kg.
Caution:
Install in a location with low humidity and little dust. Install in a well-ventilated area.
zDo not install the LCD colour TV in a location
with high humidity and much dust. Doing so
could result in re or electric shock.
zDo not place the LCD colour TV where it will
come into contact with oily smoke or steam,
such as near a cooking range or humidi-
er. Doing so could result in re or electric
shock.
zDo not plug the air passage holes in the LCD
colour TV cabinet. Plugging the air passage
holes could trap heat inside the cabinet,
causing a re.
zDo not use the cabinet as follows. Do not
place the cabinet in a place with poor air cir-
culation, such as in a closet or bookcase. Do
not place a drop cloth, etc., on the installed
LCD colour TV.
Please strictly observe the following.
Special skill is required to install the LCD colour TV and Wall Aside Stand, so please have them installed by a
contractor specializing in such installation. The customer should not attempt to install the TV. Sharp shall not be
responsible for improper installation or any accidents, damage, or injury resulting from improper installation.
AN-WS350_OM_EN.indd 2 2009-08-19 23:00:05

E-3
Assembling the Centre Bar and Metal Base
Note:
Installation of this unit requires 2 or more
persons.
P
Kx 2
G
Step 1
Screw the Support Plate (G) to the Metal
Base with 2 pieces of M6 [16mm] screws
(K) rst, using the M6 Allen key (P).
Step 2
Flip the Metal Base upside down. You can
see the “SHARP” logo is facing upwards.
AN-WS350_OM_EN.indd 3 2009-08-19 23:00:05

E-4
EN
Step 3
Place the Centre Bar next to the Metal Base, on top of the
Support Plate (G).
Step 4
From under the Metal Base, place 4 pieces of M8 [50mm]
screws (H) with Spring Washers Ø8 (O).
Step 5
Slowly lift the xture upwards and let it stand on the
oor.
Side view
Ensure that the specication label
is facing the oor when combining
the Centre Bar and Metal Base.
The screws should be tightened using Allen key M8 (Q)
according to the sequence A →B → C →D as shown
above.
AN-WS350_OM_EN.indd 4 2009-08-19 23:00:06

E-5
Assembling the Centre Bar and Metal Base (continued)
Step 6
Fasten another 4 pieces of M6 [16 mm]
screws (K) using M6 Allen key (P) to the
Support plate as shown.
Step 7
Before peeling off the masking tape securing the legs, hold the
legs rmly and be careful not to be hit by them. After peeling off
the tape, release the leg slowly until it fully opens out.
Be careful not to pinch your ngers
in the xtures.
Caution:
Note:
When pushing the stand against the
wall, the legs will bend inwards.
Note:
This product is designed to be located
against the wall. However, if the user
wishes to locate it further away from
the wall or at the centre of a room,
do ensure that the unit’s legs are fully
opened.
Specication label
Assembling the LCD Support Frame
Step 1
Fix the LCD Support Bar (A) with LCD U Bracket (C) using 4
pieces of M6 [16mm] screws (K) and 4 pieces of Flange Nuts
(M). Use M6 Allen key (P) to fasten the screws.
AN-WS350_OM_EN.indd 5 2009-08-19 23:00:12

E-6
EN
Step 2
Slot in the LCD support frame to the Centre Bar as
shown.
Step 3
Fix the LCD Support Bar (A) with LCD U Bracket
(C) using 4 pieces of M6 [16mm] screws (K) and 4
pieces of Flange Nuts (M). Use M6 Allen key (P) to
fasten the screws.
Step 4
Fix the LCD Support Bar (B) using 8 pieces of M6
[16mm] screws (K) and 8 pieces of Flange Nuts
(M) as shown. Use M6 Allen key (P) to fasten the
screws.
Step 5
Screw the Support Frame to the Centre Bar using 6
pieces of M6 [16mm] screws (K). Fasten them with
M6 Allen key (P).
Do not hold the Support Frame at the
centre while inserting it to the Centre
Bar as this will cause injury.
Caution:
AN-WS350_OM_EN.indd 6 2009-08-19 23:01:04

E-7
Assembling the LCD Support Frame (continued)
Notes:
zThe LCD Support Bar is adjustable to different heights.
Maximum height is 1250 mm. Minimum height is 1030 mm.
zWhen xing the frame, make sure that all the 6 pieces of M6
[16mm] screws are fastened to it.
zIf adjusting to maximum height, make sure that you
do not exceed the stopper.
zWhen xing the frame to maximum height, make
sure that all the 6 pieces of M6 [16mm] screws are
fastened to it.
Stopper
Caution:
Minimum height = 1030 mm
Maximum height = 1250 mm
AN-WS350_OM_EN.indd 7 2009-08-19 23:01:26

E-8
EN
Assembling the glass shelf
Falling prevention (optional)
Fix the safety wire or
chain to the wall using
a wall anchor bracket
which is commercially
available.
It is recommended to secure the xture to the
wall with a safety wire or chain before attach-
ing the TV to prevent it from toppling over in
case of earthquake occurrence.
Screw
Washer
Safety wire
(commercially
available)
surface
Step 1
Fix the left (S) and right (T) Glass Shelf Supports to the Centre
Bar using 4 pieces of M6 [16mm] screws (K) as shown. Fas-
ten them with Allen key M6 (P).
Step 2
Remove the transparent glass protective sheet at the bottom
surface of the glass. Top surface has a label afxed on it.
Peel off the separator of the double sided tape on the Glass
Protectors. Slot in 2 pieces of Glass Protector at the corners
of the glass as shown below.
Step 3
Peel off the separator of the double sided tape on the
left and right Glass Shelf Supports.
Double sided tape
Double
sided
tape
Label
Top surface
Glass protective
sheet
AN-WS350_OM_EN.indd 8 2009-08-19 23:01:34

E-9
Assembling the glass shelf (continued)
Step 4
Place the glass on the Glass Shelf Supports as shown.
Make sure all the Glass Protector guides are inserted
perfectly into the holes of the left and right Glass Shelf
Supports.
Notes:
zThe glass is made of reinforced glass, but dropping
pointed objects on it or strongly hitting the surface may
cause it to break.
zThe glass shelf is not fastened to the unit. Avoid han-
dling the glass when transporting the unit, otherwise it
may fall off and there is a risk of damage and injury.
Hole
Glass protector
guide
Assembling the Sound bar Support (optional)
Step 1
Fix the wall mount angle (comes with Sound bar
unit) to the Sound bar Support (E) using 4 pieces
of M4 [12mm] screws (L). Fasten them with a “+”
screw driver.
Step 2
Screw the Sound bar Support (E) to the Sound bar U Bracket
(F) using 4 pieces of M6 [35mm] screws (J) with 4 pieces of
Flange Nuts (M). Insert 8 pieces of Sound bar Spacers (R) as
shown below. Fasten them with M6 Allen key (P).
Notes:
You can omit the Sound bar Spacers (R) if you like but when
you do this, make sure that the screw type is changed from
M6 [35mm] (J) to M6 [16mm] (K)
You can include your Sound bar system to this unit to enhance the sound of your LCD TV.
R
WALL MOUNT ANGLE
(not supplied)
Label
AN-WS350_OM_EN.indd 9 2009-08-19 23:01:37