SHOP INDOOR GOLF DIY Golf Simulator Enclosure Owner's manual

4

Thank You!
Thank you for your purchase of a golf
simulator impact screen and enclosure kit!
In this guide, you will find everything you need
to complete the assembly of your kit and a
few helpful tips to ensure you have the best
indoor golf experience.

Z
Table of Contents
SPECIFICATIONS & SAFETY.............................................................................. 1
WHAT’S INCLUDED........................................................................................... 2
OVERVIEW OF SIG ENCLOSURE....................................................................... 2
WHAT’S NOT INCLUDED .................................................................................. 3
FRAME ASSEMBLY............................................................................................ 5
ENCLOSURE ASSEMBLY ................................................................................... 8
GOLF IMPACT SCREEN CARE & USE .............................................................. 11

Specifications
Pease make sure to take proper safety precautions and keep children, pets, and spectators out of swing
range.
Additionally, take every precaution to protect ceilings, walls, windows, cars, and neighboring homes.
Be alert of where you stand or walk and stay out of someone’s swing path
Make sure the setup is far from gas, electric heater, fireplace, candles, or any other similar source of heat.
When not in use, store neatly in a cool dry location, protected from sunlight
We are not responsible for damage to property &/or personal injury.
Be mindful of potential falling pipe if not tightened properly.
Do not hang from the enclosure.
Safety Instructions
1

What’s Included
(1)Nylon Enclosure Surround (2) Side Barriers
(1)SIGPRO Premium Impact Screen (2) Sand Bags
(2)Bundles of Bungees (6” ball bungees) (14) Canopy Fittings
(1)Weighted Bag Attachment
Enclosure Overview
2

What’s Not Included
Pipe Frame
(14) 10 Foot EMT Pipe *Cut Sizes for Pipe*
-(6) 1” EMT Pipe at 71”
-(4) 1” EMT Pipe at 56 3/8”
-(4) 1” EMT Pipe at 110”
Tools Needed
-Ladder
-Wrench/ Socket Set
-Pipe Cutter (Chop Saw)
-Tape Measure
3

Enclosure Diagram Page
4

Frame Assembly
Note: Insert Pipes fully into canopy fitting connectors and then tighten the hex bolts with a
wrench or socket wrench. This step will be repeated throughout the Frame Assembly
Portion of this manual.
Step 1
Attach (2) 71” pipe in the center with a straight connector and attach (2) 3-way connectors
on each end.
Step 2
Now insert (2) 56 3/8” pipe into the left and right side of the frame at the bottom.
Step 3
Connect FL elbow to the left and right of the frame as shown in the image below:
56 3/8” Pipe
L Connector
56 3/8” Pipe
71” Pipes
3 Way
3 Way
5
Straight Connector
L Connector

Step 4
Connect the 110” pipe vertically to the all four sides of the frame as shown in the image
below
110 ” Pipe
Frame Assembly
Step 5
Connect the 3-way pieces at the top of all vertical pipes of the frame as shown in the
image below
3 Way
3 Way
6
110 ” Pipe

Frame Assembly
Step 6
Connect the two 71” Pipe together with a straight connector and insert them in the front
and back of the frame using the 3-way canopy fitting opening.
Step 7
Then connect the 56 3/8” pipe to the top left and right sides of the frame.
Straight Connector
56 3/8” Pipe
56 3/8” Pipe
7
71” Pipe
Straight Connector

Enclosure Assembly
Step 2
Attach flaps from Nylon enclosure to the Frame.
The flaps are located at the bottom and top on
the left and right sides of the frame.
There are also flaps that run up the front side of
the frame and one that runs the length of the
center pipe.
Step 1
Unfold the Nylon Enclosure cover. Place it over
the top of the completed frame. The Nylon cover
should be placed to where the grommeted edges
are in the back of the frame and the Velcro strips
are in the front.
8

Enclosure Assembly
Step 3
Use bungees to attach the Nylon Surround to
the back and top side of the frame.
Insert the loop side of the bungee into the
grommet, sending it through until the ball
side stops it, wrap the loop around the pipe
and attach it to the ball side of the bungee.
Step 4
Use bungees to attach the Impact Screen to
the frame.
Using the same method as before, attach
the Impact Screen to the top, bottom, left,
and right sides of the frame.
Helpful Tip: Bungee the top left and right
corners of the screen first so it is suspended,
making it easier to attach all other bungees.
Note: Make sure the ball of the bungee is rotated away from the golfer.
9

Enclosure Assembly
Step 5
The Impact Screen comes equipped with
flaps that will cover the remaining
exposed pipe around the screen.
Attach the flaps to the Velcro strip
located on the nylon surround.
Step 6
Secure the weighted bag attachment to
the bottom of the screen.
The weighted bag pulls the bottom flap to
the floor, covering the bottom pipe and
creating a buffer for any golf balls that
may strike that part of the frame.
Step 7
Attach the Side Barrier Netting to the left
and right sides of the nylon enclosure.
The side barriers attach via Velcro, two
sand bags are included that will need to
be filled to keep the side barriers taut.
10

Impact Screen Care & Use
If you feel that your screen is being stretched too tight, try removing
bungees first. If it is still too tight adjust the pipe in the canopy fittings.
Keep enough space between the screen and any walls behind it to avoid
contacting them. This distance will depend on the force of your swing, but
in most cases 6-12” is sufficient.
We recommend using new golf balls that are free from any scuffs or
permanent markers to maximize the life of your screen.
Clean your clubs and golf balls regularly to keep your screen clean.
Remember that impact screens are “wearable” products, and depending
on the individual user, they may start showing wear immediately after first
use. This is normal. All of our impact screens, however, should withstand
several thousands of strikes from even the best golfers.
Always make sure your screen is completely clean and dry before storing
to avoid spots, mold, or mildew.
11

WE WELCOME YOUR
FEEDBACK!
Please feel free to contact us if you have any
questions or comments about using your new
products.
We can be reached on our website, via email,
or by giving us a call at 972-848-7491. Please
don’t hesitate to let us know if there is anything
we can do to help!
Visit:
https://youtu.be/qmt4R_7tcfA or
SCAN THE QR CODE TO VIEW A VIDEO ON HOW TO ASSEMBLE THE 9 x 12 Kit
SIENCLOSURESWING.