SHC SL19 User manual
1
Model SL19 Installation Manual
Staying Home Corporation
--
2
Preliminary Checks
Installation Site Requirements
_____ -
_____
_____
Included with Shipment
_____
____ -
_____
____
_____
_____
_____ 6’
_____
_____
____
_____
_____
_____
Tools Required
_____
_____
_____
_____
_____
_____
_____
_____(7/16” & 1/2")
_____
3
Typical Components
4
Underside of Chassis
5
Identify Track Pieces
-
6
Installation Procedures for Stock Units
Track Installation: Track and rack should be cut before installing them on the staircase
-
--
-
Note: The gear rack is already
inserted in the gear rack channel of the track.
7” (note: be sure to verify clearance from
top nose to any obstruction at the top such as a door or door
frame that would cause the chair to hit or block the seat from
swiveling.)
7
.
Left Hand
Installation
Right Hand
Installation
8
Splice Track Pieces Together
-
.
9
Secure the Track to the Stair Treads
10
Insert the Chassis into the Track
One shim goes onto
each axle on the gear rack side only.
Failure to have the proper shims in place will
cause the pinion gear not to engage in the gear
rack properly.
11
-
-
12
13
Note that the ETL
listing is valid only when the track installed at maxi-
mum angle of 45°.
-
-
14
15
RF Remote Call-Send Controls
A
RF Receiver #74033
Key Fob Transmitter
#74034
16
AUDIO/VISUAL STATUS INDICATIONS
-
STATUS LIGHT AUDIBLE ALARM CONDITION
-- -
-
17
Completion Procedures SERVICE LINE 877.378.4275
(Mon-Fri 8:00 – 5:00 CST)
Completion Checklist
_______ Upper and lower limits:
_______ Charger:
_______ Running Clearance:
_______ Unit Control:
_______ Call/Send Remotes:
Track:
_______ Important:Top Track End Plate:
_______ Important:Lower Track End Plate:
_______ Track Mounting Brackets:
_______ Track Splice:
_______
_______
_______ Verify the gear rack is lubricated with lithium or other all-purpose grease
_______
_______
Footrest:
_______
_______
_______
_______
_______
Seat:
_______
_______
_______
_______
_______
_______
_______ Clean Up:
Before leaving the jobsite:
_______
_______
_______
_______
N.O .
N.O .
24V
RF RX
N.C.
N.O.
DIAGNOSTIC LED
- SOLID GREEN - ALL SYSTEMS NORMAL
- AMBER BLINK - 1/4 SECOND BEEP FOR 10 MINUTES, BATTERIES NOT BEING CHARGED
- AMBER PULSING - LOW BATTERY VOLTAGE
- 2 AMBER FLASHES - SEAT SWIVEL LATCH SENSOR
- AMBER FLASHES - FOOTREST OBSTRUCTION UPHILL
- 2 RED FLASHES - TWO OR MORE SAFETY CIRCUITS OPEN
- RED FLASHES - FINAL LIMIT CIRCUIT OPEN
- 4 RED FLASHES - TRAVEL TIMEOUT
- 5 RED FLASHES - OVERSPEED DEVICE
- SOLID AMBER - OVERLOAD
- SOLID RED - KEY SWITCH TURNED OFF DURING TRAVEL
BLUE
SWIVEL SEAT
GRAY
KEY SWITCH
BLACK
BROWN
GRAY
STATUS
LIGHT
YELLOW
YELLOW
RED
YELLOW
BLUE
BLUE
4
2
1
4
2
1
1
2
4
1
2
4
5
6
7
8
9
10
11
12
1
14
15
16
17
18
19
20
21
22
2
24
25
26
27
28
29
0
WIRING DIAGRAM - SL19
BLUE
BLUE
YELLOW
YELLOW
YELLOW
BLUE
RED
RED
RED
BLUE
BLUE
GREEN
GREEN
DN
UP
JB
INSTALL CONTROL
DN LIMIT
UP LIMIT
FINAL LIMIT
UP FOOTREST
RED
CONTROLLER
15AMP
WHITE
12VDC
- +
12VDC
- +
120VAC
24VDC
2AMP
BRAKE
24VDC
MOTOR
BLACK
B
K
1
B
K
2
CHG
M
2
M
1
B
+
B
-
REVISIONS
REV. DESCRIPTION DATE BY
A RELEASE 10/24/2018 JB
ORG
ORG
OVERSPEED
0-PIN CONN
UP
DN
SEAT CONTROL
STAYING HOME CORPORATION IS
D
C
B
A
A
B
C
D
24
5
678
876542
DRAWING IS THE SOLE PROPERTY OF
REPRODUCTION IN PART OR AS A WHOLE
0.005
5410
SHEET 1 OF 1
10/24/18
WITHOUT THE WRITTEN PERMISSION OF
PROHIBITED.
THE INFORMATION CONTAINED IN THIS
DO NOT SCALE DRAWING
B
INTERPRET GEOMETRIC
THREE PLACE DECIMAL
SIZE
0.01
1
A
TITLE:
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:1
NAME
WEIGHT:
REV
DATE
DWG. NO.
STAYING HOME CORPOTATION. ANY
PROPRIETARY AND CONFIDENTIAL TOLERANCING PER:
MATERIAL
FINISH
DRAWN
CHECKED
ENG APPR.
MFG APPR.
Q.A.
COMMENTS:
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL 1/16
ANGULAR: 0.5
°
ONE PLACE DECIMAL 0.1
TWO PLACE DECIMAL
Staying Home Corporation
2501 Anaconda Rd
Harrisonville, MO 64701
816-380-2427
www.stayinghome.com
Table of contents
