Showco Laser RGB User manual

Manual Showco
LASER RGB
www.carlosmendoza.com.mx

1
1. Open the box for checking
In order to use this product safety and reasonable for the users, please read over
this manual carefully before use and the operation must strictly according to this
manual to avoid any damage to the product and personal safety.
Once after received this products please take and put carefully . And check
carefully that whether the product was damaged or not during the transportation and
please check the following things were enclosed:
Laser light 1PC 1PC
3 pin signal line 1PC User manual 1PC
Power cable 1PC
2. Installation
1. Please check the voltage whether is the same with the one showed on the
equipment or not.
2. It must ask for the technical person and set the light safety when installation. And
let the light beam at the suitable angle.
3. When install this equipment please make sure there's no flammable surfaces
(decorated things, etc) within at least 1.5M and maintain minimum distance of
0.5M from the equipment to the walls.
4. Please make sure that there's no other equipment or decorating materials
obstructed the exhaust fan and the vent-pipe.
5. Products should be install immobility.
6. In case of safety, it's very important that to connect the earth with line.
Pin 25 ILDA Signal cable
www.carlosmendoza.com.mx

2
3. ATTENTION
ØPlease do not open the bottom cover yourself without permission. Operate it
accord the user manual. Please call the technician in case the machine broken
down.
ØDo not use it under the damp and rain.
ØPay attention to prevent the light from strong bump.
ØPrevent the dust into the product
ØKeep the vent-pipe well while working.
ØKeep the plug insert well before put into power.
ØDon't look the light directly to prevent make some destroy with eyes.
ØDon't light or extinguish frequently, otherwise the life span of the light tube will be
shortened.
ØIn view of the special characters, after operated the light an hour the product shall
be paused about 15 minutes before be used next time.
ØKeep the space between light equipments and the lighted things more than one
meter.
ØDon't touch the product and draw the power line if you hand wet.
ØDon't open the cover for there have no parts the user can repair.
ØDon't operate the light without lamps.
ØIf the semiconductor laser doesn't as light as before or there have some destroy
with lens or other parts, please contact the distributor in time.
ØWhen you want to retransfer the products, you'd better use the original package
to shockproof.
4. Maintain
Please use cotton stick dipped alcohol to wipe the mirrors at regular. Do
not use the wet cloth or chemical impregnant to clean the mirrors.
Please use the soft cloth to clean the surface of product.
ATTENTION:Disconnect input power before maintain.
NOTE: Don't seperate laser machine from laser power and repaire them by
yourself otherwise no good repair service will be supplied.i
Don't look straightly at the light sources.
www.carlosmendoza.com.mx

Fan
5. Structure of the fixture
3
Y scan board
X scan board
Signal switch PCB
power supplyLED
Scan mirror
Washer
Dustproof mirror
Lens holder
Power supply of green laser diode
Red laser diode
Power supply of red laser diode
Blue laser diode
Green laser diode
Power supply of blue laser diode
Fig5-1
No .
1
2
3
4
5
6
7
8
Description.
9
10
11
12
13
14
15
No . Description.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
www.carlosmendoza.com.mx
www.carlosmendoza.com.mx

4
Fig6-1
DMX plug signal
Power input plug
Power switch
Security key switch
MIC
6. Backboard Assembling Diagram
No . Description.
Male ILDA 25 plug
No . Description.
1
2
3
4
5
6
1
2
3
4
5
6
www.carlosmendoza.com.mx

(2) Optical system:
RGB mix beam be reflected out by X,Y scan mirrors.
7. Scan motor Replacement
(1) Steps:
1. Unscrew UK M6 screw and plug out male signal connector.
2. Disassemble all M4 10 screw from X,Y scanner socket so that scan motors can
be took out, put in and rotate scanner socket to adjust the scan angle.
3. After adjust ,fix M4 screws,plug in male signal connector and then fixUK
M6 screws.
10
Y scan motor
X scan motor
UK M6 screw (with femal screw)
Signal connector(Male)
M4 10 screw
M4 10 screw
Fig7-1 Scan motor install diagram
White beam
RGB mix beam
Fig7-2 Optical System diagram
5
www.carlosmendoza.com.mx
www.carlosmendoza.com.mx

8. Adjustable mirror socket
(1) Steps
1. Loose setscrew of X,Y and then adjust mirror socket to suitable position by X,Y
adjustable screws.
2. Adjust Z adjustable screw at same time.
3. Fix X,Y setscrew.
NOTE:Make sure all beams through adjustable mirror socket be one point when you
adjust X,Y,Z line with adjustable screw.
(2) RGB Laser beams mix system:
Mirror socket 1:Transmit red beam,reflect green beam,and then mix out yellow
beam through mirror socket 1.
Mirror socket 2:Transmit yellow beam,reflect blue beam ,and then mix out white
beam through mirror socket 2.
Y setscrew
Y adjustable screw
X adjustable screw
Z adjustable screw
X setscrew
setscrew
Fig8-1 Adjustable mirror socket structure
Blue beam
Red beam
Green beam
Yellow beam
White beam
Mirror 2 Mirror 1
Fig8-2 RGB laser beams mix system
6
www.carlosmendoza.com.mx

9. Laser diode replacement
Methods:
Disassemble whole laser system (include power supply,laser diode) and then
replace new one at original position.
Note:keep laser diode,power supply and cables be completly and don`t try to
damage,destroy or cut them so that it can be repaired (crefer fig9-1).
Fig9-1
Correct Method Wong Method
Snip
Snip
1
2
3
5
6
4
power supply of red laser diode
33445566
22
11
Green laser diode
power supply of blue laser diode
blue laser diode
power supply of green laser diode
red laser diode
22
66
22
66
7
www.carlosmendoza.com.mx
www.carlosmendoza.com.mx

8
1
2
3
4
5
6
7
POWER ON/OFF: Power on/off
DMX IN/OUT: International standard DMX512 signal input/output
MIN MAX: Sound control
MIC: Sound receiver
ILDA DB25F IN/OUT: Signal input connection port of the laser perform software that
in accordance with the ILDA standard.
POWER INPUT Input power, with inner fuse.
Security key switch Laser diode ON/OFF
Remote Lock In the event of remov al, laser will not emit a ny beam.(E.U. IE C regulation)
10. Control board instruction
8
DMX
Signal Work
Status
Security
key switch
IN DMX OUT
ILDADB-25F Connector-OUT
ILDADB-25M Connector-IN
POWER IN
OFF
ON
MIC
Remote Lock
MIN MAX
OFFON
1
2
3
45 7
86
MODE ENTER UP DOWN
DMX
Signal Work
Status
MODE ENTER UP DOWN
MODE: Select working mode or back to upper menu.
ENTER: Confirm setting or go to subordinate menu.
UP: Increase DMX address value.
DOWN: Decrease DMX address value.
DMXSignal: DMX512 input situation.. LED on means have input DMX512
otherwise no input DMX512 or input signal abnormality.
Work Status: LED on means display PCB work well otherwise it is not work in good
Condition.
1. Control board operation way:
www.carlosmendoza.com.mx

The machine can display two different patterns at the same time--24 channel version.And
the 2nd pattern can move with the main pattern-17 channel version,Also you can display one
pattern only--14channel version. The function of each channel as following(if the channnel
not mention main pattern or the 2nd pattern, it means this channel has effect for both two
patterns. Such as channel 1,4,11,12).
9
11. DMX512 Operate
2. Preset program mode (include DMX mode)
Press MODE to select work mode on LCD display. Use ENTER to active or close setting.
UP & DOWN to set DMX address code.
Working mode instruction:
ACCMusic Active: Accelerated music active
STDMusic Active: Standard music active
Automatic mode: Auto-mode
DMXAddr: DMX512 mode. Set address code under this mode. OPEN to active DMX
address value setting function. Then use UP & DOWN to select address
code value you need. Press SAVE to save setting and close DMX address
Code setting function.
LCD display memory function: Save setting automatic when you turn off fixture.
3. Computer software control mode
Fixture, there has a switch to select control mode - by computer or inside program:The
fixture has ILDA DB 25 connector so that it can be controlled by computer software. In the
When ILDA DB25F IN connects with QM2000 interfacial card or USB interfacial card, the
lamp will be control by software which installed in the computer. When ILDA DB25F IN
connector's connection port are free, the laser will driver by the inside program, temporality
it can control by music or DMX512 signal.
The control mode switch will check the 4th Pin (InterLock A) and the 17th Pin (
InterLock B) to adjust whether there has computer (with interfacial card) be connected to
fixture. If Pin 4 not be connected to Pin 17, it means there no interfacial card otherwise
there has and the connection port can receive all the signal of laser perform software that
accord with the ILDA standard, such as LD-2000 of Pangolin company.
In the theory, all the signal of laser perform software that accord with the ILDA Db25
standard can control the fixture. But Pin 4 and Pin 17 not be connected in some laser
perform interfacial card. You will need to sold this two pins together at Pin25 signal output
connector or connect Pin4 and Pin 17of the standard Pin 25 signal cable before use.
Note: We have tested that Pangolin Ld2000 (Qm2000 PCI interfacial card) and our
i.Top laser (USB2.0)interfacial card) can work with this fixture well. But you will need to
make changes as above mentioned when you use Mamba Black software ( Easylaser
interfacial card) of MediaLaser company.
www.carlosmendoza.com.mx

1
2
3
4
5
6
7
Channel
Control
Mode
42~83
84~125
126~167
DMX Value
0-41
168~209
210~255
0~16
17~33
34~50
51~67
68~84
85~101
102~118
119~135
136~152
153~169
170~186
187~203
204~220
221~237
238~254
255
0~255
0~255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
Main Pattern
Colour
Main Pattern
Speed
Main Pattern
Rotate
Main Pattern
Dot+
Rotating
Main Pattern
move
Function
Accelerated music active(Channel 2~24 no function)
Standard music active(Channel 2~24 no function)
Auto-mode(Channel 2~24 no function)
Sound accelerated manual mode
Manual(Sound active)
Manual(Auto-mode, movement auto active)
Close
Original colour
Red
Yellow
Green
Cyan
Blue
Purple
White
Single colour change
Stochastic Single colour
Rainbow colour flow
Static colour + strobe
Stochastic colour + strobe
Stochastic multi colour + strobe
Colour flow + strobe
256 patterns(0~255)
42 Class speed(0~255)/6=(0~42)
No Function
Horizontal Rotate(around Y axis)
Vertical Rotate(around X axis)
Horizontal & Vertical rotate
No Function
Rotating(around Z axis)
Dotting(only dot, no line)
Dot rotating
No Function
Horizontal Movement
Vertical Movement
Sidelong Movement
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
8
9
Main Pattern
Extend
No Function
Extend in Horizontal
Extend in Vertical
Extend in Horizontal & Vertical
No Function
From small to large
from large to small
From small to large and then from large to small
10
Main Pattern
Zoom
www.carlosmendoza.com.mx
www.carlosmendoza.com.mx

0~255
3~255
0~255
3~255
0~2
0~27
28~55
56~83
84~111
112~139
140~167
168~195
196~223
224~251
252~255
0~63
64~127
128~191
0~255
191~255
0~2
10
11
12
13
14
15
16
A B C
D E F
G H I
(0,0)
(255,255)
(0,255)
(0,255)
A (64,64)
B(128,64)
C(192,64)
D(64,128)
E(128,128)
F(64,128)
G(64,64)
H(128,64)
I(192,192)
Drawing speed
Scan speed
Color speed
Main patter
pattern Size
Twin patterns
&
position
Postion
Reference frame
the 2nd pattern
move mode
the 2nd pattern
16 Class speed(0~255)/17=(0~15) 0 no effect
Preset scan speed(Speed 50)
253 class speed(from fast to slow)
255 Class(Slow to fast)
Original Size(100%)
253 Class Size(3%~255%)
No double patterns & position(15~24 out of effect)
Pattern 1 Position B
Pattern 2 Position H
Pattern 1 Position A
Pattern 2 Position I
Pattern 1 Position D
Pattern 2 Position F
Pattern 1 Position G
Pattern 2 Position C
Pattern 1 Position H
Pattern 2 Position B
Pattern 1 Position I
Pattern 2 Position A
Pattern 1 Position F
Pattern 2 Position D
Pattern 1 Position C
Pattern 2 Position G
Pattern 1 Position E
Pattern 2 Position E
The 2nd pattern reverse with the main pattern(18~24 no effect)
The 2nd pattern rotate with the main pattern(18~24 no effect)
The 2nd pattern reverse alone(18~24 channel decide move mode)
The 2nd pattern rotate alone(18~24 channel decide move mode)
256 patterns
3~255
0~2
17 The 2nd
pattern size
Original size(100%)
253 Class size(3%~255%)
11
www.carlosmendoza.com.mx

0~16
17~33
34~50
51~67
68~84
85~101
102~118
119~135
136~152
153~169
170~186
187~203
204~220
221~237
238~254
255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
0~63
64~127
128~191
192~255
0~255
18
19
20
21
22
23
24
The 2nd
pattern colour
The 2nd
Pattern Rotate
The 2nd
Pattern
Dot rotating
The 2nd
Pattern
Move
The 2nd
Pattern
Extend
Zoom
Drawing speed
Colse
Original color
Red
Yellow
Green
Cyan
Blue
Purple
White
Single color change
Stochastic color change--original color + a new color
Rainbow flow effecf
Original color + strobe
Stochastic rainbow color + strobe
Rainbow flow + strobe
No Function
Horizontal rotate(around Y axis)
Vertical rotate(around X axis)
Horizontal & Vertical rotate
No Function
Rotate(around Z axis)
Dotting(Only dot, no line)
Dot rotating
No Function
Horizontal move
Vertical move
Sidelong move
No Function
Extend in Horizontal
Extend in Vertical
Extend in Horizontal & Vertical
No Function
From small to large
From large to small
From small to large and then to small
42 Class speed(0~255)/6=(0~42) 0 no drawing
Stochastic color + strobe
12
www.carlosmendoza.com.mx

12. Specification
ØVoltage: AC 100V~240V, 50/60Hz
ØTotal power: 50W
ØScanner:
Ø
Ø: 0~ 30
Ø
ØLaser light power:
Ø
ØNet weight: 15 kg
ØDimension: 640
13. Maintain
ØMaintenance should be performed every 15-day period, by using a sponge which is
dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the mirror.
ØWarning: Power must be disconnected before maintenance or repair. Do not look at the
light source directly.
NOTE: Don't seperate laser machine from laser power and repaire them by yourself
otherwise no good repair service will be supplied.
Super-speed scanner
Cooling mode: Air cooling
Scan angel
DMX Channel: 24 CHS
Red Laser Class 3B 650nm
Green Laser Class 3B 532nm
Blue Laser Class 3B 473nm
Control mode: Music mode, Auto-mode, DMX512
ATTENTION: DISCONNECT INPUT POWER BEFORE MAINT AIN.
DON'T LOOK STRAIGHTLY AT THE LIGHT SOURCES.
x 304 x 266 mm
13
www.carlosmendoza.com.mx

220
INT
~
V
+12V
0V
12345678910
ON
J1A
+
~~
7805CV
Lm324
LPC2214FBD144
TLC7528
TLC7528
Lm324
Lm324
Lm324
Lm324
Lm324
Lm324
Lm324
25P
25P
220V AC
IN
220VAC IN
+
-
220VAC
IN
+
-
220VAC IN
+
-
FUSE
FUSE
VR
1
RGB
23
1
2
3
75176
DMX Tr1+ Tr1- Tg1+ Tg1- Tb1+ Tb1- Tr2+ Tr2- Tg2+ Tg2- Tb2+ Tb2-
GND
-+
+15V
0V
-15V
AC10.8V
+-+-+-+-
FAN
MIC
VR
+
J5 J5
+24V
220v AC
IN
0V
-24V
Power LED
+
Ld2000 LED
+
MIC
+
1
9
Power supply
Power supply
Power switch
scan PCB
scan PCB Y scan motor
X scan motor
power supply
of red laser diode
red laser diode
power supply of
green laser diode
Green laser diode
Blue
laser diode
Manostat power
of blue laser diode
Blue aser diode
trasnsformer
on/off
switch
Remote control
connector
Pin 25 female PC plug Pin 25 male PC plug
14. Electrical diagram
14
TTL plug
TTL plug
TTL plug
www.carlosmendoza.com.mx
www.carlosmendoza.com.mx

15. Trouble shooting
15
Problem Causation Replace part Series number
No power
Damaged Fuse Fuse
Damaged Pin4 switch Pin 4 switch
Super scan motor
No beam or beam
dim or beam can't
close, but other
functions OK
Green laser diode
Can not control
other function
OK,Such as laser
diode and fans
24V
No response to
music or it is
difficult beactived
by music
MIC
Potentionmeter
X,Y scanner no
strength or no
patternor scanner
shaking 24V
Control mode
setting incorrect
Signal switch board 4
LT-6 address code board
Damaged Signal switch board Signal switch board 4
USB box USB box
USB signal cable
L 2000 signal cable
Red laser diode
Blue laser diode
09-00-2001-01
08-05-0420-02
16-03-0004-00
16-03-0001-00
26-2A-LT211V2-00
04-03-0105-03
15-01-2215-00
16-03-0004-00
26-2A-FASTSCAN-00
26-2A-Sigalsw4-00
16-03-0004-00
26-2A-LT6SW-00
USB21-KT-00
27-08-0005-00
07-01-0030-08
07-02-0020-02
07-03-0250-01
26-2A-LT211V2-00
26-2A-LT211V2-00
16-03-0019-00
26-2A-LT211V2-00
26-2A-Sigalsw4-00
Damaged power supply
Damaged mic
Damaged control PCB
Control PCB
Damaged potentiometer
Damaged scanner
Damaged control PCB
Control PCB
Damaged power supply
Damaged scan board Scan board
Dirty lens
Please refer to the
usermanual for
further instruction
Damaged laser diode
Damaged control PCB
Control PCB
Control mode
setting incorrect
Please refer to the
usermanual for
further instruction
Please refer to the
usermanual for
further instruction
Damaged control PCB
Control PCB
Damaged power supply
24V
Damaged address board
Internal wires
are disconnected
Damaged power supply
24V
Damaged Signal switch board
www.carlosmendoza.com.mx

Interlock A
Not connected
Interlock B
-5 to +5V
-5 to +5V
No use
Connected to Pin 17 inside the QM 2000
0v to +2.5v
0v to +2.5v
0v to +2.5v
No use
No use
No use
No use
No use
No use
+5V to -5V
+5V to -5V
No use
Connected to Pin4 inside the Qm 2000
-2.5V to 0V
-2.5V to 0V
-2.5V to 0V
No use
No use
No use
No use
Cable shielded
X
Y
No Use
Red
Green
Blue
No Use
No Use
No Use
No Use
No Use
X
Y
No Use
Red
Green
Blue
No Use
No Use
No Use
No Use
Ground
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
16
Appendix: ILDADB25F PINOUTSDB 25 definens
www.carlosmendoza.com.mx