Shinko DSW-100-H Service manual

1
Installation Instruction Manual Indoor Humidity Sensor DSW-100-H
No.DSW12JE5 2019.10
Preface
Thank you for purchasing our DSW-100-H, Indoor Humidity Sensor.
This manual contains instructions for installation and handling of the DSW-100-H. To ensure safe and correct
use, thoroughly read and understand this manual before using this sensor. To prevent accidents arising from
the misuse of this sensor, please ensure the operator receives this manual.
Notes
• This sensor should be used in accordance with the specifications described in the manual. If it is not used
according to the specifications, it may malfunction or cause a fire.
• Be sure to follow all of the warnings, cautions and notices. If they are not observed, serious injury or
malfunction may occur.
• The contents of this instruction manual are subject to change without notice.
• Care has been taken to ensure that the contents of this instruction manual are correct, but if there are any
doubts, mistakes or questions, please inform our sales department.
• Any unauthorized transfer or copying of this document, in part or in whole, is prohibited.
• Shinko Technos Co., Ltd. is not liable for any damage or secondary damage(s) incurred as a result of using
this product, including any indirect damage.
Safety Precautions (Be sure to read these precautions before using our products.)
The safety precautions are classified into 2 categories: “Warning” and “Caution”.
Depending on the circumstances, procedures indicated by Caution result in serious consequences, so be
sure to follow the directions for usage.
Warning
Procedures which may lead to dangerous conditions and cause death or serious injury, if not carried
out properly.
Caution
Procedures which may lead to dangerous conditions and cause superficial to medium injury or physical
damage or may degrade or damage the product, if not carried out properly.
Warning
• To prevent an electrical shock or fire, only Shinko or other qualified service personnel may handle the
inner assembly.
• To p revent an electrical shock, fire or damage to the instrument, parts replacement may only be
undertaken by Shinko or other qualified service personnel.
SAFETY PRECAUTIONS
• To ensure safe and correct use, thoroughly read and understand this manual before using this
instrument.
• This instrument is intended to be used for general equipment. Verify correct usage after purpose-of-use
consultation with our agency or main office.
(Never use this instrument for medical purposes with which human lives are involved.)
• External protection devices must be installed, as malfunction of this product could result in serious
damage to the system or injury to personnel. Proper periodic maintenance is also required.
• This instrument must be used under the conditions and environment described in this manual.
Shinko Technos Co., Ltd. does not accept liability for any injury, loss of life or damage occurring due to
the instrument being used under conditions not otherwise stated in this manual.
Caution with Respect to Export Trade Control Ordinance
To avoid this instrument from being used as a component in, or as being utilized in the manufacture of
weapons of mass destruction (i.e. military applications, military equipment, etc.), please investigate the
end users and the final use of this instrument.
In the case of resale, ensure that this instrument is not illegally exported.
和文は裏面をご覧ください。

2
1. Model
1.1 Model
Model
Measurement Range
Output
DSW-100-H
5 to 90 %RH
4 to 20 mA DC 2-wire type
DSW-100-H W4
4 to 20 mA DC 4-wire type
DSW-100-HV W4
0 to 1 V DC 4-wire type
1.2 How to Read the Model Label
Model label is attached to the inside of the case.
1
Model
2
Measurement range, Output
3
Power supply voltage, Power consumption
4
Serial number
(Fig. 1.2-1)
2. Mounting
Caution
Installation site should be examined, giving careful consideration to the following conditions.
This sensor is designed for indoor use only. Do not install outside.
[This instrument is intended to be used under the following environmental conditions.]
• Free air flow
• A minimum of dust, and an absence of corrosive gases
• No flammable, explosive gases
• No mechanical vibrations or shocks
• No exposure to direct sunlight, an ambient temperature of 0 to 50 (32 to 122 ) that does not
change rapidly, and no icing
• An ambient non-condensing humidity of 5 to 90 %RH
• An absence of chlorinated and sulfidizing gases
• No large capacity electromagnetic switches or cables through which large current is flowing
• No water, oil, chemicals or the vapors of these substances can come into direct contact with the unit.
Inquiries
For any inquiries about this unit, please contact our agency or the vendor where you purchased the
unit after checking the model and serial number. Please let us know the details of the malfunction, or
discrepancy, and the operating conditions.
SHINKO TECHNOS CO., LTD.
OVERSEAS DIVISION
:Head Office
URL:
E-mail:
2-5-1, Senbahigashi, Minoo, Osaka, Japan
http://www.shinko-technos.co.jp/e/
[email protected]
Tel :
Fax:
[phone]
[phone]
4
3
2
1

3
(2) Wiring
Connect the main unit lead wire to
the wire from the wall side.
(A)
(A)
(B) (B)
(C)
(C)
(C)
Mounting Plate
Main Unit
Main Unit Cover
(C)
3. Wiring
DSW-100-H DSW-100-H W4, DSW-100-HV W4
(Fig. 3-1) (Fig. 3-2)
Lead Wire Color
Lead Wire Type
ORG: Orange
+
4 to 20 mA DC or
0 to 1 V DC
YLW: Yellow
-
BRW: Brown
+
Power supply
BLK: Black
-
4. Replacing Humidity Sensor (HD-S2)
Follow the procedure below to replace the humidity sensor (HD-S2).
(1) Turn the power to the unit OFF, then remove the cover of the main unit.
(2) Pull the humidity sensor (HD-S2) out from the socket.
(3) Insert the new humidity sensor (HD-S2), with the model label facing
downward.
[NOTE]
As the humidity sensor (HD-S2) is polarity sensitive, so be sure to
insert the sensor correctly, otherwise the sensor will be broken,
and measurement will be impossible.
Never disassemble the humidity sensor as it may lead to
malfunction.
(4) Mount the main unit cover, then turn the power to the unit ON.
Socket
H
umidity sensor (HD-S2)
(3) Mounting Main Unit
Screw 4 places (C) as indicated by the dotted lines,
and fix the sensor main unit to the Mounting Plate.
For screws, use M3 screw (4 pieces) provided.
(4) Fitting Main Unit Cover
Insert the main unit cover protrusion (2 places) into
the cover mounting holes (2 places) located on the
upper part of the sensor main unit, then fit the cover
to the sensor main unit.
(1) Fixing the Mounting Plate
Screw either (A) or (B), and fix the Mounting Plate
to the outlet box, via outlet box cover located
inside the wall.
For screws, use M4 screw (2 pieces) and spring
washer provided.

4
5. Specifications
Measurement Range
5 to 90 %RH
Output
4 to 20 mA DC
(Linear conversion corresponding to
0 to 100 %RH)
2-wire or 4-wire type (Selectable)
Maximum allowable load: 500 max.
0 to 1 V DC
(Linear conversion corresponding to
0 to 100 %RH)
4-wire type only
Maximum allowable load: 500 max.
Power Supply Voltage
24 V DC 10%
Element Type
Electrostatic capacity change-type
Mounting
To the outlet box (inside wall), via outlet box cover. Mounting dimension: 66.7 mm
(JIS-C8340: 1999) (JIS: Japan Industrial Standards.)
Material
Flame-resistant PC resin, Color: White
Wiring
Lead wire: 300 mm Cross-section area: 0.5 mm2See “3. Wiring” for details.
External Dimensions
W90 x H90 x D32 mm (excluding lead wire)
Weight
Approx. 90 g
Performance
Accuracy
5 %RH (at 5 to 45 )
Out of range 5 to 45 : Max. 8 %RH
Under the conditions of:
Input power supply: 24 V, Load resistance: 250 ,
Wind velocity: 0.15 m/s, Warm-up period: 60 minutes
The output accuracy will be affected if the conditions above are
changed.
Response
characteristics
Approx. 20 seconds [Time to reach 90% of the RH value when the
RH shifts between 30 85 %RH. However, airflow 5 l/min (0.16 m/s)]
(Waterproof filter attached)
Hysteresis: Approx. 0 %RH (Stabilization time: 20 minutes)
Power Consumption
Approx. 550 mW (2-wire type) Approx. 3 W (4-wire type)
Operating
Environment
Temperature: 0 to 50 Humidity: 5 to 90 %RH (non-condensing)
[Caution]
Do not use this sensor in an environment where dew condensation occurs.
Do not use this sensor in an environment where chlorinated and sulfidizing
gases are being generated.
Storage Environment
Temperature: -20 to 60 Humidity: 5 to 90 %RH (non-condensing)
Insulation Resistance
Between Case - Output: 500 M minimum, at 500 V DC
Dielectric Strength
Between Case - Output: 1.5 kV for 1 minute, 3 mA max.
Accessories
Mounting plate, Mounting plate screw: M4 x 8 (2 pieces), Spring washer (2 pieces )
Sensor main unit mounting screw: M3 x 4 (4 pieces), Instruction manual: 1 copy
Environmental Spec
RoHS directive compliant