PXM PxArt+ 6 User manual

MANUAL
PX390
PxArt+ 6
R

TABLE OF CONTENTS
1. General description....................................................................................................
2. Safety conditions........................................................................................................
3. Version data...............................................................................................................
4. Lamp description........................................................................................................
5. Manual change of lamp settings................................................................................
6. Co-operation with the PX277 configurator.................................................................
6.1 Description of the information parameters.................................................
6.2 Setting lamp parameters...........................................................................
6.2.1 Lamp colour and brightness address....................................................
6.2.2 Invert colour...........................................................................................
6.2.3 Flicker - Free.........................................................................................
6.2.4 Smoothing.............................................................................................
6.2.5 Smoothing time.....................................................................................
6.2.6 Restoring default settings......................................................................
6.2.7 Response to the lack of DMX signal.....................................................
7. DMX signal and power supply connection.................................................................
7.1 GLOBAL Trac GAC 600 adapter...............................................................
7.2 Section through the DMX bus-duct............................................................
8. RDM description of available parameters..................................................................
9. Device programming..................................................................................................
10. Dimensions..............................................................................................................
11. Technical data..........................................................................................................
Declaration of conformity...............................................................................................
3
3
5
6
7
8
9
9
9
10
10
11
11
11
12
13
13
13
14
16
17
18
19
Manufacturer reserves the right to make modifications in order to improve device operation.
PXM Marek Żupnik spółka komadytowa
ul. Przemysłowa 12
30-701 Kraków
tel.: [phone]
fax: [phone]
E-mail: [email protected]
Internet: www.pxm.pl
Rev 1.1
for Firmware 2.19

3
1. GENERAL DESCRIPTION
2. SAFETY CONDITIONS
Caution! Before installing, connecting, using and maintaining the lamp, you
must absolutely read this document.
The following symbols are used to emphasise important information on security conditions on
the product and in this manual.
Danger!
Risk of loss of life and
health.
Warning!
Fire hazard.
Warning!
LED light emission.
The risk of eye
damage.
Warning!
The risk of burns.
Warning!
Read this instruction
manual.
Do not look at the LEDs at a shorter distance than 2.0 m from the front surface of the
tube without proper eye protection. At a shorter distance, LEDs can cause damage or
eye irritation. Do not look at the light source directly through any optical instruments,
which focus the light rays.
Caution!
PxArt+ 6 is a professional LED illuminator designed for illumination of museum exhibitions or
displays.
Thanks to the application of the most modern semiconductor SSL LED light sources and
advanced control electronics, a high class illuminator was created which meets very high
requirements for museum and exhibition lighting. Its most important advantages include a
complete lack of ultraviolet radiation emission, trace amounts of infrared radiation, a very high
factor of CRI colour capturing, smooth adjustment of colour temperature of emitted light, large
brightness and small energy consumption.
®
The device features a base which allows for mounting it in GLOBAL Trac Pulse control bus bars,
provided with an additional control line.
Two individual addresses allocated to each lamp allow for independent adjustment of its
brightness and colour temperature, regardless of the settings of other lamps.
Through push buttons located on the lamp casing it is possible to operate it manually (e.g. in case
of connecting the lamp to bus bars without a control line).
®
Highly-effective LEDs made by Osram Oslon are used in the lamp with an efficient control
system, through which the lamp emits small amounts of heat.
The lamp casing renders it possible to change the direction of its beaconing in two axes.

PX390 is powered directly from a standard 230 V grid. Failure to observe safety instructions may
result in electric shock and pose a threat to life.
Therefore, it is necessary to observe the following rules:
1. Installation should be performed by a person holding the appropriate qualifications, according
to the instruction manual.
2. Lamp can be connected only to a grid which meets the safety conditions (3-wire grid, equipped
with a circuit breaker).
3. Protect all cables against mechanical and thermal damage.
4. In case of failure of any of the cables, it must be replaced with a cable of the same technical
parameters.
5. All repairs can only be carried out with power disconnected.
6. The device with visible mechanical damage cannot be connected to the mains.
7. Avoid sudden shocks, particularly dropping.
8. The device must not be used in rooms with a temperature below 2 °C or above 40 °C.
9. Clean only with a damp cloth – the lamp must be at this time completely disconnected from the
power supply.
In case of improper usage of the product it may cause a risk of serious injury or death,
because of the threat of fire.
While working outdoors in normal conditions, the housing unit can heat up to +60°C.
Make sure that accidental contact with the device during use is impossible.
4
From a distance of more than 2.0 m from the outer housing of the lamp and LEDs, the light is
harmless to unprotected eyes.

There are several versions of the PX390 lamp which are different from each other as far as
the type of the reflector applied.
Below there is a description of designations of PX390 models with explanation:
PX390-XX-YY-Z
XX - the reflector angle
Available values:
o
10 - 10
o
20 - 20
o
30 - 30
o
40 - 40
EL - elliptical
YY - colours of applied LEDs
MW - multi white (dynamic white)
MC - color (RGB)
Z - housing colour
1 - grey
2 - black
3 - white
Example of lamp designation:
PX390-20-MW-1
3. VERSION DATA
5
Lamp catalogue number
The reflector angle: 20°
Colour of applied LEDs:
dynamic white
Lamp housing colour: grey
The dimming of the lamp brightness occurs when the temperature is above 70 °C; this prevents
the device from overheating. If the device reaches a temperature of 90 °C, the power of the lamp
will be totally reduced. The light is then switched automatically in the event of temperature drop
below the maximum temperature (90°C). The higher the temperature of the device, the greater is
the brightness dimming.

4. LAMP DESCRIPTION
6
o
360
1 3
4
5
1
2
3
4
a 3-phase track for GLOBAL
®
Trac Pulse control
2
end feed
power cable
DMX cable (shielded cable, 2-core
cable)
GLOBAL Trac GAC 600 adapter
5
DMX+ DMX-
GND

The lamp has been equipped with buttons which allow for changing the brightness level and
colour temperature of light. The buttons have been placed at the bottom part of the junction box,
above the lamp reflector. One button is responsible for one parameter.
The available buttons and connector for connecting the PX277 programmer have been shown in
the figure below:
7
Above the reflector there is a diode which indicates the condition of the lamp.
Depending on a situation, the diode signals the following:
! start of the lamp – quick flickering of the diode for 2 seconds,
To change the brightness or temperature colour, press and hold down the appropriate control
button. If during the brightness or colour temperature adjustment the button diode starts
flickering, it means that the extreme value (minimum or maximum) has been reached. Then the
direction of adjustment changes.
It is possible to change the adjustment direction without reaching extreme values. For example,
while the lamp brightness is increased, release the control button for a moment. The diode will
signal the change of adjustment direction. The pressing of the adjustment button again will cause
the dimming of the lamp (brightness decrease).
While the lamp operates, the diode stays switched off (excluding situations mentioned above).
For lamps with RGB LEDs configuration, programming buttons available under the reflector have
the following functions:
! DMX signal receiving – slow flickering of the brightness adjustment button (1Hz frequency) in
the first minute after receiving the DMX signal,
! after the start of the lamp in case of the loss of DMX signal – diode lights (continuously) for 1
minute,
! if the state of DMX signal is changed (if there was no DMX signal and it returned, or vice
versa) – diode signals it for 1 minute,
! damage of the temperature sensor module – diode does not go out after 1 minute.
ź colour temperature adjustment button - change of light colour
ź brightness adjustment button - change of the brightness value
5. MANUAL CHANGE OF LAMP SETTINGS
Parameter programming
connector (using PX277)
Brightness adjustment
Colour temperature
adjustment

6. CO-OPERATION WITH THE PX277 CONFIGURATOR
Lamp settings can be changed by connecting the PX277 PxArt Settings Controller configurator.
At the moment of connection, the PX390 starts again which causes LEDs to be off for a while and
the diode indicating the DMX signal condition pulses for 2 seconds.
When the device is turned on, its name appears on the display. The main menu allows a preview
of many lamp parameters from PxArt series and a change of the following options: colour and
brightness address, scene brightness and colour, colour inversion, smoothing, change of
smoothing time, Flicker free and restoration of default parameters.
Furthermore, it is possible to check the lighting time and lamp operation time (total lamp operation
time, also without switching the diodes off). Additionally, information concerning minimum,
maximum and current temperature reached by the lamp is displayed.
PxArt Settings Controller also allows for checking the version number of the software which is
installed in the lamp, its serial number and model.
Navigating through the menu is possible with programmer buttons located below the display. The
"escape" button allows an exit to the upper level in the device menu; "next" and "previous" buttons
make it possible to go forward and backward (alternatively value decreasing or increasing).
However, the "enter" button allows you to enter the edition of the selected menu or to confirm the
edited value.
Lamp
parameter value
DMX signal value
Colour temperature
adjustment (Lamp colour)
Brightness adjustment
(Lamp brightness)
4500K
100%
3600K
50%
255
255
2700K
128
0
0%
128
0
Setting lamp parameters - DMX signal value:
8
Invert colour
Turning off
Invert colour
Turning on
0
128
255

6.1. Description of the information parameters
PX277 controller allows you to read important information concerning the lamp to which it has
been connected.
Model
PX390 +6 MW
Temp. min max
23.0°C 53.3°C
Current temp.
25.5°C
Lighting time
00y 001d 06h:48m
Working time
00y 000d 07h:00m
10x NEXT
NEXT
NEXT
NEXT
Serial Number
2015210005
Version
ver 2.19
NEXT
NEXT
Lamp serial number
Lamp operation time (total operation time of the lamp, also
without diodes turned on) and lighting time are presented as
follows (designations from the left):
- years (numbers next to letter "y”),
- number of days (letter "d”),
- hours (letter "h”),
- minutes (letter "m”).
Version number of the software
installed in the PX390 lamp
Lamp model
Information concerning the minimum, maximum
and current temperature reached by the lamp.
A unit expressed in [°C]
6.2 Setting lamp parameters
6.2.1 Lamp color and brightness address
PX277 allows for changing the DMX address which controls the color and brightness of the lamp.
The lamp has the DMX channel assigned whose value can be changed depending on the needs.
DMX channel can be set between 1 to 512.
To change the DMX channel (which is
responsible for the lamp function), select in the
PX277 menu a [Color address] or [Bright.
address] option, confirm by pressing "enter"
and then set an appropriate value using
"previous" and "next" buttons. After the change
of the DMX channel, the operation has to be
confirmed by pressing "enter".
Color address
001
Color address
001 *
ENTER
Color address
512 *
NEXT
Model
PX390 +6 MW
NEXT
9

6.2.2 Invert color
Invert color
Off
Invert color
Off *
ENTER
Invert color
On *
NEXT
Model
PX390 +6 MW
5x NEXT
The [Invert color] function applies both to
normal operation of DMX and operation in no
signal mode.
Enabling this option results in changing the
DMX interpretation according to the
scheme:
Value: 0 Value: 255
Warm white Cold white
SWITCHING ON
THE FUNCTION
Invert color
Value: 0 Value: 255
Cold white Warm white
6.2.3 Flicker-Free
Flicker free
On
Flicker free
On *
ENTER
Flicker free
Off *
NEXT
Model
PX390 +6 MW
6x NEXT
The “Flicker free” technology allows for
avoiding an unpleasant flickering of light
during video recording.
Bright. address
001
Bright. address
001 *
ENTER
Bright. address
512 *
NEXT
Model
PX390 +6 MW
2x NEXT
10

The device also has the smoothing option which enables smooth brightness and colour
modifications. When the function is turned on, the transitions between successive DMX values
sent to the lamp (responsible for brightness and colour changes) occur smoothly, without visible
jolts, which prevents light "vibration" effects in the lighting systems.
Smooth
Time *
Smooth
Off *
NEXT
Smooth
P2P *
NEXT
Smooth
Time
ENTER
Model
PX390 +6 MW
7x NEXT
6.2.5 Smooth time
The next two DMX values sent to the
lamp are linearly smoothed between
DMX signal packets for the selected
option [P2P] or the time interval set in
the menu [Time].
When the PxArt Settings Controller time smoothing function is active, it allows for changing the
smoothing time value. As a result it enables an acceleration or deceleration of the brightness and
colour parameter change. Maximum available value is 2000 [ms] and minimum is 10 [ms].
[ ] - makes it possible to
change the time parameter at which
subsequent different DMX signal values
sent to the lamp are smoothed among
themselves. The user may set the
smoothing time using "previous" and
"next" buttons.
Smooth time
Smooth time
0200[ms]
Smooth time
0010[ms] *
Smooth time
2000[ms] *
NEXT
ENTER
Model
PX390 +6 MW
8x NEXT
6.2.4 Smoothing
6.2.6 Restoring default settings
The device comes with the option to restore default settings.
To use this option, select the [Default sett.] menu and press "enter".
A window informing about the need to press "previous" and "next" buttons will appear for 2
seconds simultaneously. Next, the device will display [Reset OK...] message and default settings
will be restored.
11

Default sett. Default sett.
PREV+NEXT > 2s
PREV+ NEXT
Default sett.
Reset OK
Model
PX390 +6 MW
9x NEXT
ENTER
PX390 default setting:
ź Color address 001
ź Brightness address 001
ź Scene color 128
ź Scene brightness 128
ź Invert color Off
ź Flicker free On
ź Smooth Time
ź Smooth time 200 [ms]
6.2.7 Response to lack of DMX signal
In case of no DMX signal, the scene executed is the one whose parameters are adjusted by the
user using [Scene color] and [Scene brightness] options. This function is used to gain control of
LEDs without connecting an external controller.
Automatic connection of DMX signal will stop the executed scene and the lamp will operate in
accordance with the parameters of the control signal.
The change of scene colour and brightness is possible directly from the lamp (buttons) or with the
use of PX277. These values can be set between 0 and 255.
Scene bright.
000 *
ENTER
Scene bright.
255 *
NEXT
Scene bright.
128
[Scene color] – if set to 0, changes the
colour temperature value of the lamp to
warm, and 255 to cold. 128 sets the neutral
colour temperature. Values between the
above values correspond to the colours
between the described extreme colours
(warm white and cold white). If the [Invert
colour] option is enabled, the warm
temperature colour of the lamp has the value
of 255, and cold – 0.
[Scene brightness] – if set to 0, it turns off
the scene, and 255 turns it on at 100%. 128
means that the scene brightness is set to
50%. After changing the value of scene
brightness, the operation has to be
confirmed by pressing "enter” or “escape”.
Scene color
000 *
ENTER
Scene color
255 *
NEXT
Scene color
128
Model
PX390 +6 MW
3x NEXT
NEXT
12

13
7. DMX SIGNAL AND POWER SUPPLY CONNECTION
7.1. GLOBAL Trac GAC 600 adapter
®
7.2. Section through the DMX GLOBAL Trac Pulse
control bus-duct
4
31
2
6
5
7
7
1
2
3
4
5
6
phase 3
phase 1
phase 2
neutral
DMX +
GND
DMX -
POWER
DMX
5
1
2
3
4
DMX CONTACTS
POWER CONTACTS
neutral (phase 3 on the opposite
side)
phase selector switch
phase 1 (phase 2 on the opposite
side)
earth
2
3
4
5
1DMX - (on the opposite side
DMX +)
3 1 2

14
8. RDM DESCRIPTION OF AVAILABLE PARAMETERS
PX390 supports the DMX-RDM protocol. DMX protocol in its assumption enables one-way data
flow while its extension, the RDM protocol, can transmit information in two ways. This makes the
simultaneous receiving and sending of information possible and allows for monitoring the
operation of devices compatible with the RDM protocol as well as gives the possibility of changing
the configuration of their parameters.
Below there is a list of RDM parameters supported by PX390:
PiXiMo
3700
www.pxm.eu
NTC
12
Parameter name
PiD
Description
SUPPORTED_PARAMETERS
0x0050
all supported parameters
PARAMETER_DESCRIPTION
0x0051
description of additional parameters
DEVICE_INFO
0x0060
information concerning the device
SOFTWARE_VERSION_LABEL
0x00C0
firmware version of the device
DMX_START_ADDRESS *
0x00F0
DMX starting address of the device,
minimum value: 1, maximum value: 512.
According to the RDM standard, for device
whose footprint is 0, the value of this
parameter may be 65535 and then it is not
possible to change the initial address settings
for the entire device, but only for sub-devices.
IDENTIFY_DEVICE *
0x1000
device identification,
Two states are possible: identification is off
(0x00 value) and identification is on (0x01
value).
DEVICE_MODEL_
DESCRIPTION
0x0080
device description, e.g. name
MANUFACTURER_LABEL
0x0081
manufacturer description, e.g. name
DEVICE_LABEL *
0x0082
additional device description,
It is possible to enter an additional device
description using up to 32 ASCII characters.
FACTORY_DEFAULTS
0x0090
device default settings
DMX_PERSONALITY
0x00E0
DMX operational mode
DMX_PERSONALITY_
DESCRIPTION
0x00E1
description of individual operational modes
SENSOR_DEFINITION
0x0200
information concerning the selected
temperature sensor
SENSOR_VALUE
0x0201
information concerning sensors
DEVICE_HOURS
0x0400
information concerning the working time of the
device counted in hours
LAMP_HOURS
0x0401
information concerning lamp lighting time
Nazwa parametru
PiD
Opis
SUPPORTED_PARAMETERS
0x0050
wszystkie wspierane parametry
PARAMETER_DESCRIPTION
0x0051
opis parametrów dodatkowych
DEVICE_INFO
0x0060
informacje na temat urządzenaia
SOFTWARE_VERSION_LABEL
0x00C0
wersja firmware urządzenia
DMX_START_ADDRESS *
0x00F0
początkowy adres DMX urządzenia,
Minimalna wartość to 1, a maksymalna 512.
Zgodnie ze stadardem RDM dla urządzenia,
którego footprint wynosi 0, wartość tego
parametru może wynosić 65535 i wówczas nie
ma możliwości zmiany ustawienia adresu
początkowego całego urządzenia, a jedynie
podurządzeń (subdevices).
IDENTIFY_DEVICE *
0x1000
identyfikuj urządzenie.
Możliwe dwa stany: identyfikacja wyłączona
(wartość 0x00) oraz identyfikacja włączona
(wartość 0x01).
DEVICE_MODEL_
DESCRIPTION
0x0080
opis urządzenia np. nazwa
MANUFACTURER_LABEL
0x0081
opis producenta np. nazwa
DEVICE_LABEL *
0x0082
dodatkowy opis urządzenia,
Możliwe jest wpisanie dodatkowego opisu
urządzenia stosując do 32 znaków ASCII.
FACTORY_DEFAULTS
0x0090
ustawienia domyślne urządzenia
DMX_PERSONALITY
0x00E0
tryb pracy DMX
DMX_PERSONALITY_
DESCRIPTION
0x00E1
opis poszczególnych trybów pracy
SENSOR_DEFINITION
0x0200
informacja na temat wybranego czujnika
temperatury
SENSOR_VALUE
0x0201
informacje na temat czujników
DEVICE_HOURS
0x0400
informacje na temat czasu działania
urządzenia liczony w godzinach
LAMP_HOURS
0x0401
informacje na temat czasu świecenia lamp
TEMPERATURE_LIMIT_
ON/OFF
0x800E
aktywacja ograniczenia temperaturowego dla
podłączonego czujnika temperatury do
drivera,
Dla wartości 0 funkcja nie aktywna, wartość 1
funkcja włączona. Domyślna wartość to 1.
TEMPERATURE_
THRESHOLD_LOW
0x800F
dolna wartość temperatury, dla której
aktywowane jest ograniczenie temperatury
TEMPERATURE_
THRESHOLD_HIGH
0x8010
górna wartość temperatury, dla której aktywne
jest ograniczenie temperatury tj. temperatura
wyłączenia wyjść z drivera
SMOOTH_DIS_0/P2P_
1/TIM_2 *
0x801A
wybór opcji dotyczącej funkcji Smooth
(wygładzania),
Dla wartości 0 funkcja wygładzania jest
wyłączona, dla wartości 1 funkcja wygładzania
pracuje w trybie Packet to Packet (P2P), a dla
wartości 2 wygładzanie pracuje w trybie
czasowym. Domyślnie ustawiona wartość 0 -
wygładzanie wyłączone.
SMOOTH_TIME *
0x801B
czas wygładzania dla funkcji TIM (time)
wybranej w punkcie powyżej,
Jednostka wyrażona w [ms]. Minimalna
wartość parametru to 10, a maksymalna
2000 [ms]. Domyślna wartość to 200 [ms].
SCENE_COLOR *
0x8021
ustawienie temperatury barwowej,
Wartość minimalna to 0, a maksymalna 255.
Domyślnie ustawiona wartość to 128.
SCENE_BRIGHTNESS *
0x8022
ustawienia jasności,
Wartość minimalna to 0, a maksymalna 255.
Domyślnie ustawiona wartość to 128.
FRICKER_FREE_ON/OFF *
0x8023
usunięcie efektu migotania obrazu,
Dla wartości 0 funkcja usunięcia efektu
migotania jest wyłączona a dla wartości 1
włączona. Domyślnie ustawiona wartość to 1.
SERIAL_NUMBER
0x8030
numer seryjny urządzenia
INVERT_COLOR_ON/OFF *
0x8038
odwracanie charakterystyki barwy światła,
Dla wartości 0 funkcja jest wyłączona a dla
wartości 1 włączona. Domyślnie ustawiona
wartość to 1.

15
Parameter name
PiD
Description
TEMPERATURE_LIMIT_
ON/OFF
0x800E
temperature limitation activation for the
temperature sensor connected to the driver,
For 0 value, the function is not active; for 1
value, the function is active. Default value is 1.
TEMPERATURE_
THRESHOLD_LOW
0x800F
lower temperature value for which the
temperature limitation is being activated
TEMPERATURE_
THRESHOLD_HIGH
0x8010
upper temperature value for which the
temperature limitation is active, i.e. the cut-off
temperature for exits from the driver
SMOOTH_DIS_0/P2P_
1/TIM_2 *
0x801A
selection of the options concerning Smooth
function,
For 0 value, the smooth function is off; for 1
value, the smooth function operates in the
Packet to Packet mode (P2P) and for 2 value,
the smooth function operates in the time
mode. Value 0 set by default – smoothing off.
SMOOTH_TIME *
0x801B
smoothing time for TIM (time) function
selected in the above point,
Unit expressed in [ms]. Minimum parameter
value is 10 and maximum is 2000 [ms].
Default value is 200 [ms].
SCENE_COLOR *
0x8021
color temperature settings,
Minimum value: 0, maximum value: 255.
Default value is 128.
SCENE_BRIGHTNESS *
0x8022
brightness settings,
Minimum value: 0, maximum value: 255.
Default value is 128.
FRICKER_FREE_ON/OFF *
0x8023
elimination of the flickering effect,
For 0 value, the function of eliminating the
flickering effect is disabled, and for 1 value, it
is enabled. Default value is 1.
SERIAL_NUMBER
0x8030
device serial number
INVERT_COLOR_ON/OFF *
0x8038
inversion of the light colour characteristics,
For 0 value, this function is disabled, and for 1
value, it is enabled. Default value is 0.
* - parameter editable

9. DEVICE PROGRAMMING
Smooth
Time
Smooth time
0200[ms]
Bright. address
001
Scene bright.
128
Model
PX390 +6 MW
NEXT
Working time
00y 000d 07h: 48m
Temp. min max
23.0°C 53.3°C
Default sett.
Lighting time
00y 001d 06h: 48m
Current temp.
25.5°C
NEXT
ENTER
Serial Number
2015350050
Version
ver 2.19
Bright. address
001 *
Bright. address
512 *
NEXT
Scene bright.
000 *
Scene bright.
255 *
NEXT
ENTER
Smooth
Off *
Smooth
P2P *
NEXT
Smooth
Time *
NEXT
ENTER
Smooth time
0010[ms] *
Smooth time
2000[ms] *
NEXT
Default sett.
PREV+NEXT >2s
PREV+ NEXT
Default sett.
Reset OK
ENTER
ENTER
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
Color address
001
NEXT
Color address
001 *
Color address
512 *
NEXT
ENTER
Scene color
128
NEXT
Scene color
001 *
Scene color
255 *
NEXT
ENTER
Invert color
Off *
Invert color
On *
NEXT
ENTER
Invert color
Off
NEXT
Fricker free
On *
Scene bright.
Off *
NEXT
ENTER
Fricker free
On
NEXT
16

10. DIMENSIONS
17
Ø 92
134
225
283,5
Dimensions are given in millimetres

18
11. TECHNICAL DATA
Power supply:
Number of LEDs:
Power input:
Max. increase of the housing temp.:
Luminous flux:
Lifetime of diodes:
Angles of reflectors:
Color temperature:
Brightness regulation extension:
CRI colour rendering index CRI:
Control protocol:
Available housing colours:
Weight:
Dimensions:
230 V AC
6
10 W
+ 30° C
600 lumens
50 000 h
10°, 20°, 30°, 40°, EL
2700÷4500 K
0÷100%
min. 90
DMX-512 / RDM
Silver, black, white
1,3 kg
Width: 134 mm
Height: 225 mm
Diameter of the reflector: 92 mm
Spectral characteristics of the emitted light

19
PXM Marek Żupnik sp. k.
ul. Przemysłowa 12
30-701 Kraków
PxArt+ 6
PX390
PN-EN 60598-1:2011
PN-EN 62471:2010
PN-EN 61000-4-2:2011
PN-EN 61000-6-1:2008
PN-EN 61000-6-3:2008
Pay attention to the correct connection of power
cables.
Maintenance can be performed only while the
current rails system is off.
DMX signal has to be connected by using a
shielded cable, connected to the GND pin.
mgr inż. Marek Żupnik
Name of producer:
Address of producer:
declares that the product:
Name of product:
Type:
answers the following product specifications:
LVD:
EMC:
Additional informations:
Kraków, 18.05.2015
DECLARATION OF CONFORMITY
according to guide lines 2004/108/WE and 2006/95/WE
tel: [phone]
fax: [phone]
e-mail: [email protected]
http://www.pxm.pl
ul. Przemysłowa 12
30-701 Kraków
Konsole teatralne i estradowE Cyfrowe ściemniacze mocy SYSTEM dmx Sterowniki ARCHITEKTONICZNE OŚWIETLENIE LED